AIM:        ‘Solving Second Order Equation’.   OBJECTIVE: Write a program in Matlab/Octave that will simulate the pendulum motion. Write a program that solves the following ODE. This ODE represents the equation of motion of a simple pendulum with damping.   THEORY:     1.What is a Simple Pendulum?          A simple pendulum…

AIM: Write a function that extracts the 14 coefficients and calculates the enthalpy,         entropy and specific heats for all the species in the data file. And, also calculate the molecular weight of each species and display in the command window.   THEORY:       a:Parsing…

AIM:         To write the code to calculate the global maxima of the stalagmite function and to explain the syntax for genetic algorithm(ga) in MATLAB.   OBJECTIVE: To write a code in MATLAB to optimize the stalagmite function and find global maxima of the function. To explain…

STUDY-1 AIM: To simulate a simulink model of a doorbell using solenoid block and observe the output. OBJECTIVE: To create a situation where the switch is closed for 2 seconds and then released. To observe the physical movement of the plunger.                      …

AIM:      (a). To Implement control logic of a “washing machine” using Stateflow as per given sequence.     (b). To Make a Simulink chart for the “Gear shift” logic as per below conditions. Given Data:          (a).…

SIMULATION OF BAJA ALL-TERRAIN VEHICLE   AIM:      To study and analyze the BAJ All-Terrain Vehicle(ATV) using simulink models. OBJECTIVE:      To prepare a technical report explaining the model properties & comments on the results. THEORY: All-Terrain Vehicle         An…

AIM: To Create the tooling axis for the given Fan cover model meeting the requirements of the draft angle and perform the Draft analysis on the model of Class-A surface. Objective:            If you're designing a product that will be manufactured using injection molding, use the Draft…

Aim:     To create the base bracket plastic component through the given Class-A surface and at the end performing the draft analysis on the model. Objectives: To ensure proper tree structure is followed. Geometrical sets should have a proper name based on the sketches present inside of it. All the sketches should…

Aim: To create the base bracket plastic component through the given Class-A surface and at the end performing the draft analysis on the mode. Abstract: In this project, I design a Switch Bezel using Catia v5. I received input as Class A Surface. I Check the direction to eject the tool based on the component design. Later…

AIM: To generate the draft analysis of the arm rest model. OBJECTIVE:           To create the Door Arm Rest  Class-A surface to final solid model and at the end performing the draft analysis on the model. THEORY:           Draft analysis helps to detect if your drafted…

Aim:       To create the Coin Holder Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model.  Take the Thickness of the component…

AIM: To create a switch bezel from the given A-class surface by considering a thickness of 2.5 mm and also creating Core and Cavity blocks for it. PROCEDURE: A class surface : The input of the product designer is in the form of the A-class surface. The job of the product designer is to create the B and C surfaces keeping…

    INTRODUCTION           Ribs are thin, wall-like features typically designed into the geometry of a part to add internal support to walls or other features. They provide a means to economical stiffness and strength in molded parts without increasing overall thickness. OBJECTIVE  …

Aim : -  To create a bose and dog house upon coin holder component and check the draft analysis for the component. General Guidelines for Bosses:   Draft  - 0.5 degrees on walls of boss   Thickness -  Typically 40%* of the nominal wall at the base.   Height to Diameter Ratio…

  AIM: Create the Base Bracket Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model.  Create the Heat Stakes and the locators considering the…