Radar Mast & Final Assembly of Yacht

Objective:- To design a Roof with Roof rails Introduction:- An automobile roof or car top is the portion of an automobile that sits above the passenger compartment, protecting the vehicle occupants from sun, wind, rain, and other external elements. Because the earliest automobiles were designed in an era of horse-drawn…

AIM :- To Design Front Fender. INTRODUCTION :- A fender is the part of a car that protects and frames its wheels and keeps mud from splashing it. Most modern vehicles have fenders on their front wheels. When you get into a minor car accident, you can call it a "fender bender," and it's possible that your fenders…

Objective:- To design the given harness according to the diagram. Given diagram:-  HARNESS A:-   CONNECTIVITY CHECK   HARNESS B:-    CONNECTIVITY CHECK CONVERTED AS A PART BODY AND SAVED AS IGS FORMAT:-   CONCLUSION :- The Harness assembly from the given data  has been successfully…

AIM:- Route the following harness layout in Electrical workbench. Make assumption for harness bundle diameters. Use Following connectors as shown in layout diagram. Add protective covering on all branches connected to DT06-2S & DT06-4S connectors. Keep end extremity at 30mm (from connectors end)   Connector…

ANSWER 1:- Create a points and planes in part design workbench Define the part as support in electrical part design workbench select the entry point and exit point and base plane Repeat for the other side as it is.   ANSWER 2:- In part design create a point and axis system for backshell entry create a bundle connection…

AIM :- To calculate the section modulus of the hood for analyzing it’s strength. INTRODUCTION:- Section modulus is a geometric property for a given cross-section used in the design of beams or flexural members. Other geometric properties used in design include area for tension and shear, radius of gyration for…

AIM :- To Design and assemble the car hood. INTRODUCTION :- The hood or bonnet is the hinged cover over the engine of motor vehicles. Hoods can open to allow access to the engine compartment, or trunk on rear-engine and some mid-engine vehicles) for maintenance and repair.    MASTER SKETCH :- MATERIAL…

INTRODUCTION : - Cars today are equipped with electronic components that, in addition to the basic operations of moving, turning, and stopping, perform various other functions as well. Wiring harnesses are indispensable in controlling these electronic components, transmitting power and signals to every part of the…

UNDERBODY COATING   Underbody Coating is a sprayable coating, which protects the under surface of the vehicle from corrosion. Underbody coating provides long term protection from corrosion to car's underbody. It also protects parts like internal body panels, frame rails and other inner cavities that are…

  BENCHMARKING Benchmarking is a process of measuring the performance of a company’s products, services, or processes against those of another business considered to be the best in the industry, “best in class.” The point of benchmarking is to identify internal opportunities for improvement. By studying…

Title of the Project : Advanced Sheet Metal Design Using NX Cad Challenge_7_ Metal bracket-II. Objective : To design a Sheet Metal Design Using NX Cad sheet metal application. Introduction :  Unigraphics NX (also known as Siemens nx) is an advanced High-end CAD/CAM/CAE software package…

  Tittle of the Project:- Advanced Sheet Metal Design Using NX CAD Challenge_6_Bracket.   Objective:- To design a Bracket by using Siemens NX12 Sheet metal application.   Introduction:-   Unigraphics NX (also known as Siemens nx) is an advanced High-end CAD/CAM/CAE software package…

Title:- creation of box Assembly using NX cad. objective:-To design a box assembly and create a draft of it using Siemens NX Sheet metal application. INTRODUCTION:- Sheet metal is metal formed by an industrial process into thin, flat pieces. Sheet metal is one of the fundamental forms used in metal working, and…

Tittle : Odd Shaped Enclosure design by using NX Cad Challenge. Objective:   To design and modelled odd shape enclosures using siemens NX-CAD.  To draw the drawing for the designed model using drawing application in NX. Introduction :  Unigraphics NX (also known as Siemens nx) is…

Objective: To design an advanced casing using the sheet metal application in siemens NX. Introduction:  sheet metal design is a vast domain in the design of any sheet metal industry,it is used many sectors including the aeronautics & automotive sectors , in this sheet metal casing design we will look at the design…

AIM: Development of a Door Trim panel. OBJECTIVE: To make a Door trim panel in Catia V5 using the given Class A surface.   ABSTRACT: This project contains the brief theory on how the approach has been made inorder to obtain the solid door trim panel. It also show case certain rules regarding the maufacturing…

AIM: CREATION OF DOOR ARM REST AND ADD THICKNESS OF 2.5 mm In an automotive context, an armrest (or arm rest) is a feature found in many modern vehicles on which occupants can rest their arms.  Tooling Axis: It is the direction in which the component will be ejecting after…

AIM : To create assemblies according to the provided with 2D diagrams of the components by first creating the individual part files and then create a complete assembly of those part files in the assembly  THEORY : Assembly modeling is the process of creating designs that consist of two or more components assembled…

AIM- To create a B pillar of a car using the master section and Class A surface as an input and performing Draft analysis on the final model. Objective- To ensure proper tree structure is followed. Creating a tooling axis and following design rules. Creating Class B and C surface using Class A surface as an input. Following…

OBJECTIVES:  To create a door applique design from the given class A surface and to create engineering Features to fit the component in the main surface.   INTRODUCTION:   HEAT STAKING - Heat Staking is a pulsed-heat process to join two or more parts out of which one at least is made of plastic. The process…

AIM- Create the screw boss and dog house for the centre console coin holder considering the design rules. INTRODUCTION ATTACHMENT FEATURES: 1. SCREW BOSS :- Boss features are commonly found in injection molding designs. They are used to aid in the assembly of molded parts by providing a channel for a screw.  …

Aim : To create the rib for the Centre console coin holder considering the design rules. Introduction: Plastic parts design is a very complex process and it requires the involvement of many factors like functional requirements, process constraints, material selection and assembly or structural issues. Wall thickness, Draft,…

OBJECTIBVE:  To Create the Core and cavity blocks for the switch bezel. CORE: The core is the part which forms the internal shape of molding.it is respponsible for half of the molded part. actually core is the projection of the body CAVITY: The cavity is the part which forms external…

OBJECTIVE - Create the Coin Holder Plastic component through the given Class-A surface. PROCEDURE-   check is there any open boundaries present or not which may create errors while designing by using boundary option.   The tooling axis is the direction of drawing a sheet metal where the finished component…

OBJECTIVE To create the Switch Bezel plastic component through the given Class-A surface and at the end performing the draft analysis on the closed surface model.    PROCEDURE  Check the connectivity of imported of Switch Bezel model in CATIA V5 Class A Surface using boundary option. Ensure that there is…

OBJECTIVE: Creating the Base Bracket Plastic component through the given Class-A surface. Class A surface: It is the visible aesthetic surface which have curvature and tangency alignment to ideal aesthetical reflection quality of any automotive component. Class A surface refers to those surfaces which are visible It is…

DRAFT ANALYSIS REPORT: Draft: Draft is an angular tapering given at the design stage to every Plastic Component that has to be manufactured. It is given in the direction of the Mold Movement. The Draft allows the parts to release easily from the mold without creating friction between the surface of component and the core…

                                                                     Project Report                  …

                                                                            Project Report            …