AIM  : To calculate the concrete mix design for M35 grade concrete with fly ash  introduction: Mix design calculate procedure is the same when either GGBS or fly ash is used , the only change will be specific gravity of the admixture. the specific gravity of the fly ash ranges from 2.1 to 3  whereas…

AIM & INTODUCTION : To sketch a G +1 floor residential plan according to vastu shastra and to list down the names of structural drawing required to be provide to the site  To assume the size of structural elements (column,beam,slab etc) and to calculate the loads from the members as per IS code.   Dimensions of Ground …

Aim:To draw  1.Architectural drawing of a residential building: Plan of a residential building. Elevation of a residential building. Section of a residential building. 2.Structural drawing: column plan layout of the building. Footing plan layout of the building. Beam plan layout of the building. Commands used: Line,Offset,Rectangle,Trim,Extend…

Aim: To create: Template,inserting text and attributes Doors of warehouse and placing it in blocks Electrical legend and making it blocks Different types of door for residential project  Drawing bars,making it as block and making it as a table as bar    Commands used: Block. Insert. Attributes. Field. Rectangle.…

AIM: To Create the kitchen Layout and to Also, use proper dimension techniques to  dimension the kitchen layout.Also,insert text wherever required. All dimensions are in mm. Procedure: Step-1:  units are set to mm Limit and limax are also set  Zoom command is also used Step for drawing below counter plan …

1) Creating a layout of the plan and section the project in challenge 7, using  the template tutorial- mArch.dwt in a scale as given in the figure.Use the  MV command to create the viewport of the size as shown in figure.Also ,use ATTEDIT command to edit the information in the tittle block.Use A1 size for the…

1.AIM       To create a 3D furniture elements using the various commands in auto CAD. INTROUDUTION BY 3D VIEW  The process of creating a mathematical representation of any surface of an object in three dimensions by using special software. A 3D model can even be  represented as a two dimension…

1.Q] Create 3D Isometric view of the building with plan and elevation given. AIM:- To create a 3D isometric view of the given building with plan and elavation. INTROUDUTION:-  An isometric drawing is a 3D representation of an isometric drawing,compared to other types of 3D representation, is that the final image is…

AIM: To create a 3D rendered model for a Residential building in AutoCAD INTROUCTION: The main objective of the project is to understand about to create a plan in 2D, then convert it into 3D using AUTOCAD 3 D, applying materials and  rendering. AutOCAD is primarliy used for  generating 2D sketches.While it is…

1) Based on the project saved from Week 3, proceed from the First Floor Level. Model a Ceiling from the architecture tab above the walls at the first-floor level AIM:- To create the ceilling above the walls at the first floor level. PROCEDURE:-  Initially open the week 3 assignment from the revit software. Then, first…

1) Select the type of structure you want to build from one of the three below:        a. Multi-Unit Residential Apartment        b. Office Buildings        c. School Ans: From above the option of type  of structural to build a building, i need to pick a multi- unit residential Apartment.   2) Assume reasonable assumption…

1) Using Dynamo create a set of sinusoidal points and create a curve and create a surface out of the curve.     Ans)   AIM:-  To create a set sinusoidal points, a curve and a surface out of the curve using dynamo.   PROCEDURE:   Intially , open the architecture template of revit software and go to manage tab. In manage…

1) Use the Architecture/ Structure Project file developed by you in Week 6 to 8. Export the Revit architecture and structure model to Navisworks Cache file following the export settings discussed in class A) AIM:-     To use the architecture/ structural project file developed from week-6-8, export the Revit file to navishworks…

1. 1. Write the steps involved to upload a .std file through web mail? A) Steps innvolved to upload a std file wed mails are as follows; Open the STAAD pro software and locate the share option avaliable on the introduction screen. After clicking on the share button, select send mail option. After clicking on the share…

1. 1. How will you assign Circular section to column? A)   Go to properties in that select define property select circle and  give the radius for the member and assign the defined circle to the  member created     2. How will you assign Unit system to a .std model file? A)         While creating a model go to unit system…

1. 1. State the primary load cases to be considered for design. A)  The primary load cases to be considered for the design are the  Dead load  Live load/ Imposed load  Wind load  Earth quakeload     2. What is One – Way slab? A)  One - way slab The ratio of the longer span to the shorter span is greater than 2 is know…

1. Design a multi-storey Residential Building located in Bangalore using STAAD Pro Connect Edition. The specification must be as follows:      Building floors G + 6 + R Plan dimension B = 25m ,  L = 16m Storey Height h = 3.5m Soil  Hard soil Use Residential Purpose Safe Bearing Capacity 180…

1. Design a Warehouse Building located in Chennai using STAAD Pro Connect Edition. The specification must be as follows:      Width  30m Length 50m Eave Height 9m Bay spacing 6m Soil type Medium Safe Bearing Capacity 200 kN/m2 Roof slope 1 in 12 Assume suitable sections for structural elements.…

AIM: Perform Form- finding and structural analysis structure of multiple masts.   PROCEDURE: RFEM software and input the required settings     Set the units to metric system    Tick  the Form Finding option   Insert the nodes at required loacations    connect the lines with…

1. Summarize the user interface in TSD with the for the following items: -A) Project Work Space : Given design Drawing to study the grids and alinement of column placement  and beam placements.Analysis of tool bar in tekla structural Designer Educational in Home tab to manage the properties to acess the materials SECEN…

Create column properties for different types of pedestal members and model in the grids created as per the assignment 1A) Create column properties for different types of pedestal members and model in the grids created as per the assignement Procedure:  open Tekla Strucure Designer software Create New …

Aim:  To Model of a member roof with cables. The modeling, form-finding and create the cutting patterns to the structure.Procedure: Create a new project and form finding and cutting pattern optionsCreate the nodes for the membrane StructureConnect the lines to the nodesAssign the material as cable to the…

1. Create beam properties for First floor and model the beamsA) Create Beam Porperties for First floor :Go to Home tab click manage properties Create Beam properties required material for modelSelect construction levels of set as  ground floor, first floor first floor snap create beams as required way .…

1(a)Observations:Concrete crused and the reinforcement is exposed.Concrete spalled beyond the reiforcement which may be a sign of rupture.Beam top portion looks safe because of the flange advantage from slab.The crack develops from bottom top means rebar yielding occurs in support bottom only.Answer:Its form of flexural…