MODELLING OF AN AMERICAN CHOPPER   OBJECTIVE:  Main objective of this project is to Create a photo-realistic Conceptual model of an American Chopper using solid works by creating part drawings, converting them to 3D models, assembling the created parts and finally giving it…

Radar Mast:   Radar Mast_Front view: Radar Mast_Side view: Radar Mast_Isometric view: Design Tree_Radar Mast   Yatch Assembly:   Yatch Assembly_Front view Yatch Assembly_Side view Yatch Assembly_Isometric view Design Tree _ Yatch Assembly                                                                                  …

BENCHMARKING: Benchmarking is the practice of comparing business processes and performance metrics to industry bests and best practices from other companies. Dimensions typically measured are quality, time and cost.Also referred to as "best practice benchmarking" or "process benchmarking", this process is used in management…

AIM: Study the underbody coating used in automobile industries. Objectives: Study about underbody coatingStudy about types of underbody coating and its advantages and disadvantages. Procedure: Underbody coating is usually a dense cladding (often based on rubber) applied uniformly to the undercarriage of the automobile.…

Objective Design hood outer panel, inner panel and reinforcements with the given outer hood skin, master section and design parameters.   Introduction The hood or bonnet is the hinged cover over the engine of motor vehicles. Hoods can open to allow access to the engine compartment (or trunk on rear-engine and some mid-engine…

AIM: Section modulus calculation and optimization OBJECTIVE: Use section of the Hood and calculate the section modulus. Vary the section in such a way that new section is an improved version of previous section. THEORY: Section modulus is to find the geometric property for a given cross-section used in the design. Calculate…

WHEEL ARC CHALLENGE OBJECTIVE: The objective of the wheel arc challenge is to calculate the wheel arc area using Siemens NX CAD and to prove whether the given fender of car will pass the European standards. INTRODUCTION : Wheel Arch is the semi-circular part of the fender positioned above the wheel of the vehicle. The…

FENDER DESIGN AIM: To design a  front fender of a car by following the given master section as per the design considerations of OEM. INTRODUCTION : Fender is the american english term for the part of an automobile, motorcycle or other vehicle body that frames a wheel well. Its primary propose is to prevent sand,…

ROOF DESIGN AIM: To design a roof with all the components like front roof rail, rear roof rail, and bow roofs by following the given master sections and the high-quality surface, considering all the design requirements as per the OEM standards. ROOF  An automobile roof or car top is the portion of an automobile that sits…

Unable to upload files below 20 MB   Aim: To design a backdoor of the car on sheet metal using the appropriate design and provided skin data by considering design parameters.   Objective: To design a back door of a car with an inner panel, outer panel and reinforcement for hinges, gas stay, Wiper motor and latch. The inner…

AIM :-To create assemblies of Quick return mechanism and CV joint and to also create 2D drawing of the given assemblies in CATIA. Procedure :-1) Create a all sketch by using positioned sketch command2) Ensure that all the sketches in iso- constrained. Model-1: Quick return mechanism:Parts designed in CATIA:ASSEMBLE…

                       BASE BRACKET PLASTIC COMPONENT DESIGN   Aim :-  To design the Base Bracket plastic component through the given Class-A surface.  Objective :- To create a proper tooling direction. To perform draft analysis of the plastic component.…

                                                                                BUMPER DESIGN    AIM:- Create…

AIM: To Create the Door Handle Component from the given Class-A surface. To Create the tooling axis for the given Class-A Surface meeting the requirements of the draft angle. To Attach B side Features in the component. To perform the Draft analysis on the model.  TOOLS USED: Boundary Join Multiple extract Bisecting…

Attachment Feature Creation (Dog House) AIM: Create the Dog House for the Door Trim considering the design rules INTRODUCTION: DOG HOUSE Dog house is an engineering feature used in plastic design. Dog houses are used as support feature. Sometimes other engineering features like snaps, locators, and screw bosses are mounted…

                                                                                DESIGN AND DRAFT ANALYSIS OF SWITCH BEZEL OBJECTIVE:- The objective of the project is to design the switch bezel and to do a draft analysis for it by creating the required tooling direction with the help of Bisecting method. INTRODUCTION:-…

Door Trim Lower with Engineering Features design heat stakes and the locator's design considering the design rules. AIM: Create the Door Trim Lower Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should be created meeting the draft angle requirements and…

AIM: To create the A Pillar Design with the master section given as the intersection sketch with the Class A surface and create the tooling axis and perform the Draft analysis for the final solid part. Class A  Visible surface is a Class-A surface. It provides the style team's look for the component, which the part…

AIM:- To create a CAD model for door trim panel's parts by considering the given inputs of class A surface along with master section by following the design rules followed in OEM and tier1 companies. Objectives:-   To create individual tooling axis for the parts and perform draft analysis on the class…

                                                                                           …

                                                                                           …

                                                                                           …

                                                                                Wiring harness design in CATIA V5 Aim: Route…

                                                                                           …

                                                             CAR SIDE DOOR WIRING HARNESS DESIGN - PROJECT 1 AIM To route the Wiring harness on given car body front…

                                                                                           …