Strength of Materials cover
Interactive book · Semester 3 or 4

Strength of Materials

Drag, slide and break things to learn how parts carry load

Nine chapters, 13 interactives, few words. Every chapter is mapped to the Anna University, VTU, SPPU, Mumbai University and KTU units it covers, so you can revise exactly what your exam asks.

  • AUCE3491Strength of Materials
  • VTUBME301Mechanics of Materials
  • SPPU202041Solid Mechanics
  • MUMEC302 / 2403112Strength of Materials
  • KTUPCMET302Mechanics of Solids

By Skill-Lync · Updated 15 Nov 2026 · 9 chapters · 13 interactives · free, no sign-up

Chapter 1

Stress, strain and elastic constants

Which syllabus covers thisAU CE3491 Unit IVTU BME301 Module 1SPPU 202041 Unit IMU MEC302 Module 1KTU PCMET302 Module 1

What are stress and strain?

Stress is internal force per unit area, , in N/mm² (MPa). Strain is the change in length per unit original length, , with no units. Within the elastic limit the two are proportional, (Hooke's law), where is Young's modulus.

A steel bar stretching under an axial load: interactive loads as you scroll

What does a stress-strain curve tell you about a material?

Pulling a specimen to failure gives its whole story: a straight elastic line (slope ), yielding where it starts to deform permanently, strain hardening up to the ultimate strength, then necking and fracture. Ductile steel stretches a lot before breaking; cast iron snaps with almost no warning.

Stress-strain curve explorer: interactive loads as you scroll

How are E, G, K and Poisson's ratio related?

Stretch a bar and it also gets thinner: lateral strain axial strain, where is Poisson's ratio (about 0.3 for steel). Only two elastic constants are independent for an isotropic material. For steel, GPa gives GPa and GPa.

How do you analyse compound bars and bars with changing cross-sections?

A bar made of segments in series carries the same load in each, so the extensions add: . In a compound bar, such as a steel core inside a copper tube, the materials stretch together: their strains are equal while the load splits in proportion to . The stiffer material carries more stress.

Why does a bar fixed between two walls get stressed when it is heated?

A free bar simply expands by and stays stress-free. Fix both ends and that expansion is prevented, so the walls squeeze the bar by exactly that amount: . For steel, a 40 °C rise gives 96 MPa of compression, whatever the bar's length or area.

Thermal stress in a bar between two walls: interactive loads as you scroll
Predict, then check

Two steel bars, one 1 m and one 3 m long, are both fixed between walls and heated by 40 °C. Which carries more thermal stress?

Worked examples

Steel rod in tension · mm, m, kN, GPa,
  1. Lateral strain , so shrinks by

Answer: MPa, mm longer, diameter 0.0048 mm smaller

Rail between fixed ends · Steel, , GPa, temperature rises by 40 °C, ends fully restrained
  1. Free expansion per metre
  2. Restrained, so
  3. (compressive)

Answer: 96 MPa compression, independent of the rail's length

Steel core in a copper tube · Steel mm², GPa; copper mm², GPa; same length, kN shared
  1. Equal strain: , so
  2. Equilibrium:
  3. , so and

Answer: Steel 100 MPa, copper 50 MPa

Chapter 2

Principal stresses and Mohr's circle

Which syllabus covers thisAU CE3491 Unit IVTU BME301 Module 2SPPU 202041 Unit VMU MEC302 Module 1KTU PCMET302 Module 4

Why does the stress change when you look at a plane at an angle?

The same loaded point carries different normal and shear stresses on differently oriented planes. Rotate the small element by and the stresses on its faces follow the transformation equations. At one angle the shear vanishes: those faces are the principal planes, and their normal stresses and are the largest and smallest anywhere.

Mohr's circle with a rotating stress element: interactive loads as you scroll

How do you draw Mohr's circle?

Plot point X at and point Y at . The line XY is a diameter; its midpoint is the centre. Rotating the element by moves the point by round the circle. The circle crosses the axis at and , and its radius is the maximum in-plane shear stress.

Which theory of failure should you use?

For ductile metals, compare an equivalent stress with the yield strength: von Mises (distortion energy) matches tests best; Tresca (maximum shear) is slightly more conservative. For brittle materials such as cast iron, the maximum principal stress theory is used. FEA tools report von Mises stress for exactly this reason.

Predict, then check

An element has MPa, MPa and no shear. What is the maximum shear stress on any plane?

