Aim:- The work is focused on simulating fluid flow through an elbow channel duct containing a static throttle plate. Newtonian fluid, the air is considered as the working fluid for this project. The geometry will be exported as an STL file & modified using the various geometric editing tools available in Converge…

Aim:-  The work is focused on simulating fluid flow through a backward-facing step channel that will be designed using the various geometric editing tools available in Converge Studio. Air is considered as the working fluid. Boundary flagging technique is used to assign each side of the geometry to a particular boundary…

Aim:- The work is focused on simulating fluid flow using transient solver through an elbow channel duct containing a variable throttle plate. Newtonian fluid, the air is considered as the working fluid for this project. The pre-designed geometry will be exported as an STL file & modified using the various geometric…

Aim:- The work is focused on simulating fluid flow through a backward-facing step channel that would be subjected to a sudden increase in the cross-sectional area, this would result in flow separation & reattachment zones. The geometry will be designed using the various geometric editing tools available in Converge…

Abstract:- The work is focused on visualizing supersonic expansion fan technically known as Prandtl-Meyer shock waves, by allowing high-speed fluid to enter the geometry through an inlet duct followed by a sudden sharp corner, this sharp corner would create an infinite number of expansion waves or Mach lines which…

 Abstract:- The work is focused on setting up a flow simulation through an aluminum pipe to visualize the conjugate heat transfer mechanism between the pipe walls & the fluid flowing inside the pipe. We are interested in performing a grid-dependency test & also study the effects of super-cycling on simulation…

Objective:- In this paper, we discuss the importance of turbulence as a physical phenomenon and describe the main features of turbulent flow that are easily recognized & make it distinguishable from laminar flow. We follow this by introducing the 3 Navier Stokes Equations i.e. the Continuity Equation,…

Objective:- The experiment is focused on setting up a shock tube simulation using a transient flow solver to visualize shock waves generated due to the pressure difference created between the two regions when the diaphragm inside the tube is ruptured. Such an experiment is primarily useful in the study of chemical…

Abstract:- The experiment is focused on studying the flow characteristics over a symmetric NACA 2412 aerofoil inside a virtually designed low subsonic wind tunnel created using the geometry editing tools available in Converge CFD software & the results obtained will be post-processed using Paraview. The aerofoil…

Abstract:- The experiment is focused on studying the flow characteristics over an FSAE car inside a virtually designed low subsonic wind tunnel created using the geometry editing tools available in Converge CFD software & the results obtained will be post-processed using Paraview. This paper describes the…

Abstract:- The experiment is focused on studying the flow characteristics inside a T-junction. Temperature fluctuations occur due to the thermal mixing of hot and cold streams in the T-junctions. If this temperature gradient inside the T-junction is not monitored properly can lead to thermal fatigue of the piping. In…

Abstract:- Flow past a cylinder is one of the classical problems of fluid mechanics & the primary objective of this simulation is to perform external flow analysis for various Reynolds no (Re) over a 2-dimensional cylinder using both steady-state & transient solver. The flow is assumed to be 2D therefore…

Abstract:- The experiment is focused on investigating the flow characteristics over an AHMED body inside a virtually designed low subsonic wind tunnel created using the geometry editing tools available in SpaceClaim, apply multiple mesh refinement strategies i.e. perform grid scaling or grid independence test, assign…

ABSTRACT:- The purpose of this paper is to simulate a two-dimensional Rayleigh-Taylor instability problem using the classical method of Finite Volume analysis of a multiphase model using ANSYS FLUENT 20. The study focuses on setting up an experiment to visualize the Rayleigh Taylor instability problem which is…

ABSTRACT:- The purpose of this experiment is to perform Conjugate Heat Transfer (CHT) analysis on a hypothetical exhaust manifold of an IC engine using a pressure-based steady-state solver in ANSYS Fluent. The Exhaust manifold in the engines is an important component which has a considerable effect on the performance…

Abstract:- The work is focused on performing a steady-state, pressure-based conjugate heat transfer analysis on a hypothetical graphics card with appropriate user-defined materials. The term conjugate heat transfer (CHT) is used to describe a process that involves variations of temperature within solids and fluids,…

Abstract:- Cyclone separators are very useful equipment for particle removal from gaseous streams. Their simple design and low capital and maintenance costs have made cyclones one of the most widely used gas−solid separators. Their dynamic behavior includes several phenomena, such as vortex breakdown, a reversal…

