GATE Production and Industrial Engineering (PI): General Engineering (materials, iron-carbon diagram, strength of materials, theory of machines, machine design, thermodynamics, fluid mechanics, heat transfer), previous-year questions solved, part 2

Part 2 of 2 of the General Engineering hub: 14 more official GATE PI questions on theory of machines and machine design and thermal and fluids engineering, each solved step by step and checked against the official answer key. Part 1 covers engineering materials and engineering mechanics and strength of materials.

Questions from official GATE PI papers (IISc Bengaluru 2024, IIT Roorkee 2025, IIT Guwahati 2026); solutions by Skill-Lync. · Updated 20 Nov 2026 · 14 of 30 questions on this page

GATE 2024 · PI · Q.34NAT · 1 markTheory of machines and machine design

Offset slider-crank with crank l, rod 3l and offset l, l = 10 cm: stroke of the slider in cm

An offset slider-crank mechanism is shown in the figure. If the length cm, then the stroke length (in cm) of the slider is __________ . (Rounded off to 1 decimal place)
Offset slider-crank: crank of length l turning about a fixed pivot, connecting rod of length 3l, slider moving on a line a distance l above the crank pivotll3l

Answer: 21.4 Official key: 21.3 to 21.5

  1. The stroke is the distance between the two extreme positions of the slider. They occur when the crank and the connecting rod are in line: fully stretched (crank and rod pointing the same way) and fully folded (crank pointing back along the rod).
  2. The slider centre line is a distance cm above the crank pivot. With the crank cm and the rod cm, the horizontal distance from the pivot to the slider is in each extreme.
  3. Stretched: line length cm, so cm.
  4. Folded: line length cm, so cm.
  5. Stroke 21.4 cm, inside the key range 21.3 to 21.5.

Check: the slider position was computed for every 0.01 degree of crank angle from , and the largest minus the smallest position was 21.41 cm, the same as the in-line result. Trap: using the no-offset stroke of cm; with an offset the stroke is a little larger than for a rod of this length.

Where this shows up in industry

Offset slider-cranks are used in quick-return shapers, in some presses and in compressor and engine layouts where the slider line does not pass through the crank pivot. The offset makes the forward and return strokes unequal in time, which is useful when the working stroke should be slow and the return fast.

GATE 2024 · PI · Q.51NAT · 2 marksTheory of machines and machine design

Flat belt on a 20 cm radius pulley, 6.283 kW at 600 rpm, mu 0.3: minimum tightening force F in kN

A flat belt drive with pulley of cm radius is designed to transmit 6.283 kW power at 600 RPM. In the figure, is the corresponding torque. If the coefficient of static friction between the belt and the pulley is 0.3, then the minimum value of the tightening force (in kN) required to prevent the belt slip is __________ . (Rounded off to 2 decimal places)
Flat belt on a pulley of radius r: the belt tensions T1 (top) and T2 (bottom) both pull to the left over a half wrap, the shaft bearing force F points to the right, and torque tau acts anticlockwiseT1T2Frτ

Answer: 1.14 Official key: 1.13 to 1.15

  1. Power is torque times angular speed, . With rpm, rad/s, so N-m.
  2. The torque is the difference of the belt tensions times the radius: , so N.
  3. At the point of slipping, the belt friction (capstan) law gives . In the figure both spans leave horizontally to the left, so the wrap angle is half a turn, : .
  4. N and N.
  5. Both tensions pull on the pulley to the left, so the bearing force that holds it must balance their sum: N 1.14 kN, inside the key range 1.13 to 1.15.

Check: the numbers were recomputed in code from power and speed. Trap: using kN as the force; that is the force that makes the torque, while the force on the shaft is the sum of the tensions.

Where this shows up in industry

Belt conveyors and flat-belt drives on machine tools set their initial tension so that the slack side never goes slack and the belt never slips on the pulley. The shaft and bearing must carry the sum of both tensions, not their difference.

GATE 2025 · PI · Q.57NAT · 2 marksTheory of machines and machine design

Resultant shear force on the middle bolt of a three-bolt eccentric joint carrying 12 kN

A steel plate is fastened to a channel using three identical bolts as shown in the figure. The bolts are made of carbon steel of permissible yield strength in shear as 400 N/mm. The plate is subjected to a force of 12 kN. Neglect the weight of the plate. The magnitude of the resultant shear force (in N) on bolt 2 is________. (Answer in integer)
Steel plate bolted to a channel with three bolts 1, 2 and 3 in a row; the 12 kN load acts 300 mm beyond the channel edge on the bolt line; bolt spacings 50, 100, 100 and 50 mm12312 kN5010010050300All dimensions are in mm.

