1. Mix proportion of concrete using fly ash as a part of the replacement of OPC The Concrete Mix Design for M35 grade concrete with fly ash       1. Stipulation for proportioning:  a. Grade of designation: M35 b. Type of cement: OPC 43 grade conforming to IS 8112 c. Type of mineral admixture: Fly ash…

A Sketch of the G+1 floor residential plan Dimensions of Ground Floor plan- Living room- 3.60m X 5.85m Kitchen room- 3.60m X 3m Dining room- 3m X 3m Master bedroom- 4.3m X 3m Bedroom- 3m X 4.5m Toilet- 3.25m X 1.2m Bath- 2.4m X 1.2m WC- 1.2m X 1m Dimensions of First Floor Plan- Guest room- 4.3m X 3m Study room- 3m X 3m…

Aim: To draw 1. Architectural drawing of a residential building: Plan of a residential building. Elevation of a residential building. Section of a residential building. 2. Structural drawing: Column plan layout of the building. Footing plan layout of the building. Beam plan layout of the building. Procedure: 1. First…

1) Aim: Creating templates, inserting text and attributes Custom 1_ title block Custom 2_ title block Procedure: Custom 1_ title block: Create a rectangle of size 66.63mm and 158 mm  Divide it with line for the text box into columns For rows, take offset of 5,10,5,5,8,30,15,15,20,20,10,15 mm. By multiline text,…

Aim: To Create the Kitchen Layout and to Also, use proper dimension techniques to dimension the kitchen layout. Also, insert text wherever required. All dimensions are in mm. Procedure: step 1: units are set to mm limits and limax are also set zoom command is also used Steps for drawing Below Counter Plan Open Auto…

AIM: To Create a layout of the plan and section A of the project in challenges 7 . PROCEDURE:  In the command prompt type units > mm> decimal In the command prompt type limax >100,100 In the command prompt type limits>0,0 In the command prompt type layout > template>Tutorial arch .m   …

  AIM: To create a 3D Furniture element as given in the figure and need to assume dimensions which are missing in the drawing.    INTRODUCTION:- The three dimensional furniture element was drawn in the autocad using the different tools in the autocad. 3D models are widely used anywhere in 3D graphics…

AIM:- To create a 3D isometric view of the given building with plan and elevation.    INTRODUCTION:-  An isometric drawing is a 3D representation of an object, room, building or design on a 2D surface. One of the defining characteristics of an isometric drawing,…

AIM OF THE PROJECT- Creating a 3D rendered model for a Residential Building in AutoCad.   INTRODUCTION- COMMANDS USED FOR DRAWING THE 3D RENDERED VIEW OF BUILDING ARE AS FOLLOWS. -         Extrude- Location: Draw > Modeling > Extrude This AutoCAD 3D Extrude command allows…

1. AIM:- To model a Ceiling from the architecture tab above the walls at the first-floor level.     INTRODUCTION:- The creation of Ceilings within Revit is a very similar process to that of Floors and Roofs- ie you can let Revit do most of the work and “guess” where you want the boundaries…

1. AIM:  Select the type of structure you want to build from one of the three below:        a. Multi-Unit Residential Apartment        b. Office Buildings        c. School. ANS) OFFICE BUILDING   2. AIM :  Assume reasonable assumptions for geographic…

Creating Conceptual mass in REVIT and Creation of a Sinusoidal curve and a Parametric stadium using Dynamo Introduction: Dynamo is an open-source visual programming language for Revit, written by designers and construction professionals. It's a programming language that allows you to type lines of code;  while also…

1. ans. Aim:- Exporting the Revit architecture and structure model to the Navisworks Cache file following the export settings. Tools used:- Revit, Projects, Export option, file menu, 3D view, etc. Navisworks is Used primarily in construction industries to complement 3D design packages (such as Autodesk Revit, and AutoCAD),…

 1.A.  This crack will be formed due to the flexural failure of a beam. The flexural strength, known as modulus of rupture, bend strength, or fracture strength, is a material property, defined as the stress in a material just before it yields in a flexure test. The flexural strength…

1. Differentiate Static analysis and Dynamic analysis by proper representing pictures          STATIC ANALYSIS          DYNAMIC ANALYSIS 1. Load is not variable with time and neglected due to slow applying of load. 1. Load is variable with time due to fast applying…

1 AIM:- To compute Ln, Mn, and Γn for each of the five modes from the given equations.             To calculate the effective modal mass Mn* and the modal mass participating ratio for the 5 modes.             To obtain the base shear…