Worked examples

Principal stresses of a 2-D stress state · MPa, MPa, MPa
  1. Centre
  2. Radius
  3. ,

Answer: MPa, MPa, MPa at

Is it safe? von Mises vs Tresca · The same element, steel with yield strength 250 MPa
  1. von Mises:
  2. Tresca:
  3. Factor of safety (von Mises)

Answer: Safe: factor of safety 2.37 by von Mises, 2.14 by Tresca

Chapter 3

Shear force and bending moment diagrams

Which syllabus covers thisAU CE3491 Unit IIVTU BME301 Module 3SPPU 202041 Unit IIMU MEC302 Module 2KTU PCMET302 Module 2

What are shear force and bending moment?

Cut a beam anywhere: the shear force is the sum of vertical forces on one side of the cut, and the bending moment is the sum of their moments about the cut. Plotting and along the beam gives the SFD and BMD, and the peak of the BMD is what the beam must be designed for.

Shear force and bending moment diagram builder: interactive loads as you scroll

How are load, shear force and bending moment related?

The slope of the SFD is the (negative) load and the slope of the BMD is the shear. So under a UDL the SFD is a sloping line and the BMD a parabola; under point loads the SFD jumps and the BMD has straight segments. The bending moment is maximum wherever the shear force crosses zero.

What is a point of contraflexure?

A point where the bending moment changes sign, from sagging to hogging ( away from the supports). It appears in overhanging and continuous beams. Engineers place joints and splices there because the bending moment is zero.

Predict, then check

A simply supported beam carries one point load. Where is the bending moment largest?

Worked examples

Simply supported beam, point load · m, kN at 2 m from A
  1. Moments about A: , so kN
  2. kN
  3. kN from A to the load, then kN
  4. kN·m, under the load

Answer: kN, kN, kN·m

Cantilever with a UDL · m, kN/m
  1. Total load kN, acting at 1.5 m
  2. Shear at the fixed end kN
  3. Moment at the fixed end kN·m (hogging)

Answer: kN, kN·m at the fixed end, both zero at the free end

Simply supported beam, UDL · m, kN/m
  1. Each reaction kN
  2. kN·m at mid-span

Answer: kN·m at mid-span

Chapter 4

Bending and shear stresses in beams

Which syllabus covers thisAU CE3491 Unit IIVTU BME301 Module 4SPPU 202041 Unit IIIMU MEC302 Module 3KTU PCMET302 Module 3

How is bending stress distributed across a beam?

Bending stress varies linearly with distance from the neutral axis: zero at the neutral axis, maximum at the outer fibres, compressive on one side and tensile on the other. The bending equation gives , where is the section modulus.

Bending stress across a beam section: interactive loads as you scroll

How do you find the moment of inertia of a built-up section?

Find the centroid first, then add each part's own moment of inertia and its area times the square of its distance from the centroid (the parallel axis theorem). For an unsymmetrical section such as a T, the neutral axis is not at mid-depth, so the top and bottom fibres have different section moduli.

Why are I-sections used for beams?

Bending stress is largest far from the neutral axis, so material placed there works hardest. An I-section puts most of its area in the flanges, giving a high section modulus for its weight. ISMB 200 (100 × 200 mm overall) has about a sixth of the area, and so the weight, of a solid 100 × 200 mm rectangle, yet a third of its section modulus.

What is a flitched beam and how is it analysed?

A flitched beam bolts steel plates to a timber beam so the two bend together. Convert it to an equivalent section of one material using the modular ratio : the steel's width is multiplied by . At any depth the steel stress is times the timber stress, so both limits are checked. The same idea is used for reinforced concrete.

Where is shear stress maximum in a beam section?

Shear stress is zero at the top and bottom faces and maximum at the neutral axis. For a rectangle ; for a circle . In an I-section the web carries almost all the shear, which is why web thickness is checked for shear.

Shear stress distribution across a beam section: interactive loads as you scroll
Predict, then check

You double the depth of a rectangular beam and keep its width. By how much does its bending strength (section modulus) increase?

Worked examples

Rectangular beam in bending · mm, mm, kN·m

Answer: MPa (compression on top, tension at the bottom for sagging)

Shear stress in the same beam · kN
  1. , at the neutral axis

Answer: MPa

T-section: centroid, I and section moduli · Flange 100 × 20 mm on top of a web 20 × 80 mm (overall depth 100 mm)
  1. Areas: flange at 10 mm from the top, web at 60 mm
  2. from the top
  3. , (the smaller one governs)

Answer: mm from the top, mm⁴, design mm³

Chapter 5

Deflection of beams

Which syllabus covers thisAU CE3491 Unit IVVTU not in syllabusSPPU 202041MU MEC302 Module 4KTU PCMET302 Module 3

How do you calculate how much a beam deflects?

