1) Grade designation - M35, type of cement -opc 53grade, Type of admixture - fly ash, maximum nominal size of aggregate - 20mm, minimum cement content as per Is code 456 2000- 340kg, maximum cement content - 450kg, partial replacement of cement by fly ash - 30%, maximum w/c -0.45, slump - 100mma, chemical admixture - super…

1) Structural drawing required to be provided:- a) footing & column layout plan with schedule of footings, columns, plinth beam with grade of concrete and steel. b) Ground floor slab layout plan with slab steel schedule & for beam, staircase, balcony. c) Terrace floor slab layout plan with slab steel schedule &…

Challenge files are attached below

1) Draw lines with xline command & gives distances as per drawing and trim extra lines. Use mtext command for description of drawing. 2) Draw lines with xline command & gives distances as per drawing and trim extra lines. Use mtext command for description of drawing. 3) Draw lines with xline command &…

1) First of all set drawing units, limits & set zoom all. Draw drawing using line & circle command set angle as per drawing using tracking settings. 2) First of all set drawing units, limits & set zoom all. Draw drawing using line command setangle as per drawing using tracking settings. 3)  First…

1) First of set units, limits & zoom all. Set layer colour, line thickness for line, dimension, staircase, hatch, doors, windows, table, mtext & cup board block. Use rectangle command as per building outer size & give of 9'' offset to it,then select it & explode. Give offsets as per room dimensions & trim extra lines.…

In this session we going to how to make templates for drawing to give all details and set paper size to print. 1) First set units feets & inches, set limits & zoom all . Draw table as per drawing provided using line command. Make shape of bar using donut command. make ring shape using circle or arc command. Enter…

1) First of set units, limits and zoom all. Draft the drawing as per drawing. use command line , hatch, rectangle, spline, circle, mtwext & dt whereever required. 2) First of set units, limits and zoom all. Draft the drawing as per drawing. use command line , hatch, rectangle, spline, circle, mtwext &…

1) Set units, limits & zoom all. Draft the drawing as per provided measurements with comands xline, trim, offset, rec, parallel ofset, hatch. Make layer layer with continious, dashed line wherever required. Use multileader, dt text, multitext for description. 2) Set units, limits & zoom all. Draft the drawing…

1) First of set units, limits & zoom all . Draft for 20'x60' east facing plot. use commands line. offsts, paralllel, multileader, block & insert, multitext, creatate layers for lines. make plan, elevation, section, template for footing layout plan. center line drawing. make steel drawing using donut command for…

AIM & INTRODUCTION:- 1) To make template drawing for different clients as per paper size AO & make it as a block, to draft doors of different shapes & sizes & make it as a block. To make different shapes of steel and make it as a block & insert it in table. 1) First of use DWT FORMAT drawing file to…

Aim to & introduction of project :- To draft the drawing as per the drawing provided upgrade the drafting skill. To use new commands whereever possible. to short cut keys for faster drafting skills. To understand the & arrange the possible way provision appliances for kitchen layout.  1) First of all open dwg new dwg drawing…

1) First of all in model set scale 1:100, save view port in view tab, new view name it & define display boundry, click ok. In view manager click on your view port , set current, click apply & click ok. In work right click on it, click on from temple, click autocad templete click on tutorial m- Arch - dwt, now you…

Aim and introduction :-  My aim is to draft 3d drawing as per visiual ideas with proper sizes & dimension using different autocad 3d tools wherever required. Autocad is a 3 dimensional computer aided design is used for technical design & documentaion which replaces manual drafting with automated. We can assign…

aim& introduction :- To do models in 3d by as shown in challenge by using 3d commands. In this challege i had used commands like rectangle, move, copy, extrude, sweep, array, block,rotate, rotate 3d, union to make the model. Procedure:- 1) Open new drawing make settings for units, limits & zoom. Make 2d make in…

Aim & Introduction : My aim is to make moidel of 2 floor building using commands like rectangle poly lines, extrude, press pull, subtract, sweep, block,     First of set units, limits & zom all. Make layer for different elements of building. Make 2d plan of building in top plane with poly line &…

1) Click on file tab,clock on new, click on project, new project daialog box will appear, click on archtecturlal template, clivk ok. Save file as challenge 01. 2) In the file tab close the file & again open the file. Again open the file in revit home page. 3) In architecture tab, click on wall, click on on draw, click…

 Aim & introduction : - My aim is to create levels, grids, place wall elements as per size, show the model elements, know the concept of building information model, its uses,how the model is compared with engineering feilds like mep to avoid clashes to execute the building in proper way & to reduce cost implications.…

Aim & Introduction:- My aim is make a residential floor plan given as per dimensons provided place components & elements. Arrange the components in proper way to look in asthetic way. To place the floor in for different levels using copy to clip board. To create floor using floor tab, give thickness & apply…

KINDLY NOTE REVIT ARCHITECTURE FILE IS UP LOADING INTO THE BROWSER DUE TO FILE CAPACITY MORE. SO I COULD NOT UPLOADED THE REVIT ARCHITECTURE FILE I HAD UPLOADED PNG PHOTOS OF ALL VEIWS Aim& introduction : My aim is to model a residential building with all elements like walls, floors, slab, furniture, windows, doors,…

Kindly Due revit file capacity is more than 3gb the file is not uploading, so i had attached png files.  Aim & introduction:- I have created multistoried buildings of  2 towers comprising of 6 aparments of mixed 3 bhk @ 2bhk of 12 floors for each tower with parking at groung floor. the plot size is 60x70 mt leaving 9.0…

Aim & introduction :- In this project my aim is to learn short cut keys of various commads, create sheets for various elements like walls, columns, doors, windows, furniture elements like bed, table, dinining table, sofa, chairs, plumbing fixtures like cammode,sink, bath tub, wash basin, shower, curtain wall quatity,…

Aim & introduction:- In this project we come to know how save the revit project into nwc file & export it into navis work software. In navis work software we can make walk through of the project & look around all building , rooms elements & make the frames into video & save it. We can also…