1. Ans: Symmetry: It is observed that the distribution of mass and stiffness across the plan has good symmetrical aspects. This tends to reduce the horizontal displacements in both of the two horizontal displacements in both of the two Orthogonal Horizontal Directions. It also has very good uniformity also. Redundancy: …

1.   As the structure is more restrained it will be shrinking, expanding, and cracking. There will be more floor shrinkage and expansion in structure A whereas there will be minimum cracks in structures B and C. The shear walls in the structure also decide whether the floor vibration is more or less in the structure…

1. Aim: to model and analyze a 25-storey building with given specifications and to cross-check the parameters as per IS 1893 provisions. Procedure: Open the ETABS software. Click the file menu and choose to create a new model option. After choosing a new model a dialogue box will appear as model initialization. Choose…

AIM: TO MODEL AND ANALYZE MULTIPLE BUILDINGS WITH DIFFERENT FLOOR LEVELS AND DESIGN PARAMETERS USING ETABS SOFTWARE AND COMPARE THE RESULTS TO UNDERSTAND THEIR OVERALL SEISMIC BEHAVIOUR.     INTRODUCTION: The structural configuration of the building plays a major role in determining the overall response during…

1. Aim:- To design the beams in detail from the Etabs.             To provide details of longitudinal and shear reinforcement for the given two continuous beams.             To calculate the value of maximum shear force in any one of the spans in the continuous…

Aim: To Provide details of longitudinal reinforcement for the two columns from the foundation to the terrace level. Step 1: 1) Open a G+4 Etab file 2) Click the Concrete Frame Design tool 3) Select the Display Design Info option 4) Choose design output as Longitudinal Reinforcement Step 2: 1) After Selecting the Longitudinal…

Aim:   To run the analysis and design the RCC shear walls shown in the ETABS model. Step 1: 1) Open the ETABS file 2) After the analysis click Concrete frame design Step 2: 1) Need to check there is any failures occur 2) Click the Shear wall design tool 3) select Display info and choose PM failure  Step…

ANSWER:- Aim:- To model and analyze the G+7 residential building from the given architectural drawings using the ETABS 2018. Introduction:- Engineering software called ETABS is used to analyse and design multi-story buildings. The grid-like geometry specific to this form of construction is taken into account via modelling…

SHALLOW FOUNDATION ISOLATED FOOTING DESIGN Aim:  To create a square footing for a 400x400 column utilizing some of the information, including   The compression axial load for the (1.5 DL + 1.5 LL) load combination is 2000 KN. At a depth of 2 meters below E.G.L., the safe soil carrying capacity is 150…

AIM:- The structural model has to be created and analyzed using the specified building in ETABS 2018 in line with IS 1893 and IS 13920. To create the ground floor frame plan and beam detailing, as well as the pile cap and pile reinforcement details, tie beam linking the pile caps, and column reinforcement sketches. provided…

1. Aim: To simulate the isolated footing offered in the SAFE challenge for week 11 Verify the size, depth, and steel offered based on calculations by analyzing and designing the structure. should use SAFE software to simulate the pile cap. Introduction The finest tool for planning concrete slabs and foundations is CSI…

Q1      1.         Following are the steps needed to upload an a.std file over webmails:        Locate the share option on the introduction screen by opening the STAAD pro program.       Select the option to send mail after clicking the share…

1.     1.  Go to properties, choose to define property, circle, and then give the member's radius before assigning the specified circle to the member you just created.      2.             While creating a model go to the unit system and assign the…

1.     1.  The primary load cases that are to be considered for design are listed below: Dead Load (IS 875: Part I). Live Load (IS 875: Part II). Wind Load (IS 875: Part III). Snow Load (IS 875: Part IV). Seismic Load (IS 1893: 2016).    2.  The bending force only…

1. Design a multi-storey Residential Building located in Bangalore using STAAD Pro Connect Edition. The specification must be as follows: Building floors G + 6 + R Plan dimension B = 25m ,  L = 16m Storey Height h = 3.5m Soil  Hard soil Use Residential Purpose Safe Bearing Capacity 180 kN/m2 Maximum slab thickness…

1. Design a Warehouse Building located in Chennai using STAAD Pro Connect Edition. The specification must be as follows:      Width  30m Length 50m Eave Height 9m Bay spacing 6m Soil type Medium Safe Bearing Capacity 200 kN/m2 Roof slope 1 in 12 Assume suitable sections for structural elements.…