Report on Benchmarking OBJECTIVE: Find out the best suited car as per the customer requirements with help of Benchmarking. BENCHMARKING: Benchmarking in automobile…

                                               REPORT ON UNDER-BODY COATING UNDER-BODY COATING:In Indian road conditions, a cars underbody is most prone to corrosion. Underbody coating provides long term…

OBJECTIVE:Design Hood Inner Panel, Outer Panel and the necessary reinforcements by following the Master Section mentioned with the Design parameters. Introduction:The Hood is the hinged cover over the engine of motor vehicles . Hoods can open to allow access to the engine compartment,on rear-engine and some mid-engine…

Objective:Use the section from your Hood design and calculate the section modulus using the formula S= I/y. S = I/y  Where,  S = Section Modulus I = Moment of Inertia y = distance between the neutral axis and the extreme end of the object  Section Modulus: The section modulus (S) is geometry property of…

OBJECTIVE:Calculate the Wheel Arch gap at required points and check whether the car passes the European standard. INTRODUCTION:wheel arch is an arch-shaped cavity in the body of a vehicle.It has two purpose. first,It serves for the safety of pedestrians and other cars because the wheel is situated in the body of a vehicle.…

                                                   Report on FENDER DESIGN OBJECTIVE :The objective is to design an automotive  front side fender using NX-CAD. INTRODUCTION:A fender is the part of a car, truck, motorcycle, or other vehicles that frames or covers a wheel well.Its primary purpose is to prevent sand, mud,…

                                                                            Report on roof design OBJECTIVE:    To create…

                                                             PROJECT REPORT OF BACK_DOOR DESIGN OBJECTIEV:By using the given styling surface to design a automotive back door design, use appropriate design                                     methodologies, and provide the necessary reinforcements and embosses to the backdoor.…

                                                    REPORT ON BASE BRACKET DESIGN Aim: To Create the Base Bracket Plastic component through the given Class-A surface. To begin with, the…

OBJECTIVE: To create the Switch Bezel Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model. Thickness of the component to be 2.5 mm. Software…

Objective:Create the Bumper Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model.  Take the Thickness of the component to be 3 mm.…

OBJECTIVE: To create the rib and screw boss for the door handle considering the design rules for the rib creation and screw boss creation and then perform the draft analysis for class A rib,screw boss and final component. Given: Class A srface.   Software Used:Catia v5 Steps involved while creating Switch Bezel…

OBJECTIVE: To Create the Dog House for the Door Trim considering the design rules mentioned below.  Consider the thickness of the part to be 2.5 mm. "C" is where the doghouse contacts the backside of the surface  Doghouse wall thickness at the intersection of the part wall ( C ) should be…

OBJECTIVE: i. To Create the Door Trim Lower Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model.  ii.Create the Heat…

OBJECTIVE:  To create A pillar Design with Master Section. Follow the Master section to create a flange Follow the master section for thickness and to create the Closed volume. Follow the master section to create Attachment features The thickness of the Plastic to be 2.5 mm Given Input:  A surface…

OBJECTIVE: To create 2 assemblies by using provided 2D diagrams of the components . Steps followed to create assemblies: creation of position sketches of individual parts. converts into 3D all parts after creation of sketches. Assemble all parts using constraints. Use drafting tools to create a 2D drawing of…

OBJECTIVE: To create the a Door Trim panel and its engineering features. INTRODUCTION: The door trim panel is the interior plastic component attached to the sheet metal part of the Door. It ontains engineering features like a doghouse, heat stakes and pushpins to assemble its components. Door trim panel is assembly…

OBJECTIVE: To  work on the modelling, assembly, and drafting of a Butterfly Valve. Using the Siemens NX CAD software. Software Used: NX CAD Parts of Butterfly Valve: Body. Shaft. Disc/Plate. Retainer. Lever. Nut. screw Body: Shaft:   Disc:    Retainer:      Lever:  Nut:        

                                                                         1.Title of the Project:  Nx_casing design using Nx cad      2. Objective: To design a sheet metal casing in industrial manner by using Siemens NX Cad.      3. Introduction: The sheet metal application provides an environment for the design of sheet…

                                                            1.Title-BOX ASSEMBLY                                                                                                                                   2.OBJECTIVE: To design a sheet metal casing in industrial manner by using Siemens NX Cad. 3.INTRODUCTION: The…

                                                            1.Title-Odd_Enclosure                                                                                                                                 2.OBJECTIVE: To design a sheet metal Odd_Enclosure in industrial manner by using Siemens NX Cad. 3.INTRODUCTION: The…

                                                      1.Title of the Project:  Nx_Bracket using Nx cad 2. Objective: To design a sheet metal Bracket in industrial manner by using Siemens NX Cad. 3.Introduction: The sheet metal application provides an environment for the design of sheet metal parts used in Machinery, Automotive,Aerospace…