Report for the 2-D arm manipulator challenge clear all= remove items from workspace free the system memory close all= close running…

Modelling, Assembly and Photo Realistic Rendering of An American Chopper Motorcycle   Objective:- The main objective of this project is to create various 3D parts of an American Chopper Motorcycle in a 3D CAD software(SOLIDWORKS), assigning them the proper appearance, colour, decals. Finally creating assembly of the…

         Detailed report on the design and modelling of the Sunseeker Predator 108 luxury Yatch and Final Assembly of Yacht Report Created By- Rishabh Soni   Introduction:- Sunseeker Predator 108:-Sunseeker Predator 108 is a 32.92 m / 108′1″ luxury motor yacht. She was built by…

  BENCHMARKING   What is Benchmarking?   Benchmarking is a process where you measure your company’s success against other similar companies to discover if there is a gap in performance that can be closed by improving your performance. Studying other companies can highlight what it takes to enhance…

Underbody Coating and its Uses   In Indian road conditions, a cars underbody is most prone to corrosion. Underbody coating provides long term protection from corrosion to car’s underbody. It also protects parts like internal body panels, frame rails and other inner cavities that are not physically accessible…

Automotive Hood Design Using NX CAD   What Is Hood Of The Car?   A car hood also referred to as a bonnet in some other countries is the hinged cover that rests over the engine of a front-engine vehicle. Its purpose is to provide access to the engine for repair and maintenance. Car hoods are typically constructed…

Wheel Arch:-   Wheel Arch is the semicircular part of the fender which is located just above the wheel.   Wheel arch has its significant role in the designing of the car. The Arch is designed in order to safe the car BIW and the pedestrian from the mud, road particles, road side dirt and the pebbles to hit the…

Fender Design Challenge   Fender is the American English term for the part of an auto-mobile, motorcycle or other vehicle body that frames a wheel well (the fender underside). Its primary purpose is to prevent sand, mud, rocks, liquids, and other road spray from being thrown into the air by the rotating tire. Fenders…

Objective To explain briefly about section modulus and determine the section modulus of the designed hood section which was drafted in the previous challenges, and to optimize the section modulus of the section by making necessary changes in the section for better strength and rigidity.   Section Modulus Section Modulus…

Roof Challenge   Objective:- 1. For the Given Roof styling, create an ASSEMBLY by developing the essential flanges for the outer roof and creating the reinforcements. 2. To make the necessary flanges and ditch area around the upper roof panel. 3. To do the Heat Distortion calculations and Snow load factor calculations…

Design of Backdoor     Objective:- 1.To Use the provided styling surface to come up with a back door design, use appropriate design methodologies, and provide the necessary reinforcements and embosses. 2.To Develop a detailed report for the Back door design by explaining the design methodologies and about the…

Base Bracket Design       Objective- To Create the Base Bracket Plastic component through the given Class-A surface by creating tooling direction, the tooling axis for the given Class-A Surface should meet the requirements of the draft angle and at the end to perform the Draft analysis on the model.  …

Switch Bezel Design       Objective- To Create the Switch Bezel Plastic component through the given Class-A surface by creating tooling direction, the tooling axis for the given Class-A Surface should meet the requirements of the draft angle i.e. minimum 3°and at the end to perform the Draft analysis…

Coin Holder Design   Objective- To Create the Coin Holder component through the given Class-A surface by creating tooling direction, the tooling axis for the given Class-A Surface should meet the requirements of the draft angle i.e. minimum 3°and at the end to perform the Draft analysis on the model.  …

Bumper Design   Objective- To Create the front bumper Plastic component through the given Class-A surface by creating tooling direction, the tooling axis for the given Class-A Surface should meet the requirements of the draft angle i.e. minimum 3°and at the end to perform the Draft analysis on the model. Draft…

Switch Bezel Design       Objective- To Create the Switch Bezel Plastic component through the given Class-A surface by creating tooling direction, the tooling axis for the given Class-A Surface should meet the requirements of the draft angle i.e. minimum 3°and at the end to perform the Draft analysis…

Attachment Feature Creation (Ribs & Screw Boss) on A Door Handle     Objective- To Create the Attachment Features (Ribs & Screw Boss) on A Door Handle through the given Class-A surface by creating tooling direction, the tooling axis for the given Class-A Surface should meet the requirements of the draft…

Dog House for the Door Trim   Objective- To Create the Dog House on A Door lower trim through the given Class-A surface by creating tooling direction, the tooling axis for the given Class-A Surface should meet the requirements of the draft angle i.e. minimum 3°and at the end to perform the Draft analysis on the…

Advanced Sheet Metal Design Using NX Cad Challenge_1_Casing Design   Objective- To design a sheet-metal casing component with the use of NX-CAD Software and Write a detailed report on Sheet Metal Component with good explanation on Sheet Metal modelling tools applied throughout the modelling. Also attach the Final…

Advanced Sheet Metal Design Using NX Cad Challenge_2_Box Assembly   Objective- To design a sheet-metal Box Assembly with the use of NX-CAD Software and Write a detailed report on Sheet Metal Component with good explanation on Sheet Metal modelling tools applied throughout the modelling. Also attach the Final model…

Advanced Sheet Metal Design Using NX Cad Challenge_5_Odd Shaped Enclosure     Objective-To study and learn the workflow procedure to design a Sheet Metal part for odd shapes’ using Siemens NX Sheet Metal Application.   Introduction-   What Is Sheet Metal?   According to a definition in a professional journal, it can be…

Advanced Sheet Metal Design Using NX Cad Challenge_6_Bracket     Objective-To design a Sheet metal Bracket in Sheet metal workbench of NX CAD Software Introduction-   What Is Sheet Metal?   According to a definition in a professional journal, it can be defined as: Sheet metal is a comprehensive cold…

Advanced Sheet Metal Design Using NX Cad Challenge_7_ Metal bracket-II     Objective-To design a Sheet metal Bracket-II in Sheet metal workbench of NX CAD Software Introduction-   What Is Sheet Metal?   According to a definition in a professional journal, it can be defined as: Sheet metal is a comprehensive…

                                                       Heat Stakes,Dog House  for the Door Trim   Objective-   To Create the Dog House, locators and heat stakes on A…