…

AIM: To sketch a plan of G+1 floor residential building according to Vaastu Shastra and listing down the names of the structural drawings required to be provided to the construction site. INTRODUCTION TO VAASTU SHASTRA:- Vaastu Shastra:- Vastu Shastra is the Ancient Indian Science of architecture and acts as a guideline…

Project 1 (AutoCAD) Submitted by Abdul Waheed Pedhar Commands Used in this challenge Line Xline Polyline Rectangle Circle Arc Trim Move Offset Hatch Layer MatchProp Multileader Fillet Copy Explode Dimlinear Dimcontinue Dim break Dim update Hide pallets (POFF) Show pallets (PON) Q. Design and Draft a layout of a residential…

Aim: To create: Template, inserting text and attributes Doors of warehouse and placing it in blocks Electrical legend and making it blocks Different types of door for residential project Drawing bars, making it as block and making it as a table as bar bending schedule.   Commands used:  Block. Insert. Attributes.…

Creating Kitchen layout, Hatching of Architectural elements and sectional view of an Industrial Building in AutoCad   1} AIM : Create the layouts of the Kitchen and provide hatches pattern as shown. Also, use blocks wherever required. Provide appropriate dimensions in the plan. Assume the size of doors,   …

Creation of Multiple viewports, Scaling the drawing, and setting in Template in AutoCad   1. Create a layout of the Plan and Section A of the project in Challenges 7, using the template Tutorial-mArch.dwt in a scale as given in the Figure. Use the MV command to create the viewport of the size as shown in Figure. Also,…

AIM: To create 3D model and view of: Furniture element Isolated footing AASTHO type girder Drop column with panel A wall Commands used: Extrude. Offset. UCS. Box. Union. Subtract. Move. 3d orbit. Loft. Sweep. Cone. Region. Boundary. PROCEDURE:  Open the AutoCAD, click on workspace switching and change it to 3d…

Challenge 12 Commands Used in this challenge Line Rectangle Trim Move Copy Explode Circle Dimlinear Dimcontinue Boundary 3Dorbit 3D rotate Extrude Region UCS Camera Block Render RR Sweep Create Light   Create a 3D Isometric View of the building with plan and elevation given.     Aim: To draw the 3D Isometric View of the…

Project 2 AIM:  To create a 3D rendered model for a Residential Building in AutoCAD INTRODUCTION: The main objective of this project is to understand about to create a Plan in 2D, then convert it into 3D using AutoCAD 3D, applying materials and rendering. AutoCAD is primarily used for generating 2D sketches. While it is…

1) Aim - To create a Ceiling from the Architecture tab to the first floor level .  Introduction Revit is an Building Information Modeling software and is product of an Autodesk. It can be useful for Architects , Civil engineer , Structural Engineer , Mechanical Engineer , Electrical and Plumbing Engineers.…

1. Select the type of Structure you want -    i)  As there are 3 options - a) Multi-Unit Residential Apartment                                         b) Office Buildings          …

1. Aim - To create a sinusoidal points and create a curve and create a surface out of the curve by using Dynamo  Introduction -  Dynamo is a visual programming software which is used to enhance the project process. Its a software that allows you to type lines of code; while also creating an algorithm that consist of nodes…

Aim - To use the architecture/structural project file developed from week 6-8, Export the Revit file to Navisworks cache file. Introduction -  Navisworks is a software tool which is generally used by Management files people. It helps us to coordinate or manage the project with more efficiency. It allows…

Identification of Cracks   1) What is the mode of failure or damage of the beams in the figure above? Would you characterize the case as damage or as a failure? Are the damages repairable? Elaborate. a)              This crack will be formed due to the flexural failure of a…

1. Differentiate Static analysis and Dynamic analysis with proper representing pictures STATIC ANALYSIS Static analysis can only be performed if the system being simulated does not depend on time, and if the loads being applied are constant. Static analysis don't consider inertia. Static refers to the force that has constant…

Aim -  1) To calculate Ln, Mnand Γn for each of the five modes. 2) To calculate the effective modal mass Mn* and the modal mass participating ratio for the 5 modes. 3) To find the base shear for each of the 5 modes of vibration and the combined base shear as per SRSS rule. 1   4)  How…

Q.1)    1)    1) Symmertry - i) The given framing layout of plan is Symmetrical in nature by seeing the aspect ratio of the framing plan. ii) Because of the symmetrical nature the distribution of load is uniform through out the frame. iii) Which helps in Resisting the Lateral forces which are acting…

Q.1)       Properties                           Case a                 Case b                          Case c    …

Aim - To model a 25 storey building on ETABS with structural properties. Introduction -  1) ETABS is an engineering software product that caters to multi-story building analysis and design. 2) Modeling tools and templates, code-based load prescriptions, analysis methods and solution techniques, all…

Aim  -  To do Comparative Analysis of different storey buildings for Seismic forces Introduction -  ETABS is an engineering software product that caters to multi-story building analysis and design. Modeling tools and templates, code-based load prescriptions, analysis methods and solution techniques, all…

Aim - i) To design the beams in detail from the Etabs 2018.                 ii) To provide the detailing of longitudinal and shear reinforcement for two continuous                        beams.      …

Aim - To provide the details of longitudinal reinforcement for the two columns (3A & 3B), from foundation to terrace level   Introduction -  A column in architecture and structural engineering is a structural element that transmits, through compression, the weight of the structure above to…

Aim -  1) To run the Analysis and Design the RCC Shear Wall           2) To extract values of Longitudinal Steel Ratio, Boundary Element Length and Shear                           Reinforcement ratio from Design results.…

Aim - i) To design a structural model on the basis of provisions from IS 1893 and IS 13920 in                     seismic zone 5.          ii) To Run a modal response spectrum analysis and check analysis results of the Etabs . Procedure - …

Aim - To design a square footing for a column size of 400x400 . Introduction -  The footing is a structural member that safely transmits the load of the upper building to the ground, and is the first construction member of the building. The basic method of footing design is to distribute the load so…

Aim - i) To  model the isolated footing provided in week 11 challenge on SAFE.          ii) To Analyze and design it to verify the size, depth and steel provided as per calculations.          iii) To model the pile cap on SAFE software. Procedure -    Step…

Aim - To carryout modelling, analysis, design, and preparation of construction drawings of a G+3 RCC building situated in Guwahati Assam. Procedure -    Step 1)  i) Open the Etabs software from deskstop icon  ii) Once software is open - Click on New model      Step 2)  i) Once…