Abstract:- In the current project, we shall study the mass flow rate at the outlet of a hypothetical gate valve for variable levels of lift of the gate disk. Gate valves are machine elements that are commonly used to control the flow of fluids through a long pipe. In construction, a gate valve consists of a circular gate…

Abstract:- The objective of the experiment is to perform a non-premixed combustion simulation on a hypothetical combustor model. A combustion reaction is when a substance reacts with oxygen and releases a huge amount of energy in the form of light and heat. The first required reactant in combustion is fuel. Many…

Abstract:- The experiment is focused on studying the flow characteristics over a symmetric NACA 0012 aerofoil inside a virtually designed low subsonic wind tunnel created using the geometry editing tools available in STAR CCM+ software & the results obtained will be post-processed using Plots & reports.…

When complex geometric structures with several smaller parts attached to it are imported to STAR CCM+ software, the software automatically converts the geometry surface into smaller triangles, while doing so the software encounters several issues such as the Pierced face, Open edge, Face quality, Face proximity & Non-manifold…

 Abstract:- The work is focused on writing a simple MATLAB/Octave code using functions to calculate the stoichiometric co-efficient (ar) for air-fuel ratio for alkane, alkene, and alkynes. Stoichiometric combustion offers an easy way to understand combustion concepts. When fuel and air mix they produce…

Abstract:- The work is focused on transforming Newtons 2nd Law of motion, which is in the form of a second-order differential equation into two ordinary differential equations (ODE) & writing a code using "ODE45" or "LSODE" function in MATLAB or Octave (depending on the programing language used) respectively to…

Problem Description 1. The function that needs to be computed, if f(x) = sin(x)/x^3 2. You will compute the first derivative at x = pi/3 for dx = pi/30. 2a. You will compute the derivative both numerically and analytically. Make sure you compute 1st, 2nd, and 4th order approximations. 3. Define an error parameter as the…

Problem Statement  1. For a range of dx, plot the first order, second and fourth-order error. dx range = [pi/4000,pi/40,20]  2. Make sure that you plot dx vs error in a way that makes sense. 3. Explain the results in the space provided. What can you say about the slope of the curves in this plot? 4. Write…

Problem Statement:-  Numerical solution to the One-dimensional Linear Convection equation. 1. Assume that the domain length is L = 1m 2. The initial velocity profile is a step function. It is equal to 2m/s between x= 0.1 and 0.3 and 1m/s everywhere else 3. Use first-order forward differencing for the time derivative…

Abstract:- The work is focused on performing a 2D Gear Sloshing simulation using a pressure-based transient solver for two different gearboxes having a clearance of 20% & 30% both filled with two phases of fluid. We will be running 4 different simulations each having a different percentage of immersions & materials…

  #User Defined Function (UDF) for Jacobi Method ----------------------------------------------------------------------------------------------------------------------------------------------------------------------------- function [jac_iter jac_error x] = Jacobi_function (L,d,U,B) x = zeros(3,1); x_old = x; jac_error…

Problem Statement:- 1. Steady-state analysis & Transient State Analysis Solve the 2D heat conduction equation by using the point iterative techniques that were taught in the class. The Boundary conditions for the problem are as follows; Top Boundary = 600 K Bottom Boundary = 900 K Left Boundary = 400 K Right Boundary…

Abstract:- The work is focused on writing a MATLAB/Octave code to simulate the isentropic flow through a quasi 1D supersonic nozzle using both the conservation and non-conservation forms of the governing equations and solving them using MacCormack's technique and compare their solutions by performing a grid dependency…

Abstract:- The work is focused on simulating fluid flow through a backward-facing step channel that would be subjected to a sudden increase in the cross-sectional area, this would result in flow separation & reattachment zones. The geometry will be designed by creating vertices & then joining them to form blocks.…

Objective:- The work is focused on performing a CFD simulation for a flow through a cylindrical pipe with reference to Hagen Poiseuille's principle that refers to the laminar flow formation inside a smooth cylindrical tube. Since the computation will be carried out on a laptop, we will not be able to consider the entire…

Surface Remeshing is one of the steps in the STAR CCM+ workflow. This feature can only be used once the Pierced Face, Open Edge & Non-manifold errors are resolved using the Surface Repair or Surface Wrap feature. Other errors such as the Face Quality & Proximity errors are resolved using this technique. Step…

Abstract:- The work is focused on editing the Mercedes-Benz truck using the geometry editing tools available in STAR-CCM+, rotating the truck trailer to align with the truck & finally creating a wind tunnel of adequate dimensions. We will be running 2 simulations, one with the trailer & the other without a…