Answer: 4000 Official key: 4000 to 4000

  1. An eccentrically loaded bolt group is solved by moving the load to the centroid of the bolts. The load then becomes the same force plus a twisting moment . Each bolt carries a direct shear (equal share) and a torsional shear, perpendicular to its radius from the centroid, proportional to that radius.
  2. The three bolts are in a row, so the centroid is bolt 2. The load is mm from it, so N mm. Direct shear on each bolt: N.
  3. With mm and : . Torsional shear on a bolt , so for bolts 1 and 3 it is N, and for bolt 2 it is zero because it sits on the centroid.
  4. Bolt 2 has no torsional shear, so its resultant is the direct shear alone: 4000 N. For comparison, bolt 3 (nearer the load) carries N, the critical bolt, and bolt 1 carries N. The three bolt forces add up to 12 000 N and balance the moment.

Trap: the 400 N/mm strength in shear is not needed for this answer; it matters only if the next step is the bolt diameter, which is set by bolt 3.

Where this shows up in industry

Brackets, lifting lugs and fixture plates bolted off-centre to a frame are checked with this direct plus torsional shear method. The bolt farthest from the group centroid is the one that governs the size.

GATE 2026 · PI · Q.20MCQ · 1 markTheory of machines and machine design

Name of the tapered sunk key that prevents relative axial motion between shaft and hub

An engineering student is fabricating a setup and needs a key for connecting a shaft to the hub of a rotating machine element. The student uses a sunk key which is tapered and prevents relative axial motion.

Which ONE of the following keys did the student most likely use?

  1. (A)Saddle key
  2. (B)Woodruff key
  3. (C)Feather key
  4. (D)Gib-head key

Answer: (D) Official key: D

  1. Rule: a key transmits torque between shaft and hub. Sort keys by three properties: is it sunk into the shaft, is it tapered, and does it lock the hub against axial motion.
  2. (A) Saddle key: sits in a keyway in the hub only and rests on the shaft, so it is not a sunk key and holds by friction. Out.
  3. (B) Woodruff key: semicircular, sunk in a circular seat, parallel sides, not tapered. Out. (C) Feather key: sunk and parallel, fixed to one part so the hub can slide along the shaft, so it allows axial motion. Out.
  4. (D) Gib-head key: sunk and tapered (usually 1 in 100) with a head so it can be driven in and drawn out. The taper wedges it tight and locks the hub axially. It meets all three conditions, so the answer is (D).

Trap: feather and gib-head keys are both sunk keys, but the feather key is parallel and lets the hub slide, which is the opposite of the clue. We stored the three properties for each key and tested every option: only (D) passes all three.

Where this shows up in industry

Gib-head keys are used where a hub must be locked on a shaft and later pulled out from one side, such as large pulleys, flywheels and coupling hubs on press and mill drives, while feather keys are used on splined or sliding gear and clutch hubs.

GATE 2026 · PI · Q.56NAT · 2 marksTheory of machines and machine design

Module of a 20 tooth spur pinion transmitting 95 N-m with the Lewis equation and width 10 times module

A custom pinion, with a width equal to 10 times the module, has 20 full depth teeth and a pressure angle of 20° is being designed. It should transmit a torque of 95 N-m to a corresponding spur gear.

Considering the safe bending stress to be 180 MPa and form factor to be 0.342, the module of the pinion is ______ mm (rounded off to one decimal place).

Note: The Lewis equation gives the tangential force as , where is the safe bending stress, the width, the form factor, and the module.

Answer: 2.5 Official key: 2.4 to 2.6

  1. Rule: the load on a spur gear tooth is the tangential force at the pitch circle, with pitch diameter . The Lewis equation gives the most the tooth can carry in bending, . Design sets the two equal.
  2. Work in N and mm: , , so N.
  3. Strength: , so N.
  4. Equate: , so and 2.5 mm. The tangential force is then 3816 N.

Check: 2.5 mm is also a standard module, so the pinion can be made with it. Common slips: forgetting the factor 2 in gives 1.98 mm; leaving the torque in N-m instead of N-mm gives 0.25 mm. We solved the equation by bisection on the gap between strength and load, and it agrees with the cube root.

Where this shows up in industry

Gear designers use the Lewis equation as the first sizing step for the pinion in a press drive, conveyor gearbox or machine tool feed drive, then check the result against wear (surface fatigue) and the standard module series before drawing the part.

