Question 2 : Use a thermistor to sense the temperature of a heater and turn on or turn off the fan as per below. Answer:  Here we need to turn on the fan when the temperature is above 25C The blocks used are  Signal builder: used to build the signal that we require Controlled temperature source: Used to give…

Question 1: Implement stateflow of washing machine. Answer: The blocks used are  Chart: used to build the stateflow Display:used to display the result Lamp:from the dashboard and is used as an indicator. x  - power input y  - water input X  - Power ouput indicator  Y  - water output indicator…

Aim: To analyse the BAJA ATV vehicle performance and cvt ratios using various types of input and feedback methods. Blocks used: Signal builder: the brake and throttle input are given using the signal builder block. Simulink-PS converter:used to convert simulink signals to physical signals PS-Simulink converter:used to…

Question 1: Answer:Here when on cycle of ftp drive cycle is used the car cannot complete 45km.This is because one ftp cycle will cover only 11.04 km so here 4 cycles are used .It will not travel 45 km due to decreased battery capacity.   Question 2: Here the battery capacity is increased to 50 it travelled upto…

Question 1 Answer: Mapped model consists of predifined datas in lookup table.It does not depend on the real time situation and will deliver the same out put regardless of the current situation.But in dynamic mode a feed back is taken from the output so that real time situation is analysed and the input is provided accordingly.…

 Question 1: Answer: Different types of power converter circuits are AC to DC Converter (Controlled Rectifier) DC to DC Converter (DC Chopper) AC to AC Converter (AC voltage regulator) DC to AC Converter (Inverters) AC to DC Converter (Controlled Rectifiers)  A type of converter that changes input AC signal into…

Answer 1 ; A BJT is a bipolar juntion transistor having three terminals.When an input is applied between the two terminal an amplified or bigger size of the same signal is given as output between the other two terminals.In other words we can say that output can be controlled by the signal given at the base as input.It…

Answer 3: clear all close allclcspeed=linspace(0,2000,500);torque=linspace(0,500,200);kc = 0.1; % Copper Loss constantki = 0.002; % Iron Loss Constantkw = 0.0003; % Windage Loss ConstantCm = 25; % Motor Loss Constant[X,Y] = meshgrid(speed,torque);outpower=X.*Y;Totalloss = ((Y.^2).*kc)+ (ki.*X)+((X.^3).*kw)+Cm;inpower=outpower+Totalloss;E=outpower./inpower;cone=[0.70,0.72,0.75,0.77,0.79,0.80,0.81,0.82,0.83,0.84,0.85,0.86,0.87,0.88,0.89,0.90,0.91,0.92,0.93,0.95];contourf(X,Y,E,cone)colorbarxlabel('Speed…

Overview: The program is used to find the intersection and union of two linked list.The list is provided by the user.It will find the union and prints the list.For intersection it will give only one value as result.     #include<stdio.h> #include<stdlib.h> /* A structure of linked list node */struct…

#include <stdio.h>#include <stdlib.h>typedef enum{ gear_down, checking, moving_up, gear_up, lowering,}plane_status;typedef enum{ on, off,}s_s;typedef enum{ not_working, working,}h_c;typedef enum{ yellow, red, green}l_s;typedef enum{falling,raising}p_l;typedef struct{ char* current_status; char* light_status;…

Answer 1: Aircraft Empty Weight Max Fuel Weight Max Cargo Weight Max Gross Takeoff Weight Antanov AN-225 628,000 lbs285,000 kg 661,400 lbs300,000 kg 417,000 lbs190,000 kg 1,411,000 lbs640,000 kg Airbus A380-800 611,000 lbs277,000 kg 560,000 lbs254,000 kg 185,000 lbs84,000 kg 1,268,000 lbs575,000 kg Boeing 747-800 485,300 lbs220,100…

#include <avr/io.h> #define F_CPU 16000000L // #include "avr/interrupt.h" #include <util/delay.h>#define sw_dir (PIND & (1<<1)) // d1 pin is declared as push button for direction control.#define sw_dspd (PIND & (1<<2)) // d2 pin is declared as push button for speed control.#define…

#define echoPin 6#define triggerPin 7void setup() { pinMode(triggerPin, OUTPUT); pinMode(echoPin, INPUT); Serial.begin(9600); Serial.println("Ultrasonic Sensor HC-SR04 Test"); Serial.println("with Arduino UNO");}void loop() { long highPulseDuration; int calculatedDistanceCm; digitalWrite(triggerPin, LOW); delayMicroseconds(5);…