The elastic curve obeys . Integrating twice (double integration or Macaulay's method), with the support conditions fixing the constants, gives slope and deflection everywhere. For standard cases the results are worth remembering: a cantilever with a tip load deflects .

Beam deflection under load: interactive loads as you scroll

Double integration, Macaulay, area-moment or conjugate beam: which method when?

Double integration suits a single load expression. Macaulay's method handles several point loads with one equation using bracket terms. The area-moment (Mohr's) theorems are quickest for a slope or deflection at one point. The conjugate beam turns the problem into finding shear and moment in an imaginary beam loaded by .

Why does span length matter so much for deflection?

Deflection grows with for point loads and for distributed loads. Double the span and a cantilever's tip deflection rises 8 times under the same point load, 16 times under a UDL. That is why long beams are usually governed by deflection limits such as rather than by stress.

What does Maxwell's reciprocal theorem say?

In any linear-elastic structure, the deflection at point A caused by a load at B equals the deflection at B caused by the same load at A. So you can swap the load and measuring points, which simplifies influence-line work and testing. For a cantilever, a tip load's deflection at mid-span equals a mid-span load's deflection at the tip: .

Predict, then check

A cantilever carries a tip load. You make it twice as long. How much more does the tip deflect?

Worked examples

Cantilever, tip load · ISMB 200 ( cm⁴ from steel tables), m, kN, GPa

Answer: mm at the tip

Simply supported beam, UDL · m, kN/m, mm⁴, GPa
  1. at mid-span

Answer: mm, well within mm

Chapter 6

Torsion of shafts and springs

Which syllabus covers thisAU CE3491 Unit IIIVTU BME301 Module 5SPPU 202041 Unit IVMU MEC302 Module 4KTU PCMET302 Module 2

How do you find the shear stress in a twisted shaft?

Under torque a circular shaft's shear stress grows linearly from zero at the centre to a maximum at the surface. The torsion equation links torque, stress and angle of twist, with for a solid shaft.

A shaft twisting under torque: interactive loads as you scroll

How much power can a shaft transmit, and why are hollow shafts better?

Power (watts, with in rpm and in N·m), so for the same power a faster shaft carries less torque. Because the core carries little stress, removing it saves weight for little loss of strength: a hollow shaft with keeps about 87% of a solid shaft's torque capacity at 64% of the weight.

How do you design a shaft that carries both bending and torque?

Most real shafts, such as a gear shaft between bearings, bend and twist together. Combine them into an equivalent torque for the maximum shear stress, or an equivalent moment for the maximum normal stress, then size the shaft for whichever governs. Shafts in series share torque; shafts in parallel share angle of twist.

How stiff is a helical spring?

A close-coiled helical spring's wire is mostly in torsion. Its stiffness is very sensitive to wire diameter and mean coil diameter . The maximum shear stress is multiplied by the Wahl factor to account for coil curvature and direct shear. Springs in series add flexibility (); in parallel they add stiffness (). Open-coiled springs add a bending term because the coil angle is large.

Close-coiled helical spring: interactive loads as you scroll
Predict, then check

Two springs are identical except that one has wire twice as thick. How much stiffer is it?

Worked examples

Stress and twist in a solid shaft · mm, m, N·m, GPa

Answer: MPa, twist

Size a shaft for a 30 kW motor · kW at rpm, allowable shear 40 MPa
  1. N·m
  2. , so choose a standard 30 mm shaft

Answer: mm, use 30 mm

Shaft under bending and torque · Solid shaft mm, kN·m, kN·m
  1. kN·m
  2. kN·m,

Answer: MPa, MPa

Helical spring · mm, mm, , GPa, N
  1. N/mm
  2. , ,

Answer: N/mm, mm, MPa

Chapter 7

Columns and buckling

Which syllabus covers thisAU not in syllabusVTU BME301 Module 5SPPU 202041 Unit IVMU MEC302 Module 6KTU PCMET302 Module 4

Why do long columns fail before the material is crushed?

A slender column in compression becomes unstable at the Euler critical load and bows sideways, often at a stress far below the material's strength. is the effective length, set by the end conditions: pinned-pinned, fixed-free, fixed-fixed and fixed-pinned.

Euler buckling of a column with different end conditions: interactive loads as you scroll

When does Euler's formula stop working, and what replaces it?

Euler's formula assumes a long, perfectly straight column and over-predicts strength for short, stocky ones (low slenderness ). Rankine's formula blends crushing and buckling: it gives the crushing load for short columns and approaches Euler's load for long ones.

Predict, then check

A column fixed at the bottom and free at the top is changed to fixed at both ends. How does its buckling load change?