GATE 2024 · PI · Q.14MCQ · 1 markThermal and fluids engineering

Heat loss per unit length of a thin insulated wire as the sleeve thickness t grows

A thin copper wire carries electric current and is insulated by putting a sleeve, of thickness , over it. In steady state conditions, the rate of heat loss from the insulated wire per unit length is . Which of the following is TRUE?
  1. (A) increases monotonically with .
  2. (B) decreases monotonically with .
  3. (C) first increases with increase in , and then it decreases with further increase in .
  4. (D) first decreases with increase in , and then it increases with further increase in .

Answer: (C) Official key: C

  1. For a cylinder the heat loss per unit length from a surface at to surroundings at is , the sum of a conduction resistance in the sleeve (conductivity ) and a convection resistance at the outer surface (coefficient ). Here is the wire radius and .
  2. A thicker sleeve raises the conduction term (it grows as ) but lowers the convection term (it falls as , more outer area to shed heat).
  3. Setting the derivative of the total resistance to zero gives the critical radius of insulation . For the convection term falls faster than the conduction term rises, so rises; beyond it falls.
  4. The wire is thin, so its radius is below . Adding a sleeve first increases until , and then decreases: (C).

Check: for a wire of 0.5 mm radius, a sleeve with W/m-K and W/m-K, mm. Scanning from 0 to 80 mm at an 80 K temperature difference, starts at 2.5 W/m, peaks at 21.4 W/m when = 20.0 mm (the critical radius) and falls to 18.9 W/m; only option (C) describes that curve. Trap: assuming that insulation always reduces heat loss, which is true only once .

Where this shows up in industry

Thin electrical wire, cable and small tube insulation is chosen with the critical radius in mind: a thin sleeve can make a hot small conductor run cooler, which is why enamel and thin PVC coatings are used on heating and winding wire. For large steam pipes the outer radius is far above the critical radius, so every added layer of insulation cuts heat loss.

GATE 2024 · PI · Q.48NAT · 2 marksThermal and fluids engineering

Irrigation pump hose of 5.05 cm at 8 kg/s and 50 kPa: nozzle diameter in cm for atmospheric exit pressure

An irrigation pump is used to draw water from a pond. One end of a 5.05 cm diameter hose pipe is connected to the outlet of the pump at 1.02 m below the surface level, and just after the pump, the static gauge pressure and flow rate of the water are 50 kPa and 8 kg/s, respectively. The pumped water is discharged at the ground level through a nozzle. Assume that the flow through the hose pipe and nozzle is steady and laminar, and frictional and viscous losses are negligible. The density of water is 1000 kg/m and the acceleration due to gravity is 9.81 m/s. If the static pressure at the nose/exit of the nozzle just reduces to atmospheric pressure then the nose diameter (in cm) of the nozzle is ____________ . (Rounded off to 2 decimal places)

Answer: 3.22 Official key: 3.20 to 3.25

  1. Continuity for steady incompressible flow: mass flow is the same everywhere. Bernoulli (no losses): is the same along the line. The pond surface level (ground level) is taken as , so the pump outlet is at m and the nozzle exit at .
  2. Hose area m. Speed m/s.
  3. At the nozzle exit the gauge pressure is zero. Total head at the pump outlet: m. This equals at the exit, so m/s.
  4. Continuity at the nozzle: m, so 3.22 cm, inside the key range 3.20 to 3.25.

Check: the three steps were computed in code with the paper's values and gave 3.225 cm. The nozzle is smaller than the hose (5.05 cm), as it must be for the water to speed up from 3.99 to 9.79 m/s. Trap: leaving out the 1.02 m height of the pump below the surface gives a nozzle diameter of 3.08 cm, outside the key.

Where this shows up in industry

Pump duty points are set with exactly this balance of pressure head, velocity head and height. The same relation sizes spray nozzles for coolant, wash-down and irrigation lines so that a given exit speed is reached at the pump pressure available.

GATE 2024 · PI · Q.49NAT · 2 marksThermal and fluids engineering

Air-standard Otto cycle, 1.02 MJ/kg heat added, efficiency 50 %, gamma 4/3: maximum pressure in MPa

In an air-standard Otto cycle, the pressure and temperature of air just before the compression stroke are 200 kPa and 26.85 °C, respectively. The combustion process is assumed to be a constant volume process, where 1.02 MJ/kg heat is added. The cycle efficiency is 50%. The adiabatic index and specific heat at constant volume can be considered to be constant during the process (corresponding values taken at the mean cycle temperature).