 Aim: Test plan to test features of a new mobile phone (Blackbox test) that needs to be implemented based on the following requirements.  Procedure All the test conditions are declared using else if.It will check for the condition in every…

Aim: To develop a PWM controlled fanload with DC motor. Blocks used H-bridge It is used as controller to controll the dc motor according to the gate pulses applied by Controlled PWM generator. Controlled PWM generator It is used to provide the gate pulses to the Hbridge Dc motor Dc motor is used to rotate the fan. Aero…

Live batch 1) Performed the static code review analysis 2) Performed integration testing  

Here 10 cells are connected in series and hence the voltage vill 72V and current will not change so current is 5.4Ah.As the battery model is identical parameters of only one battery is annalysed battery and  other cells are assumed same. A bus selector select the signals from the 'm' port of the generic battery and…

1) Initially calculations are done so as to find out the capacity of the battery. After deciding the capacity next step is to find out the number of series parallel combination of cell. Anode and cathode materials are selected based on their properties.   The terminals of the  batteries in series and parallel are spot…

Aim :Design and simulation of Buck converter for Auxiliary load in EV Given Input voltage is 48V, Output voltage is 12 V Load current is 10A The calculations are done on the to find the values of L C and R Vin=D*Vout where Vin- input voltage           Vout- output voltage        …

Aim: To understand energy analysis of EVs on different drive cycles. In this model an electric bike is used to understand the various energy requirements.   The various blocks used are  Drive cycle:It is used to give referrence drive cycle that is the input. Tire: The tire(magic formula) block is used for tire.…

Aim: To understand energy analysis of EVs on different drive cycles. In this model an electric bike is used to understand the various energy requirements.   The various blocks used are  Drive cycle:It is used to give referrence drive cycle that is the input. Tire: The tire(magic formula) block is used for tire.…

Drive cycle:It is used to give referrence drive cycle that is the input. Tire: The tire(magic formula) block is used for tire.   Gear: Simple gear is used to transfer the output torque from motor to the tire. DC motor The output torque is produced with the help of DC motor       Vehicle body: The vehicle…

  AIM: To design a battery pack for a car. Given cell parameters  capacity = 3500mAh=3.5Ah nominal voltage = 3.6V Given power =150kW so required current I = P/V I = 150000/120=1250A No of cells in series = Motor voltage /nominal voltage =120/3.6=33.3 Rounding off Case 1: No of cells = 33 Nominal voltage = nominal…

AIM : To estimate the heat generation and SOC of a battery for a given drive cycle Blocks used Battery: Generic battery block is used  Signal builder: The drive cycle is build using the signal builder which is then given as the input to the controlled current source. Controlled current source : It is used to drive…

AIM: Generate the interactive plot for the interpolated data and store them in a text file. Code: x=xlsread('VI.xlsx')V=x(:,1);I=x(:,2);vq=(-17.3:0.1:0.9);subplot(2,2,1);plot(V,I,'o');grid on;xlabel('voltage');ylabel('current');title('V vs I');yq1=interp1(V,I,vq);subplot(2,2,2);plot(V,I,'o',vq,yq1,'b.');grid on;title('Linear…

1) Fuel cells are classified primarily by the kind of electrolyte they employ. This classification determines the kind of electro-chemical reactions that take place in the cell, the kind of catalysts required, the temperature range in which the cell operates, the fuel required, and other factors. These characteristics,…

1) #include void setup() //Initialize the Serial Monitor with 9600 baud rate { Serial.begin(9600); Serial.println(F("In Setup function")); //use of F saves memory pinMode(LED_BUILTIN, OUTPUT); //Create two tasks with labels Task1, Task2 a //We also create the fourth task labeled as IdelTask when there is no task in //operation…

   Answer 1:-  False.  Ultracapacitors can be used as energy storage devices similar to a battery, and in fact are classed as an ultracapacitor battery. But unlike a battery, they can achieve much higher power densities for a short duration. They are used in many hybrid petrol vehicles and fuel…

The logic which is required in this is that if the power demand from the vehicle is less than the minimum FC power than the FC must go on standby and the power should be supplied from the battery storage system and if the power demand is greater than the min FC power than the FC should be used and if the power demand of…