Worked examples

Euler load for a steel strut · Solid round, mm, m, pinned at both ends, GPa
  1. kN
  2. mm, so (a long column)

Answer: kN

End conditions and Rankine · The same strut
  1. Fixed-free: m, kN
  2. Fixed-fixed: m, kN
  3. Rankine ( MPa): kN; , so kN

Answer: 16.8 kN fixed-free, 269 kN fixed-fixed; Rankine 60.8 kN pinned

Chapter 8

Thin and thick cylinders

Which syllabus covers thisAU CE3491 Unit VVTU BME301 Module 2SPPU not in syllabusMU MEC302 Module 5KTU not in syllabus

Why do pressurised pipes split along their length?

In a thin cylinder (), internal pressure causes a hoop (circumferential) stress and a longitudinal stress. The hoop stress is twice as large, so failure starts with a crack running along the length. A thin sphere carries in every direction, which is why spherical tanks can have thinner walls.

Stresses in a pressure vessel: interactive loads as you scroll

How much does a thin cylinder grow under pressure?

Each stress causes strain in its own direction and Poisson contraction in the other. The volumetric strain is twice the hoop strain plus the longitudinal strain. The change in diameter is hoop strain × , which is how much a pipe swells when it is pressurised.

How are stresses distributed in a thick cylinder?

When the wall is thick, stress is no longer uniform across it. Lamé's equations give the hoop stress highest at the inner surface and falling towards the outside, and a radial stress equal to at the inside and zero at the outside. That is why high-pressure cylinders are built up from shrink-fitted layers.

Predict, then check

A thin cylinder and a thin sphere have the same diameter, wall thickness and pressure. Which has the higher maximum stress?

Worked examples

Thin cylinder · m, mm, kPa

Answer: Hoop 20 MPa, longitudinal 10 MPa

Swelling of a pressurised cylinder · m, mm, kPa, GPa,
  1. , so
  2. ;

Answer: Diameter grows 0.17 mm; volume by 0.019%

Boiler shell thickness · m, MPa, allowable stress 100 MPa
  1. Hoop stress governs:
  2. Choose 12 mm plate (before corrosion allowance and joint efficiency)

Answer: mm, so 12 mm plate

Thick cylinder by Lamé · mm, mm, MPa
  1. Hoop at the inner surface
  2. Hoop at the outer surface
  3. Radial stress: MPa inside, 0 outside

Answer: Hoop 52 MPa inside, 32 MPa outside

Chapter 9

Strain energy and impact loading

Which syllabus covers thisAU not in syllabusVTU BME301 Module 1SPPU not in syllabusMU MEC302 Module 5KTU not in syllabus

What is strain energy?

Work done in deforming a body is stored as strain energy (the area under the load-extension line). The maximum energy a material can store without permanent set, per unit volume, is its modulus of resilience .

Why does a suddenly applied load cause double the stress?

A load lowered gently produces . Released suddenly from contact, it falls through the extension and stores twice the work, so . Dropped from a height , the stress grows further. Even small drops multiply the stress, which is why impact matters in design.

Gradual, sudden and impact loading of a bar: interactive loads as you scroll
Predict, then check

A 1 kN weight dropped from just 10 mm onto a steel bar ( mm², m). Compared with lowering it gently (2 MPa), the stress is about:

Worked examples

Gradual and sudden load · Steel bar mm², m, GPa, kN
  1. Gradual: ; J
  2. Sudden:

Answer: 100 MPa gradual, 200 MPa sudden

Impact load · kN dropped through mm onto a collar at the end of the same bar

Answer: MPa

Keep going

Recommended reading

  • Strength of Materials, R. K. Bansal
  • Strength of Materials, S. Ramamrutham and R. Narayan
  • Mechanics of Materials, S. S. Rattan
  • Mechanics of Materials, F. P. Beer, E. R. Johnston, J. T. DeWolf
  • Mechanics of Materials, J. M. Gere and B. J. Goodno
  • Engineering Mechanics of Solids, E. P. Popov

How this book was made

Chapters follow the official syllabi listed above. Every interactive's formulas and every worked-example number were checked by script. Explanations, animations and examples are original to Skill-Lync. Topics informed by MIT OpenCourseWare 2.001 (Mechanics & Materials I), CC BY-NC-SA. All explanations, animations and examples are original to Skill-Lync; MIT does not endorse this page.

From the exam to a core job

Talk to a counsellor.

Ask how CAE engineers use strength of materials on real projects, and what the PG Program in CAE (FEA) covers.

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.

Talk to a career counsellor

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.