Week 8 - Challenge 1 - Base Bracket Design AIM:- Create the Base Bracket Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model.  CLASS…

Week 8 - Challenge 2 - Switch Bezel Design AIM:- Create the Switch Bezel Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model.  Tooling…

Week 8 - Challenge 3 - Coin Holder Design Aim:-Create the Coin Holder Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model.  Take the Thickness…

Week 8 - Challenge 4 - Bumper Aim:- Create the Bumper Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model.  Take the Thickness of…

Week 8 - Challenge 6 - Core & Cavity Design Aim:- Create the Core and cavity blocks for the switch bezel designed in the earlier challenge.  Tooling Axis   Creation of tooling axis Using the two side walls 1st axis is made by bisecting  the side wall axis   As the 4th wall is not there, an assumption…

Week 9 - Attachment Feature Creation (Ribs & Screw Boss) - Challenge 1 Aim:-Create the rib for the Drill Handle considering the design rules mentioned in the video. Tooling Axis Take a extract of the surface make a point and take line in Y direction to create tooling axis   Class A surface   Class B surface …

Week 9 - Attachment Feature Creation - Challenge 2 Aim:-Create the Dog House for the Door Trim considering the design rules mentioned in the video. Consider the thickness of the part to be 2.5 mm. Class A surface     Tooling Axis Take a point and draw the line in y direction to create a tooling…

Week 9 - Project 1 - Door Trim Lower with Engineering Features Aim:- Create the Door Trim Lower Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis…

Week 9 - Project - A pillar Design with Master Section( there is a ppt attach below ) Class A surface  Class B surface   Class C    final cloesd elemnet with attachment(Dog house)   Sketch iso constraint   Draft analysis for closed element with respect to tooling axis     Draft anaysis…

Week 10- Assembly Workbench Aim:- You will have to create 2 assemblies according to the content covered in the course videos. You will be provided with 2D diagrams of the components and you will have to first create the individual part files and then create a complete assembly of those part files in the assembly workbench.…

Week 11 - Final project Aim:- Development of a Door Trim panel Introduction The door panel is the interface between the interior of the car and the inner workings of the door. Generally the door panel is divided into parts for easy designing like arm rest, map pocket, lower substrate. These require one of the toughest…

AIM:- To prepare a report explaining what is Bench-marking , Compare at least 4 Vehicles and Provide a Preoper conclusion for the report ,suggesting a suitable vehicle among the comparison made. What is Benchmarking ? Benchmarking is defined as the process where you measure the company’s success against the…

Challenge :-Underbody Coating AIM:- To Write a one-pager about Under-Body Coating and its purpose, its types in detail, and its pros and cons. ans:- Underbody coating is a thick cladding (typically made of rubber) that is placed uniformly to the car’s underside. When the automobile is fresh…

Hood design-Week 2 Aim:- Design Hood Outer Panel, Inner Panel and the necessary reinforcements by following the Master Section mentioned with the Design parameters explained in the videos.   Introduction:- Hood is main component of a car at the front portion. It is used to decorate the car & add…

Section Modulus calculation and optimization Aim:- To calculate the section modulus of the previously designed hood for analyzing its strength and also optimizing the design to see the difference in the bending strength of the hood. Higher the section modulus of a structure, the more the resistive it becomes…

  Aim:-   Calculate the Wheel Arch gap at required points and check whether the car passes the European standard.   Fender  Fender is the American English term for the part of an automobile, motorcycle or other vehicle body that frames a wheel well…

Fender Design   Fender  Fender is the American English term for the part of an automobile, motorcycle or other vehicle body that frames a wheel well (the fender underside). Its primary purpose is to prevent sand, mud, rocks, liquids, and other road spray from…

 Roof Design  Aim:- For the Given Roof styling, create an ASSEMBLY by developing the essential flanges for the outer roof with calculation of roof heat distortion and snow load.   Roof strength test This protocol explains how the Insurance Institute for Highway Safety (IIHS) evaluates and rates…

Aim:- Design of backdoor and use the provided styling surface to come up with a back door design, use appropriate design methodologies, and provide the necessary reinforcements and embosses   What is back door of a car? The Back door is typically hinged, but sometimes attached by other mechanisms such as tracks, in…

AIM:- The aim of this project is to model a butterfly valve and to apply GD&T to the different parts of the butterfly valve and the assembly. Objective:      To design of Butterfly Valve in appropriate dimension with the application of GD&T - ASME Y14.5 2009. To assemble all the individual parts of the butterfly valve…