Construction Geometrical set To split different surface part on various of geometrical set. Frist to create input geometrical set after to check it the class A surface boundary condition its not came any problem to move on forward. If problem will be come to short out after to create the input of class A surface. Class…

DEVELOPMENT OF DOOR TRIM PANEL INTRODUCTION:           Door panels serve as an interface between the interior of the car and the inner workings of the door, and between vehicle occupants and the door. They are expected to meet a variety of design specifications regarding…

AIM:             Download following connectors & Connector clip cad data from given link & define it as Electrical Connector using Electrical Part design Workbench. Define all the necessary properties to Connectors & Clip.   Deutsch DT06 – 08SA…

AIM: Q1. Download following cad data & define it as Electrical support using Electrical Part design Workbench. Define all the necessary properties.        P clamp Q2. Download following Back shell cad data & define it as Electrical back shell using Electrical Part design Workbench.…

Aim:      Q1. Route the following harness layout in Electrical workbench. Make assumption for harness bundle diameters. Use Following connectors as shown in layout diagram. Add protective covering on all branches connected to DT06-2S & DT06-4S connectors. Keep end extremity at 30mm (from connectors…

AIM:       Q1. Route the following harness layout in Electrical workbench. Make assumption for harness bundle diameters. Use the connectors provided. After completion of routing, Check the bundle Continuity. Add snap of result in submission Add annotation to all connectors. Make an assumption for…

Aim:      Q1. Flatten the harness assembly completed in “week 4 challenge”. Place the flattened view on drawing sheet. Ensure bundles with protective coverings has different visuals on drawing view. Process:    DT06-4S:         Bundle connection…

Aim: -            To route the wiring harness on given Engine and flatten view drawing in CATIA V5.   Objective: -              The objective of the project is to route the wiring harness on given V16 Engine…

Aim:         Route the Wiring Harness on given Car body and prepare flatten view drawing in Catia V5 Objective:                The objective of this project is to route the wiring harness and prepare flatten view drawing…

Benchmarking               Benchmarking is the continuous process of measuring products, services and practices against the toughest competitors or those companies recognized as industry leaders and application of significantly better practices that lead…

Underbody Coating          Underbody coating is usually a dense cladding (often based on rubber) applied uniformly to the undercarriage of the automobile. It is normally sprayed or painted on when the car is just out of the dealership and is clean. But even if you are getting the…

Hood Assembly Profile: Introduction         The hood or bonnet is the hinged cover over the engine of motor vehicles. Hoods can open to allow access to the engine compartment (or trunk on rear-engine and some mid-engine vehicles) for maintenance and repair. In design perspective hood should meet some specific conditions…

SECTION MODULUS OF THE HOOD Objective: To find the section modulus of the hood and optimisation to improve the overall section modulus. Section Modulus: The section modulus (S) is geometric property of the cross section used for designing beams and flexural members. It does not represent anything physically. Formula of…

AIM: -              Calculate the Wheel Arch gap at required points and check whether the car passes the European standar Wheel Arch Part File(.prt) Wheel Arch IGS File(.igs)       Introduction: -         Fender:                  Fender is a part of an automobile, motorcycle or other vehicle body that frames a wheel well.…

FENDER DESIGN: -                Fender is the Part of an automobile, motorcycle or other vehicle body that frames a wheel well (the fender underside). Its primary purpose is to prevent sand, mud, rocks, liquids, and other road spray from being thrown…

Introduction:              An automobile roof or car top is the portion of an automobile that sits above the passenger compartment, protecting the vehicle occupants from sun, wind, rain, and other external elements. Because the earliest automobiles were designed…

Design of Backdoor   Aim:        To design a backdoor of the car on sheet metal using the appropriate design and provided class A surface data by considering design parameters and make (Hinge, Gas stay, wiper mounting, latch & sticker) reinforcements and embosses.  Back Door:…