Week 8 - Challenge 3 - Coin Holder Design

Title: Design and Development of Backdoor Design Objective Developing a back-door design based on the styling surface with given information and to position the latch reinforcement striker, hinge and wiper mountings. Introduction Backdoor is also known as tail gate. Backdoor is also has a swinging or closure commodity.…

Aim  To design & develop the Roof of a car with its components by following the master section and design parameters. Objective: To develop the essential flanges and reinforcements using roof styling as input. To do a curvature study on the roof and perform calculations to determine the position of the Bow-roof. To determine…

Aim: To design fender mountings by the given cad data and explain. Fenders are essential components of various vehicles, particularly automobiles and bicycles. They serve the critical purpose of protecting vehicles from road debris, mud, water, and other hazards, preventing damage to the vehicle body and ensuring the safety…

AIM To find section modulus of hood design that i designed. What is Section Modulus? Section modulus is a fundamental concept used in structural engineering and mechanics to quantify a cross-sectional shape's resistance to bending. When a load or force is applied perpendicular to the longitudinal axis of a structural member,…

AIM : To design the hood of a car with the given input Outer panel and its dimensions. What is the meaning of car hood?  A car hood, also referred to as a “bonnet” in some countries, is the hinged cover that rests over the engine bay of a front-engine vehicle. The car hood protects the engine and…

1. What is Under body Coating?    Underbody coatings are those which are used to prevent car bodies against rust & corrosion. This underbody coating helps in protection from dust and moisture also some other factors such as poor road conditions, rocks getting thrown from tires and denting the metal and salt…

Project Objective:- In This Project, I am Going to Suggest a Big Car for Mr.D.S. Pughazhyendhii Under 8 to 10 Lakhs on Road for Official and Family Purpose Traveling Distance Around 500km. Suggested cars are as follows: Maruti Ertiga Renault Triber Tata Nexon Tata Punch Maruti Fronx Kia Sonet Report I will be suggesting…

 AIM :- To create a CAD model for door trim panel's parts by considering the given inputs of class A surface along with master section by following the design rules followed in OEM and tier1 companies. OBJECTIVE: To create  Class B & Class C surface From the input Class A surface From the OEM. Closed solid body using nominal…

Aim To create CV joint Using Assembly cat part.       AIM: To create Quick Return Mechanism Part using Assembly Cat Part  

Aim:To Create a Pillar design with the help of the master section TOOLING AXIS: To create the tooling axis, I extracted a surface from class A and created a point in the middle of the surface by using the point command and created a line at that point through the x-axis. Now, I performed a draft analysis check from that…

AIM   Create the Door Trim Lower Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model.  Create the Heat Stakes and the locators…

AIM Create the Dog House for the Door Trim considering the design rules mentioned in the video. Consider the thickness of the part to be 2.5 mm. DOG HOUSE Dog house is an engineering feature used in plastic trim design. Dog houses are used as supporting feature. Sometimes other engineering features like snaps;…

AIM: To Create the Door Handle Component from the given Class-A surface. To Create the tooling axis for the given Class-A Surface meeting the requirements of the draft angle. To Attach B side Features in the component. To perform the Draft analysis on the model.  DESCRIPTION:   1. CREATING TOOLING AXIS -…

Aim: Create the Core and cavity blocks for the switch bezel designed in the earlier challenge. DESCRIPTION:   1. CREATING TOOLING AXIS -                       The Tooling Direction is basically the direction that the mold pulls a part. The mold is built…

AIM To Create the Door Trim Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model.  Take the Thickness of the component to be 2.5 mm…

Create the Bumper Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model.  Given class A Creating Tooling Axis After checking all directions…

Create the Coin Holder Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model.  GIVEN CLASS A First step is to create tooling axis for the…

AIM To Create the Switch Bezel Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model.  Class a surface Tooling Axis It is basiacally a axis…

Subject Create the Base Bracket Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model. Given Class A surface First we have to check the connectivity…