Week -2

Traffic Jam Assistant Feature  Objective: To develop one specific requirement of Traffic Jam Assistant algorithm which would predominantly feature in the IPC algorithm.Please note that the whole Traffic Jam Assistant is a very huge algorithm & only one small part of the logic is implemented here. Idea is to familiarize…

ADAPTIVE CRUISE CONTROL (ACC) OBJECTIVE: Developing Adaptive Cruise Control feature as per the Requirement Document using MATLAB Simulink. Follow all the MBD related processes: Requirement Tagging & Traceability, SLDD creation, Configuration Parameter changes, Model Advisor check & Code Generation. In Configuration…

VEHICLE DIRECTION DETECTION Objective: Development of MATLAB Simulink model as per given requirement. Tag the requirements to the simulink model; tagging requirement 1 & requirement 2 to their corresponding subsystems. MBD compliant changes, Data Dictionary creation & code generation is added advantage, and that…

For a 10 cell series lithium ion battery model, simulate the thermal effects and compare life cycle performance at various temperatures, charge & discharge rates using MATLAB. Objective: To create a MATLAB model for Lithium ion battery pack of 10 cells connected in series. To simulate the thermal effects and compare…

Battery pack capacity: 18 kWh Cell: ANR26650M1-B  Prepare a detailed battery pack drawing along with its enclosure. State your assumptions. Objective: For the cell model of ANR2665031-B, To calculate the all necessary parameters required to design a battery pack. To make a report of all calculated parameters.…

https://in.mathworks.com/matlabcentral/fileexchange/72865-design-and-test-lithium-ion-battery-management-algorithms 1.Simulate the 3 test cases from harness dashboard and write a detailed report on the results 2.What is coulomb counting? Refer to the above model and explain how BMS implements coulomb counting for SOC estimation…

1.Prepare a table which includes materials & chemical reactions occurring at the anode and cathode of LCO, LMO, NCA, NMC, LFP and LTO type of lithium ion cells.Give your detailed explanation on it? Solution: Lithium-ion (Li-ion) batteries are an important component of energy storage systems used in various applications…

Create a MATLAB model of electric car which uses a battery and a DC motor. Choose suitable blocks from Powertrain block set. Prepare a report about your model including following: Objectives:         1. System level configurations        2. Model parameters      …

Part A: 1. Search and list out the total weight of various types of aircrafts.  Solution: The aircraft gross weight is the total weight at any moment during the flight or ground operation. An aircraft gross weight decreases durig a flight due to fuel and oil consumption. It may varies during a flight due to payload…

1. For a defined driving cycle, calculate the energy required for braking. Solution: A driving cycle is a series of data points representing the speed of vehicle versus time. Driving cycles are produced by different countries and organisations to assess the performance of vehicles in various ways, as for instance…

1. A. Explain a MATLAB demo model named ‘Speed control of a DC motor using BJT H-bridge’.     B. Comment on the armature current shoot-up from the scope results.     C. Refer to the help section of ‘The Four-Quadrant Chopper DC Drive (DC7) block’. Compare it with the H-bridge…

1. Which types of power converter circuits are employed in electric and hybrid electric vehicle? Solution: The demand of electrical power in vehicular application is growing rapidly as the mechanical components are being replaced by the elctrical and electronic components. it is expected that the power demand. In…

1. What is the difference between mapped and dynamic model of engine, motor and generator? How can you change model type?  Solution: Powertrain blockset consists two types of combution engine models. They are Mapped and Dynamic model. Mapped Model Engine: These are used to represent macro engine behaviour and measures…

1.   For EV_defaults_in file, if cargo mass is 500 kg with all other default conditions, can the vehicle travel for 45 km with FTP drive cycle? Conclude your observations. Solution:  ADVISOR Tool: ADVISOR, NREL's ADvanced VehIcle SimulatOR, is a set of model, data, and script text files for use with MATLAB…

Aim: To study, analyze and prepare a technical report explaining the model properties of Baja ATV model. First we are going to know What is ATVs:                An All-Terrain Vechile(ATV) is defined as a motorized off highway vechile designed to travel on four low pressure or non-pneumatic…

1. To implement control logic of a washing machine using stateflow as per given sequence, Objective: If the power supply is available, the system gets activated if the water supply is not available, stop the process and indicate it through LED Soaking time should be 200sec folowed by washing time of 100sec then rinsing…

Answers are attached through files.