…

           MODELING OF SUNSEEKER PREDATOR 108 YACHT SOLIDWORKS   Objectives- The key objectives of this project are as follows:- To learn and understand the plethora of basic and advanced tools and / features available for creation of parts and assembly models in SOLIDWORKS To learn complex surfacing features in SOLIDWORKS.…

                                                                                           …

                                                               SHEET METAL DESIGN OF BOX ASSEMBLY USING SIEMENS NX-CAD OBJECTIVE: To design the sheet metal box assembly using siemens NX-CAD. INTRODUCTION: Sheet metal is a metal with a small thickness ranging from 0.5-6mm.Which is made flat and thin by rolling or hammering…

                                                                                          SHEET…

                                                                                  Modelling an Odd Shaped Enclosure in NX Sheet Metal   OBJECTIVE                            The objective of the project is to design a sheet metal odd shaped enclosure using Sheet metal application in Siemens NX and a drawing sheet needs…

                                                                               SHEET METAL DESIGN OF METAL BRACKET II USING…

                                                  UNDERBODY COATING UNDERBODY COATING:         Underbody coatings are those which are used to prevent car bodies against rust & corrosion. This underbody coating helps in protection from dust and moisture also some other factors such as poor road conditions, rocks getting…

                                                                                 CASE STUDY FOR BENCHMARKING TO BUY…

                                            DESIGNING OF CAR ENGINE HOOD USING NX-CAD   OBJECTIVE:      To create an outer and inner hood panel, positioning the striker, hinge, and their…

                                                                                       FENDER DESIGN…

                                         Section Modulus Calculation and Optimization of HOOD design   OBJECTIVE: To increase the Section Modulus of the hood by necessary changes using NX cad.  …

                                                        Roof Design and Analysis of Reinforcements Objectives:Create a Car Roof model based on the styling surface, master sections…

                                                              Design a BIW Back Door of the Car Using NX CAD OBJECTIVE:     To design a car backdoor using…

                                                                                           …

                                                                                          …

                                                                                   Coin Holder Design-Using NX-CAD…

                     DESIGN AND DRAFT ANALYSIS OF SWITCH BEZEL Aim: To create the Switch Bezel Plastic component through the given Class-A surface and also performing draft analysis on it at the end. Objective: To ensure proper tree structure is followed. Geometrical…

AIM:To create a switch bezel from the given A-class surface by considering a thickness of 2.5 mm and also creating Core and Cavity blocks for it. PROCEDURE: A class surface : The input of the product designer is in the form of the A-class surface. The job of the product designer is to create the B and C surfaces keeping…

                                                                                           …

      AIM: Create the boss and Dog House for the Centre console coin holder considering the design rules. OBJECTIVE: To create the Coin Holder Plastic Component. To create Class B and Class Surface and Tooling Axis. To create Solid Body from the Surface using Close Surface Feature. To create a Rib for the…

                                                                           Door Applique Design with Engineering Features Using CATIA…

AIM: To create a solid body of B pillar cover including ribs and locators using catia v5 tool using given A class surface and master section and adding thickness. INTRODUCTION : B-PillarThe B-pillar is the central pillar of the car. This pillar is actually a sheet metal part which is welded in the BIW of the car. The B-pillar…

                                                                                  DESIGN AND ASSEMBLY OF QUICK RETURN…

                                    Development of a Door Trim panel   Aim: To create solid body of Door trim panel including B side features and perform draft analysis from the given class A and Mastersections using CATIA. Door Trim panel: It is an interior component attached to the inner side of the door. This product…

                                                                                                      DOOR ARM REST BEZEL AIM: To create the door arm rest plastic component through the given Class A surface and at the end performing the draft analysis on the model. OBJECTIVES: To ensure proper tree structure is followed.…