Assuming that the ideal gas law is applicable, and kJ/kg-K, the maximum pressure (in MPa) reached during the cycle is ______________ . (Rounded off to 1 decimal place)

Answer: 9.6 Official key: 9.5 to 9.7

  1. The Otto cycle has isentropic compression (1 to 2), constant volume heat addition (2 to 3), isentropic expansion (3 to 4) and constant volume heat rejection (4 to 1). The highest pressure is at state 3, at the end of heat addition.
  2. Compression ratio from the efficiency: , so , and .
  3. State 1: K, kPa. Isentropic compression: K and kPa.
  4. Heat added at constant volume: , so K.
  5. At constant volume, : kPa 9.6 MPa.

Check: expansion to state 4 gives K, heat rejected kJ/kg, and net work kJ/kg is half of the heat added, which confirms the 50 % efficiency. Trap: using K or the Celsius value in the gas relations; temperatures must be absolute.

Where this shows up in industry

Peak cylinder pressure from an Otto-cycle estimate sizes the cylinder head, head bolts and gasket in spark-ignition engines and gas engines. A higher compression ratio raises efficiency but also the peak pressure and the knock risk, so the two are balanced in the design.

GATE 2025 · PI · Q.28MCQ · 1 markThermal and fluids engineering

Type of process in which heat is added in the ideal Diesel cycle

For an ideal Diesel cycle, the heat addition is an
  1. (A)isobaric process
  2. (B)isothermal process
  3. (C)isochoric process
  4. (D)isentropic process

Answer: (A) Official key: A

  1. The ideal air-standard Diesel cycle has four processes: 1-2 isentropic compression, 2-3 heat addition, 3-4 isentropic expansion, 4-1 heat rejection at constant volume.
  2. Fuel is injected near the end of compression and burns as the piston starts to move down. The cylinder volume grows while the fuel burns, which holds the pressure about constant. So the heat addition 2-3 is at constant pressure, an isobaric process: .
  3. Check with , compression ratio 18 and cut-off ratio 2 (start 300 K, 100 kPa): K and K, so the temperature rises and the volume doubles, but the pressure stays at 5720 kPa. The entropy increases (it is not isentropic) and the process is not isothermal or isochoric.
  4. The heat is added at constant pressure, so the answer is (A).

Trap: constant-volume heat addition belongs to the Otto cycle (petrol engine). The Diesel cycle adds heat at constant pressure and rejects it at constant volume.

Where this shows up in industry

Diesel engines in generator sets and trucks are analysed with this cycle, and its constant-pressure burn is why they run at high compression ratios without knock. Plant engineers use it to compare fuel use between engines.

GATE 2025 · PI · Q.64NAT · 2 marksThermal and fluids engineering

Centre-line velocity of laminar pipe flow, 10 cm diameter, 10 m long, 0.2 Pa pressure drop

Water flows through a smooth circular pipe of diameter 10 cm and length 10 m. The pressure drop across the length of the pipe is 0.2 Pa. Kinematic viscosity and density of water are m/s and 1000 kg/m, respectively. Assuming laminar and fully developed flow throughout the pipe, the velocity of water (in mm/s) at the center of the pipe is __________. (Rounded off to one decimal place)

Answer: 12.5 Official key: 12.3 to 12.7

  1. For laminar, fully developed flow in a circular pipe (Hagen-Poiseuille), a force balance on a fluid cylinder gives a parabolic velocity profile . The velocity is largest on the axis, , and is twice the mean velocity.
  2. Dynamic viscosity Pa s. Radius m. Pressure gradient Pa/m.
  3. m/s mm/s.
  4. Regime check: the mean velocity is mm/s, so , far below 2300. Laminar flow is consistent with the assumption, and the friction factor form returns the same 0.2 Pa.

Trap: using the diameter 0.1 m in place of the radius gives 50.0 mm/s (four times too big), and giving the mean velocity (6.25 mm/s) misses the question, which asks for the centre.

Where this shows up in industry

Laminar pipe flow formulas apply to oil lines, lubrication passages and coolant hoses at low speed and high viscosity. Hydraulic and lubrication designers use them to find the pressure needed for a given flow.

