Calculate the Concrete Mix Design for M35 grade concrete with fly ash. Sol: Stipulation for proportion: Grade designation: M35 Type of cement: OPC 43 grade confirming to IS8112. Type of mineral admixture: Fly ash confirming to IS 3812 Maximum nominal size of aggregate: 20mm. Minimum cement content: 320Kg/m^3 (From…

  GROUND FLOOR       FIRST FLOOR:         GROUND FLOOR DIMENTION: 15514mmX7445mm ROOMS DIMENSION (in mm) Bedroom 3566 x 4430 Sit-out 3566 x 2525 Toilets 2216 x 1232 Washroom 1464 x 776 Living room 4130 x 3763 Kitchen 4038 x 3157 Parking 3447 x 3157     FIRST FLOOR DIMENTION:14075mm…

Aim: To design a residential building and draftn  Architectural drawing and Structural drawing . Plot Size: 60' x 20' Orientation: Facing East  ARCHITECTURAL DRAWING  A. Floor Plan : Ground Floor and First Floor   Procedure: 1. Architectural plan is first drafted in paper 2. Then the drawing is carried…

1.Aim: To draw a template. Template1 Procedure: The template is drawn by  the following tools:  lines  Offfset  Fillet   Text Create attributes Command:ATTDEF enter tag, promps and enter. Now the attributes are created. Attributes are created for entering the data. After entering the attributes…

1.AIM: Create layout of kitchen Procedure: Sketch the kitchen using the following tools Lines Circles Arcs Fillet Offset  Then turn on the layer tab: view>layout tabs Then the first drawing cand be seen in layout It can also be renamed    2. AIM:Create an elevation plan Procedure: Sketch elavation using…

1. AIM: To create the layout of a plan and section. Procedure: The floor plan: The elevation drawing; Go to layout tabs  Turn on the layout tab  Go to Layout in the ribbon Click on new  Select template m.Arch .dwt  Insert the template To adjust the size of icon use UCSICON command  The template…

1. Aim: Create a 3D furniture element. Procedure: To create a projection of the 3D element in X-Y axis According to the dimensions. Extrude it using extrude tool. Give the dimensions. The figure is in solids  Made by solids 2. Aim: Create 3D model of an isolated footing. Steps:  A rectangle is drawn with an assume…

1. Aim: Create a 3D Isometric View of the building  Steps: Create the plan from top view with wall of 9inch thick  Create a boundary using boundary command [BO] Extrude it with height of 10feet . Create a boundary on the window and extrude it. Join the wall and window extruded Create a region of the window…

AIM: To create a 3D rendered model for a residential building. Steps: 1. Walls: Create a 2D plan for the building.   Create a boundary for the walls. Extrude it Now create a layer for each element . Then extrude the windows boundary. Extrude it and union it.   2. Window: Create a 3D window using rotate,boundary,…

1) AIM: Create ceiling for the project model. Steps: Go to Architectural tab. Select floor plan. Select ceiling. draw the boundary line Select ok. Then the ceiling is created. Same for the first floor. Go to Architectural tab. Select first floor plan. Select ceiling. Sketch the boundary. Click ok. Thid is the 3D view of…

1. AIM: Type of structure. Soln: Office structure:  Area of 1856m2  Build up area is 526.03m3 No. of floors: 5 floors.   2. AIM; To write the geographic and location details for your project modeling. Soln:  Type of construction : 2 Plot size: 40mx70m Super Build up area :1856m2 (40mx46.4m). Open space…

Please find attachment :

Please find attachment.

(Please find attached) 

(please find attached)

Please find attached

Q1) Ans:- Investigation of the framing plan with respect to redundancy in X-direction.- Investigation of the framing plan with respect to redundancy in X-direction.Columns in X-Direction are comparatively more and evenly spaced. SO the structure is more redundant in X-Direction. Except the top and bottom column rows are…

(Please find attached)

Please find attached