MODELING OF AMERICAN CHOPPER USING SOLIDWORKS   OBJECTIVE The main objective of this project is to model a various components of the American Chopper using solidworks softwere. Assemble the…

Radar Mast.     Radarmust feature tree.   2.Yacht assembly.     Yacht assembly feature tree.

AIM: To create a base bracket plastic component designed based on the given class A surface.A Surface should be created meeting the requirements of the draft angle and Draft analysis on the model. REPORT ON DRAFT ANALYSIS: given class A surface:              Creating a Tooling axis:…

AIM:        To Create the Switch Bezel Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model. Surface creation:    …

AIM:         To Create the Coin Holder Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model.  Surface creation:  …

AIM:          To create the Bumper Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model.  INTRODUCTION CLASS A…

AIM:         To create the Core and cavity blocks for the switch bezel designed in the earlier challenge.  INTRODUCTION:                           The plastic parts were usually manufactured with the forming process, particularly…

AIM:           To design ribs & screw boss on the Drill handle considering every RIB & Screw Boss design rule following in industry. Introduction: Class-B surface contains all the engineer data required for the model to be completed.  Some of the major features of the B-side are:…

 AIM:           TO Create the Door Trim Lower Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model.  Create…

AIM:          To create A PILLAR design model using master section then create a draft analysis using catia V5 softwere. CREATE A PILLAR USING MASTER SECTION:  OBJECTIVES:          To create the class B and class C surfaces from the given class A surface To form a…

AIM:          To Create the Dog House for the Door Trim considering the design rules and also going to do draft analysis. "C" is where the doghouse contacts the backside of the surface                               …

AIM:         To create assemblies of Quick return mechanism and CV joint and to also create 2D drawing of the given assemblies using CATIA v5 softwere. INTRODUCTION: ASSEMBLY:                    Assembly modeling is a technology and method used…

AIM:         To prepare a detailed report on benchmarking and explaining what is Bench-marking , Compare at least 4 Vehicles and Provide a Preoper conclusion for the report ,suggesting a suitable vehicle among the comparison made. BENCHMARKING:                …

AIM:                      A report on Underbody Coating and its purposes. Introduction:                     Modern-day cars are made of various materials combined but the main chassis of the car body is made…

AIM :            To Design the hood of the car using Hood Outer Panel, Inner Panel and the necessary reinforcements by following the Master Section mentioned with the Design parameters. INTRODUCTION:             Hood is main component of a car at the…

Aim:          The main objective of this project is to understand and learn the basic tools and advanced tools used in NX and calculation as well as section modulus and optimization of Car Hood and calculate the Section Modulus and optimization using the formula. SECTION MODULUS:  …

                                                       DESIGN FENDER - WHEEL ARCH AIM:          The wheel arch challenge is to calculate the wheel arch area…

                                                     Automotive Fender Design (BiW)AIM:                To craete a front fender Follow the given…

                                    AUTOMOTIVE SHEETMETAL ROOF DESIGN USING NX CAD   AIM:               In this project, I am going to the Design of Roof and Develop the Essential Flanges…

                                                             Car BackDoor Design Aim:           To design car back door from given styling…