Design M35 Grade concrete with Fly ash Type of aggregate= Crushed angular aggregate  Type of cement is 53 grade conforming to IS8112 Size of aggregate= 20mm   Specific gravity oc cement=3.15 Workability: 100 mm slump Exposure= Severe Specific Gravity of fly ash= 2.2 (IS 3812 part 1) Specific Gravity pf CA and…

AIM: To provide a residential plan of G+1 floor according to Vastu Shastra, and the structural drawings required and load calculation of the Residential Structure. 1. Architectural Drawing Architectural drawing can be termed as the mother drawing for all the other drawings used for construction. It contains all the details…

1) AIM: To provide the given diagram in P-1 by AutoCAD, and draw the diagram with following Dimensions using Imperial Template and Decimal Unit. Procedure:  Command Line in the command box/ From menu bar line can be chosen. 1st point as 2,1 2nd point as 8,1 3rd point as 8,2 4th point as 3,2 5th point as 3,6 6th…

1) Aim: To construct/draw the C.S of load bearing wall on spread footing using AutoCad. Procedure: Setting the units into meter. Cronstructing the structure by the given measurements. 1st point as 2,1 Creating the lower footing according to the measurements of .90 m width and .25 m height. Plotting a ceneter line of the…

1) AIM: To draw DECIMAL Diagram with help of AutoCAD. Procedure: Switching unit to decimal Take starting point as 2,1 2nd point as @3<0 3rd point as @2.12<45 4th point as @2.83<135 5th point as @2<180 Close Then taking the point at distance 1 from the center and drawing the circle with Dia 1.20 Then taking…

1) Aim: To prepare the plan diagram using AutoCAD Procedure: Line command Unit command Ast unit to architectual Ds command Set units accordingly Line command and create the outer borders of the plan Offset 9.0" mm and draw the inner lines Offset 4.5" mm for single wall Put the dimansions accordingly. Result: Thus, the…

1) Aim: To prepare the following task using Autocad   Result: The following is created Via AutoCAD.   2) Aim: To prepare the following task using Autocad Result: The following is created Via AutoCAD.   3) Aim: To prepare the following task using Autocad Result: The following is created Via AutoCAD.  …

1) AIM : To prepare the wardrobe section, elevation, palan details using AutoCAD. STEPS/PROCEDURE:   Result: Thus, the final output of Wardrobe details is provided using AutoCad.   2)Aim: To prepare the FLOOR plan using AutoCAD. STEPS/PROCEDURE:         Result: Thus, the final output of Floor…

Aim: To create Plans Sections as shown in  figure using AutoCAD. Procedure for 1st,2nd and 3rd floor plan: Procedure for Section A-A: Procedure for Section B-B: Result: Thus, the following plan and sections are made with the help of AutoCAD.

Aim: Creating an Architectural Plan for 60'x20' plot size. and provide structural drawing.       Result: Thus, the plan section elevation and beam column and footing details are provided for 60'x20' plot size area.

1) AIM: To create the following drawing of given dimension and convert it into a block. Procedure: Draw the title box of given dimension. Command block Name them as Custom1_titleblock and Custom2_titleblock, respectively. Select the object to be converted as block. Select pick point and the block is created. RESULT:…

1) Aim: To create the given diagarm as proved and provide hatch at the required places.     2)Aim: To create the given diagarm as proved and provide hatch at the required places.     3)Aim: To create the given diagarm as proved and provide hatch at the required places.    

1)AIM: To prepare the current drawing and take a print on A1 size paper as per scale Steps:   Result: Thus, the current drawing is printed on A1 size paper.   2)AIM: To prepare the current drawing and take a print on A4 size paper as per scale Steps:         Result: Thus, the current drawing…

Challenge:1 Aim: To draw the 3D Isometric view of the building with the given elevation and plan details. Introduction: A plan view of both the walls of the building, elevation details from both sides along with the necessary dimensions are provided which is to be converted into a 3D model. 2 window openings with its frame…

Task: 1  Aim: To draw a 3D representation of a furniture element assuming certain dimensions and as per the given details. Introduction: A 3D view of the furniture element is provided with few dimensions like its height which is 2’-6”, its width 3’, its thickness i.e. 2”. Other details such…