The material and reaction are write in following Table :-Li-ion battery is a type of rechargeable battery  Lithium-ion batteries are commonly used for portable electronics and electric vehicle  and are growing in popularity for military and aerospace applications. lithium battery:- The…

Working of Step for battery charge and discharge using UDDS data:-       To build a battery modelling of charge and discharge using UDDS data ,we have a two thing as follows:-  1. battery configuration 2. UDDS file       In battery configuration ,the battery are set to foolowing…

Coulomb counting method :-           Coulomb counting method is uesd to measure the dischrging current of a battery and the integrate the discharging current over time in order to estimate SOC. coulomb counting method is done to estimate the SOC(t) ,which is estimated fromthe discharging current…

Introduction:-  battery pack :- Battery is an electric device which is an assembly of electrical cell which contain the stored chemical  energy convert  into the elctric energy. each cell has positive terminal cathode and negative terminal cathode. these cell combine each other by series and parallel connection…

Introduction :-                       The Lithium-ion batteries are widely used as energy sources in different hybrid systems, however, the operation characteristics of the battery in such systems are strongly dependent on the operation temperature and therefore, with purpose to improve these characteristics a good thermal…

Simulink model of door bell by using solenoid block :- Construction of doorbell :-    1) In these doorbell model by using solenoid the different block is used are as :-  Battery  Switch  Ideal translational motion sensor  Pulse generator  Solenoid  Converter  Electrical reference…

The Model of Washing machine using stateflow in simulink :- component used in model:-               1) Chart               2) constant input block               3) Display                4) Lamp model Explatination:-              1) In these model we build a control logic for washing machine. These logic is build as per…

                                                         REPORT Aim:-                 A report carry out a system level simulation of an…

Power converter employ in electric and hybrid electric vehicle are as follows:- There are 3 main type of converter use in EV and HEV vehicle such as (DC-DC converter, AC- DC converter, DC-AC converter). AC- DC converter :-  1) These type of conveter are used to convert AC power into DC supply.These type of converter used…

Speed control of DC motor using BJT H-bridge:-                    In this model the speed of DC motor is control by the IGBT semiconductor device. The Bipolar junction transistor operate as an IGBT. When the IGBT start the conducting the voltage that is forward voltage appear across the emitter and collector region in…

1) Drive cycle :-                     A driving cycle is a series of data points representing the speed of a vehicle versus time. Driving cycles are produced by different countries and organizations to assess the performance of vehicles in various ways, as for…

Difference between mapped and dynamic model Engine , Generator and motor :- Mapped model :- Powertrain blockset provide two types of combustion engine model mapped and dynamic. Mapped engine represent macro engine behaviour as set of look up tables (brake torque , fuel flow, air mass flow , exhaust temperature , efficiency…

1) For EV default in file ,if cargo mass is 500 Kg with all other default condition, can the vehicle travel for 45Km with FTP drive cycle ?                 Load the Advisor tool in matlab command window and select metric system and load EV default in file and change the cargo weight…

1) Development of MATLAB Simulink model as per requirement. Requirement - 1: Steering wheel input as yaw rate (Signal name: SteeringWheel_YawDegreeInput) is the input for this system. This is compared against 3 angular values, one each for left turn, right turn & straight drive (Calibration Values: Right_Turn_AngularLimit,…

Traffic Jam Assistant Feature Introduction to the Feature: Traffic Jam Assistant is one of the most common feature in Advanced Driver Assistance System. Traffic Jam Assistant helps the driver arrive more relaxed at their destination, even in dense traffic or in traffic jams. As a partially automated comfort function, the…

Highway Assistant – Lane Changing Assistant Introduction to the Feature: The Highway Assistant supports the driver and takes over the longitudinal and lateral guidance of the vehicle in monotonous driving situations on highways. The partially automated function can automatically start, accelerate, brake as well as…

Aim :-          To Create a detailed MATLAB model of an electric rickshaw (three wheel passenger vehicle) Objective :- Rear wheels driven by PM brushed type motor Assume efficiency points of motor controller and motor Make an excel sheet of all input and assumed data  Results: For any three standard driving cycles show…

1. Compare four different types of fuel cells and state their applications? This classification determines the kind of electro-chemical reactions that take place in the cell, the kind of catalysts required, the temperature range in which the cell operates, the fuel required, and other factors. Types of fuel cell are as…