GATE 2025 · PI · Q.65NAT · 2 marksThermal and fluids engineering

Right-hand surface temperature of a 20 cm wall at 25 C on the left and in 50 C air on the right

The left-hand side of a 20 cm thick wall is maintained at 25 °C. The right-hand side of the wall is exposed to hot air at 50 °C. There is no heat generation inside the wall and its thermal conductivity is 100 W/m·K. The convective heat transfer coefficient is 50 W/m·K. Under steady state condition, the temperature (in °C) of the right-hand side surface of the wall is________. (Rounded off to one decimal place)

Answer: 27.3 Official key: 27.1 to 27.5

  1. In steady state with no heat generation, the same heat flux (W/m) passes through every layer. Heat flows from the hot air, through the convection film on the right surface, then through the wall by conduction to the cold left face. These are resistances in series.
  2. Per unit area: conduction resistance mK/W, convection resistance mK/W. Total mK/W.
  3. Heat flux W/m.
  4. The air-to-surface drop is K, so the right-hand surface is at C. Check from the wall side: C.

Trap: convert 20 cm to 0.2 m. Leaving it as 20 in the conduction term gives 47.7 C. The surface sits close to the cold side because the wall (high ) conducts far better than the air film passes heat.

Where this shows up in industry

Furnace walls, oven doors and heat-treatment shop panels are checked with series resistances like this to find the outer surface temperature for safety and insulation choice. A high-conductivity wall with a poor air film runs close to the coolant-side temperature.

GATE 2026 · PI · Q.29MSQ · 1 markThermal and fluids engineering

Which processes of the Carnot cycle on the p-V diagram are isentropic

Which ONE or MORE among the following processes of the Carnot cycle is/are isentropic?

Note: Figure is not to scale.

Carnot cycle on a pressure against volume diagram: 1 to 2, 2 to 3, 3 to 4, 4 to 1 in the direction of the arrowsPV1234Figure is not to scale
  1. (A)1-2
  2. (B)2-3
  3. (C)3-4
  4. (D)4-1

Answer: (B) and (D) Official key: B;D

  1. Rule: a Carnot cycle has two reversible isothermal processes (heat in at the high temperature, heat out at the low temperature) and two reversible adiabatic processes. A reversible adiabatic process has no heat transfer, so : it is isentropic. An isothermal process exchanges heat, so its entropy changes.
  2. Read the figure: on a p-V diagram an adiabat is steeper than an isotherm. The two gentle curves are 1-2 (at the top, the high temperature) and 3-4 (at the bottom, the low temperature): isothermal. The two steep curves are 2-3 (expansion, temperature falls) and 4-1 (compression, temperature rises): adiabatic.
  3. Check with an ideal gas (, K, K) through : 1-2 gives 0.1989, 2-3 gives 0.0000, 3-4 gives -0.1989, 4-1 gives 0.0000 kJ/kg-K. The slope exponent of is 1.00, 1.40, 1.00, 1.40: 1 for the isotherms, 1.4 for the adiabats.
  4. The isentropic processes are 2-3 and 4-1, so the answer is (B) and (D).

Trap: the two isotherms are the ones with heat flow, so they carry the entropy change (up on 1-2, down on 3-4 by the same amount). Isentropic does not mean isothermal: on 2-3 and 4-1 the temperature does change.

Where this shows up in industry

The Carnot cycle is the upper limit of efficiency for any heat engine or refrigerator working between two temperatures, so it is the yardstick for steam plant, compressors, chillers and engine test results.

GATE 2026 · PI · Q.43MCQ · 2 marksThermal and fluids engineering

Capillary rise in a 2.5 mm glass tube with surface tension 0.1 N/m and zero contact angle

A glass tube of 2.5 mm diameter is immersed vertically in a fluid.

Assume contact angle is zero. The surface tension of the fluid is 0.1 N/m, density of the fluid is 1000 kg/m3 and acceleration due to gravity is 10 m/s2.

The approximate capillary rise is ______ mm.

  1. (A)2
  2. (B)8
  3. (C)16
  4. (D)32

Answer: (C) Official key: C

  1. Rule: capillary rise balances two forces. Surface tension pulls the liquid up around the circumference of the tube: . The weight of the raised column pulls down: .
  2. Equate and solve: .
  3. Put the numbers in SI units: N/m, so , N/m, m. Then m mm.
  4. The answer is (C) 16 mm.

Trap: the factor 4 is for the diameter. Putting the radius into the form gives 32 mm, and using (the wrong factor) gives 8 mm. We computed the height both from the force balance and from the formula and tested each option: only 16 mm matches.

Where this shows up in industry

Capillary rise explains how cutting fluid and flux wick into narrow gaps, why liquid manometers and level gauges in thin glass tubes read high, and how brazing filler and penetrant dye are drawn into joints and cracks.

From GATE prep to a manufacturing, design or plant engineering career

Talk to a counsellor.

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.

Talk to a career counsellor

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.