Design and Develop of Hood Objective      To understand the concept, design and develop Hood outer panel, inner…

Objective      To calculate the section modulus of hood design and compare with new section that has an improved section modulus of my hood design and what changes to increase strength. Concept      Section Modulus is a geometric property used to calculate the bending stresses in a structural…

Objective      To calculate the Wheel Arch gap at required points and check whether the car passes the European standard. What is Wheel arc?      The wheel arch is the semicircular part positioned above the wheel of a vehicle. The most important body change was that the…

To design a front fender from the given skin data and the master section provided with Drip mounting, A-pillar, Sill, Bumper and Baffle (splash) Mounts.

Objective      To Design a Roof with its components by following the master section of the front roof rail (at least 1 Front roof rail, two bow roofs, 1 center roof rail and 1 rear roof rail), Perform Draft Analysis for all the parts and to report which includes the curvature study on the roof based…

Objective     To design and develop car backdoor/tailgate from given class A surface styling under industrial standards and also to perform draft analysis along the tooling direction  and need to design reinforcements on inter panel. Class A Surface   What is BackDoor?      It is a BIW component which is attached in back…

Objective      To create the Base Bracket Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model.  The Way of Creating the…

Objective      To create the Switch Bezel Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model.  Given CLASS A SURFACE The…

Objective      To create the Coin Holder Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model.  Given CLASS A SURFACE The…

Objective      To create the Bumper Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model.  Given CLASS A SURFACE The Way…

Given CLASS A SURFACE The Way of Creating the Tooling Axis      Need to take center of the surface for a Tooling axis. So, here i took the bottom face which is meet at all surface in a single point which is easy to create a tooling axis and i extracted that face by using extract command(extract definition…

Given CLASS A SURFACE The Way of Creating the Tooling Axis      Need to take center of the surface for a Tooling axis. So, here i took horizontal line which is easy to make a plane at surface with the help of Plane command(Plane Definition = curve + point(default = middle) plane) as shown in figure…

Given CLASS A SURFACE   The Way of Creating the Tooling Axis for Y-AXIS of the Component      Need to take center of the surface for a Tooling axis. So, here i took the top face which is meet at all surface in a single point which is easy to create a tooling axis and i extracted that face by using…

Given CLASS A SURFACE The Way of Creating the Tooling Axis      Need to take center of the surface for a Tooling axis. So, here i took the bottom face which is meet at all surface in a single point which is easy to create a tooling axis and i extracted that face by using extract command(extract definition…

Given CLASS A SURFACE The Way of Creating the Tooling Axis for Y-AXIS of the Component      Need to take center of the surface for a Tooling axis. So, here i took the master section which is meet at all surface in a single point which is easy to create a tooling axis as shown in figure 1.    …

Introduction      To design and develop CAD model of front door trim panel considering following inputs as like in OEM and tier1 companies. Let's speak about what is front door trim panel, which is  aesthetic for interior look with all comfortable features like arm rest, bottle holder, widow…