Q NO.1:- AIM:- To model a Ceiling from the architecture tab above the walls at the first-floor level. Introduction:- The creation of Ceilings within Revit is a very similar process that of floors and Roofs i.e. you can let Revit do most ofthe work and "guess" where you want the boundariew to be, or you can enter "Sketch…

Q No.1 Ans:- From the given options of type of structure for designing I have selected the Office Building.Q No.2 Ans:- The geographical and location details for my project modelling, based on assumptions of multi-unit residential apartment.Selected identify the modelling requirements from NBC.As above mentioned…

Introduction:-Dynamo is an open source visual programming language for Revit, written by designers and construction professionals. It is a programming language that allows you to type lines of code; while also creating an algorithm that consist of nodes.Using dynamo work can be carried  out with enhanced BIM capabilities…

Q No.1Ans:-AIM:-To use the architectural/structure project file developed from week 6-8, Export the Revit file to Navisworks cache file.Procedure:-Open the Revit software.Go to File -> Open -> Project.Select the "Architectural" file from the "Open" tab.Repeat the above process for adding Structural file.Now…

Cracks may occur in different components of a building due to External applied force in a different component of the building is greater than that of its resisting capacity.Poor quality of material used construction is not carried out by relevant drawing, prescribed job specifications, or work - man - like manner…

Q No.1:-Ans:-Static Analysis:-In static analysis we analysis static load means a force that has constant size, position and direction on or within a structure.Study of static load help determine the maximum allowable load to be applied to the structure.In static analysis we use equation of equilibrium for a structure under…

AIM:- To compute the values of seismic parameters based on the given structural data.Step -1:-Step -2:-Step -3:-Step - 4:-Step - 5:-Result:-Ln, Mn, Tn values are calculated for each ofthe 5 modes.The base shear force for each of the 5 modes is obtained.Effective modal mass and the modal mass participating ratio for…

Q No.1-Ans:-1.Symmetry:-Having a look over the aspects of symmetry of the framing plan, it is observed that the distribution of mass, Stiffness is across the plan; it is observed that the distribution of mass, stiffness is across the plan, it is considered for one of the good Symmetrical aspects. This tends to reduce the…

Q No.1Ans:- Structure(A)For this structure is considered as it is asymmetric in nature.Here cannot to be considered as a horizontal irregularities and the shear wall shape like L.There is some uncertainty concerning certain features of the seismic response of non-rectangular walls.It occurs lack of tensile capacity…

Given Data:-Structural Element SizesBeams: 300 x 400 mmColumns: 800 x 800 mmSlab: 150mm thickMaterial Properties:Grade of Concrete: M30Grade of steel Reinforcement bars: Fe415Loading Details:-Dead Load on beams from infill wall: 10kN/m (Let us assume the same for floor in view of parapet).Live load on floor: 3kN/m^2 (Let…

Aim:-To model and analyze multiple buildings with different floor levels and design parameters using ETABS software and compare the results to understand their overall seismic behavior.Introduction:-The structural configuration of the building pays a major role in determining the overall response during an earthquake.…

AIM: -To design the beams in detail from the ETABS 2018.To provide details of longitudinal and shear reinforcement for the give two continuous beams.To calculate the value of maximum shear force in any one of the spans in the continuous beams.INTRODUCTION: -Beams are horizontal structural elements used for supporting lateral…

AIM: - To providing details of longitudinal reinforcement for the two columns from foundation to terrace level.Steps to be followed: -Open the ETABS software.Use the model provided in the previous challenge.Next go to "Concrete Frame Design" icon in the icon's toolbar and select "view/revise preferences" from…

AIM: -The aim for this challenge is to run the analysis and to design the RCC shear walls. And to extract the values of longitudinal steel ratio, boundary element length and the shear reinforcement ratio from the design results.Procedure: -Open the ETABS software and open the attached file given in the question.Set the…