Dear sir, Total time for solid meshing : 4 hrs Reson for Delay : due to some my acadamic work not able to submit on time . Thanks in advance
Vignesh G
updated on 13 Apr 2022
Project Details
Leave a comment
Thanks for choosing to leave a comment. Please keep in mind that all the comments are moderated as per our comment policy, and your email will not be published for privacy reasons. Please leave a personal & meaningful conversation.
Other comments...
Read more Projects by Vignesh G (16)
Week 12:Project 2-Meshing of Rear Wheel Holder challenge
OBJECTIVE: To mesh the given floor panel geometry through after generating its midsurface. To also ensure that mesh is of the highest quality (following given quality criteria) with a low number of trias and good mesh flow. Target Element Length = 5 Units S.N Quality Criteria Value 1 Aspect Ratio 5 2 Skewness 45 3 Warping…
09 Jan 2023 04:54 PM IST
Week 12:Project-1-Meshing of Door Inner Panel Challenge
AIM : To extract mid-surface, geometry clean up and create the shell (two dimensional) mesh for the given side door inner panel according to the given quality criteria by using HYPERMESH. QUALITY CRITERIA REQUIREMENT: PROCEDURE: First, import the side door inner panel model into HyperWorks. Since there are many…
23 Dec 2022 12:04 PM IST
Week 9-Creation of 1D Connectors Challenge
AIM : To Mesh the given geometry and create 1D connectors at desired locations using Hypermesh. The following connection have to be realized in each respective component. 1. Right_Rail_2 & Front_truss_1:- Seam-Quad(angled+capped+L) 2. Left_Rail_2 & Front_truss_1:- Quad elements 3. Front_truss_2,…
19 Jul 2022 11:22 AM IST
Week 8-3D Tetra Meshing Challenge
AIM : To perform 3D Tetra Mesh on the given model.PROCEDURE : Model 1 : Import the given model and check any geometry error.In this model there are few missing surface . Fill the surface by QUICK EDIT > FILLER SURFACE OPTION.Next step is to defeature some edges which might for minimum length quality criteriaInitially…
16 Jul 2022 06:58 AM IST
Week 6-Meshing of Hood Challenge
INTRODUCTION : The Hood or Bonnet is hinged cover over the engine of motor vehicles. Hoods can open to allow access to the engine over the engine of motor compartment or trunk for maintenance repair. In recent years the work has been done on the bumper and hood design of the vehicle front end to reduce the…
31 May 2022 06:46 AM IST
Week - 1 - Consistency of Units
AIM : The objective of this challenge is to create a consisten system of units for the given input.. LS DYNA doesn't have a default system of units. User need to input material properties and physical dimension according to a consistent system of units as per their units as per their…
19 May 2022 02:13 PM IST
Project - 2 - Meshing on the suspension Assembly
AIM : Importing Rear car suspension geometry into ANSA Cleanup the Geometry until no topological error is found Generate mid surface for required parts Generate volume mesh for hollow parts Improve the mesh flow and solve off elements…
13 May 2022 11:02 AM IST
Project 1 - 2D meshing on the instrumental Panel
AIM : For the given component, check for the geometrical errors and mesh with the given element Quality criteria. After meshing the component the thickness has to be assigned. S.No Quality Criteria Value 1 Target/Average length 4 2 Minimum Length 2 3 Maximum Length 6 4…
27 Apr 2022 08:18 AM IST
Tool Test-2
Dear sir, Total time for solid meshing : 4 hrs Reson for Delay : due to some my acadamic work not able to submit on time . Thanks in advance
13 Apr 2022 05:24 PM IST
Tool Test 1
Time taken for Model 1 : 8 hrs Time taken for Model 2 : 1:30 hrs In model 1 having more off elements and some area more complex to clear the off elements . More time consuming only for clearing off elements
04 Apr 2022 02:18 PM IST
Week 6 - Creating connection for Rear door
Aim : The given Rear door FE model, Perform suitable connections between various parts . Create and Apply different PIDs for different components. Procedure : First we need to import the model as shown. Then the entire model will be separated into different PIDs This process can done by using Set PID > Select Macro…
02 Apr 2022 03:57 PM IST
Week - 4 - 2D meshing for Plastic components
Aim : To extract the mid surface and mesh the given bottle cap component using given quality critria and assign correct thickness to the property Quality Critria : S.No Quality Criteria Value 1 Target/Average length 1 2 Minimum Length 0.5 3 Maximum Length 3 4 Aspect …
24 Mar 2022 09:35 AM IST
Week- 5 - Solid meshing
Aim : For the given Rear view mirror component, check for the geometrical errors and mesh the Surfaces with the given 2D element Quality criteria. Objective : To understand the Tetra Meshing on the components To define volume for the component To Mesh the volume using volume mode To Mesh the model…
18 Mar 2022 07:54 AM IST
Week - 8 - Morphing
Aim : Practice all the Morphing techniques that were shown in the video for Model-1. Perform morphing for the Model-2 and Increase the Height of the Dog houses and Ribs. Introduction : The Morphing feature is basically as its name says , an algorithm that lets the user rapidly…
16 Mar 2022 04:25 PM IST
Week 3 - 2D meshing for sheet metal
Aim : For the given Hood model, Take the mid surface for all the components after checking the geometrical errors and mesh the mid surface with the given element Quality criteria. Introduction : The Hood or Bonnet is the hinged cover over the engine…
08 Mar 2022 06:22 PM IST
Week 4-1D Element Creation Challenge
Objective: To create the 1D element for given component with given cross section and DOF Rod element - Translational DOF should be constrained with RBE2 link ( at A ) Beam element - All elements should be constrained…
02 Feb 2022 05:45 AM IST