Objective:           To create the 1D element for given component with given cross section and DOF           Rod element - Translational DOF should be constrained with RBE2 link ( at A )           Beam element - All elements should be constrained…

Aim :     For the given Hood model, Take the mid surface for all the components after checking the geometrical errors and mesh the mid surface with the given element Quality criteria.   Introduction :             The Hood or Bonnet is the hinged cover over the engine…

Aim :   Practice all the Morphing techniques that were shown in the video for Model-1.   Perform morphing for the Model-2 and Increase the Height of the Dog houses and Ribs.    Introduction :  The Morphing feature is basically as its name says , an algorithm that lets the user rapidly…

Aim :  For the given Rear view mirror component, check for the geometrical errors and mesh the Surfaces with the given 2D element Quality criteria.  Objective :  To understand the  Tetra Meshing on the components To define volume for the component To Mesh the volume using volume mode To Mesh the model…

Aim :  To extract the mid surface and mesh the given bottle cap component using given quality critria and assign correct thickness to the property Quality Critria : S.No  Quality Criteria  Value  1 Target/Average length   1 2 Minimum Length  0.5 3 Maximum Length  3 4 Aspect …

Aim :  The given Rear door FE model, Perform suitable connections between various parts . Create and Apply different PIDs for different components.    Procedure :    First we need to import the model as shown. Then the entire model will be separated into different PIDs This process can done by using Set PID > Select Macro…

  Time taken for Model 1 :  8 hrs   Time taken for Model 2 : 1:30 hrs   In model 1 having more off elements and some area more complex to clear the off elements . More  time consuming only for clearing off elements     

Dear sir,   Total time for solid  meshing : 4 hrs    Reson for Delay : due to some my acadamic work not able to submit on time . Thanks in advance

AIM :   For the given component, check for the geometrical errors and mesh with the given element Quality criteria. After meshing the component the thickness has to be assigned.     S.No Quality Criteria Value 1 Target/Average length   4 2 Minimum Length  2 3 Maximum Length  6 4…

AIM :      Importing Rear car suspension geometry into ANSA     Cleanup the Geometry until no  topological error is found     Generate mid surface for required parts     Generate volume mesh for hollow parts     Improve the mesh flow and solve  off elements…

AIM :   The objective of this challenge is to create a consisten system of units for the given input.. LS DYNA     doesn't have a default system of units.  User need to input material properties and physical dimension according to a consistent system of units as per their units as per their…

INTRODUCTION :  The Hood or Bonnet is hinged cover over the engine of motor vehicles. Hoods can open to allow access to the engine over the engine of motor compartment or trunk for  maintenance repair. In recent years the work has been done on the bumper and hood design of the vehicle front end to reduce the…

AIM :       To perform 3D Tetra Mesh on the given model.PROCEDURE : Model 1 : Import the given model and check any geometry error.In this model there are few missing surface . Fill the surface by QUICK EDIT > FILLER SURFACE OPTION.Next step is to defeature some edges which might for minimum length quality criteriaInitially…

AIM :  To Mesh the given geometry and create 1D connectors at desired locations using Hypermesh. The following connection have to be realized in each respective component. 1. Right_Rail_2 & Front_truss_1:- Seam-Quad(angled+capped+L) 2. Left_Rail_2 & Front_truss_1:- Quad elements 3. Front_truss_2,…

AIM : To extract mid-surface, geometry clean up and create the shell (two dimensional) mesh for the given side door inner panel according to the given quality criteria by using HYPERMESH.   QUALITY CRITERIA REQUIREMENT: PROCEDURE: First, import the side door inner panel model into HyperWorks. Since there are many…

OBJECTIVE: To mesh the given floor panel geometry through after generating its midsurface. To also ensure that mesh is of the highest quality (following given quality criteria) with a low number of trias and good mesh flow. Target Element Length = 5 Units S.N Quality Criteria  Value  1 Aspect Ratio  5 2 Skewness 45 3 Warping…