Creating a Wardrobe detailed drawing, Floor Plan, Kitchen Layout and Column Detail using AutoCad
AIM:
To draw the elevation & details of a wardrobe as shown in the figure below.After sketching & to provide the dimensions & text with the use of layers.
PROCEDURES:
DWG-1:
STEP 1,
1. Units are set in mm, Limits are set.
2. Taking Rectangle in command line as (2800,2600).
3. In the command line type offset.
offset from the top of dimension 12 & 488mm.
4. In the command line type offset.
5. Create the offset from the side at the distance of 608.5 & 365.
6. Create the offset from the bottom of dimension 100 & from 100 take 900 offset. by using hatch give the hatch & transprency in hatching setting & give scale 20.
in the command line type Qleader to mention the annotations.
7. Give the dimensions & Labeling.
STEP 2,
1. In the command prompt type Rectangle 630 X 2800
2. Take offset from side 2435mm.
3. In the command line type Qleader to mention the annotations.
4. Give the dimensions & Labeling.
STEP 3,
1. In the command line Rectangle 2800 X 2600 with the help of command drawers & cabinets are created.
For the drawers & cabnet give the grey colour.
2. Take offset from side 12,1223,1200.365
3. Take offset from bottom 900.
4. Dimension the drawing.
STEP 4,
1. In the command line Rectangle 520 X 630,1180 X 630,900 X 630,900 X 630 This is repeated 2 times
2. Using line commands,the next of the lines are drawn.
3. Dimension the drawing.
4. Place the entire drawing in the respective layer.
RESULT:
DWG-2
AIM: To draw the given floor plan.
PROCEDURE:
1. Units are set in mm. Limits are set.
2. In the command line type XL to draw the infinite lines.
3. In the Command prompt type offset to offset the line for a particular diastance.
4. Using arc command doors are also created.
Doors & Ventilators:
01 D1= 1000*2000mm
V1=800*500mm
02 D2=900*2100mm
V2=750*500mm
03 D3=800*2100mm
04 D4=750*2100mm
05 D5=700*2100mm
06 SD=2256*2100mm
Windows:
W1=2700*1500mm
W2= 2500*1500mm
W3=900*1500mm
W5=1000*1500mm
W9=800*1500mm
To draw canopy
CIRCLE:
1. In the menu bar click on circle.centre,radius.
2. Specify the centre point as 10,10 & radius 452.
3. In the menu bar click on circle > centre,radius.
4. Specify the centre point same as the previous circle (10,10) & radius 1398
SEATS:
1. In the menu bar click on rectangular,specify the length of the rectangle as 662.3.
2. Specify the width of the rectangle 298.0
3. In the command prompt type Filllet >radius>100
4. Take circle.2 points
5. Take circle>centre>diameter
6. Centre is the midpoint of the line,diameter is 719
7. Take circle>centre>diameter
8. Centre is the midpoint of the line,diameter is 777.2
9. Now, Extends the centre line & trim the extar's
10. In the menu bar click fillet>blend curves>& select the arc.
11. In the Menu bar click Fillet >Blend curves>& select the arc.
12. In the menu bar click Fillet>Blend curves> & select the arc.
13. Give the dimensions as per given in drawing & annotation with the text where ever required.
14. Place the all elements of the in the respective layers.
RESULT:
DWG-3
AIM: To create the kitchen layout & to Also,Use proper dimension techniques to dimension the kitchen layout.
PROCEDURE:
1. Units are set in mm, Limits are set.
2. In the command prompt type rec & the dimension are 4734 & 3688mm
3. Take offset it to the distance of 250mm.
4. Using arc lines the door is drawn.
5. In the command prompt type hatch to hatch the model.
6. In the command prompt type rec>dimension ,to do the fridge
7. Take offset it to the desired distance to get the micro oven.
8. Take trim to trim the extras.
9. Offset it to the horizantal distance of 350,450,900,450 & 560.
10. Offset & Offset it to the vertical distance of 600
11. In Type trim command & trim the extras.
12. In the command type line type & load the dotted lines.
13. In the command type text to text the given annotations.
14. Given the dimension as per the plan.
15. In the command prompt even the leader command is used to name the dimension.
16. Place the all elements of the in the respective layers.
RESULT:
DWG-4
AIM: To sketch the column details.
PROCEDURE:
1. Units are set in mm & Limits are set.
2. Using rectangle & line command line tables are drawn.
3. Using text command,the text is given.
4. In the command type lines to draw the reinforcement.
5. Type circles to draw the reinforcement.
6. Give the dimensions as per given in drawing & annotation with the text where ever required.
RESULT:
DWG-5
AIM: To draw the raft layout.
PROCEDURE:
1. Units are set to engineering>inches & Limits are set
2. In the command type Rectangle>dimensions are 29'-7" & 60'
3. To get dotted lines click on line type & load the dotted lines >set current. with the help of dotted lines & offset command the grids are drawn.
4. In the command offset the distance to 4"
5. In the Ribbon >hatch>AR-CON
6. In the command type rec 2'*2'
7. Take rectangle to draft the columns.
8. In the ribbon bar select hatch>ANSI37 hatch the columns
9. In the ribbon bar select hatch>ANSI33 hatch the columns
10. Take the Annotate>Text the given annotations.
11. Given the dimension as per the plan.
12. Place the all elements of the in the respective layers.
RESULT: