ISRO Scientist/Engineer Mechanical 2023 paper: Part A, questions 61 to 80, solved

Questions 61 to 80 of the ISRO Scientist/Engineer 'SC' Mechanical written test of 7 Jan 2024 (Set A): 20 questions, each solved by Skill-Lync. ISRO never published an answer key for this test, so every answer was worked out three times independently and the disagreements were settled before publishing.

Question paper published by ISRO's Centralised Recruitment Board; answers and solutions by Skill-Lync (no official key exists) · Updated 19 Nov 2026 · 20 of 95 questions on this page

ISRO 2023 · Mechanical Set A · Q.61Part A · 1 mark · -0.33 if wrongMachine design

Torque a 4 mm fillet weld around a 50 mm shaft can carry

A 50 mm diameter solid shaft is welded to a flat plate all around by fillet weld of 4mm leg size as shown in Fig. If the allowable shear strength of the weld material is 100 MPa, the maximum approximate torque in Nm that the welded joint can sustain under pure torsion is
Td = 50 mmfillet weld, leg 4 mm, all round
  1. (a)
  2. (b)
  3. (c)
  4. (d)

Answer: (a) Skill-Lync answer; ISRO published no key

A fillet weld fails across its throat, the shortest section through the weld. For a 45 degree fillet of leg the throat is .

The weld is a thin ring of radius and throat round the shaft. Under pure torsion the shear stress in a thin ring is , so

.

In newton metres, .

Trap: using the 4 mm leg as the weld thickness gives , which is not an option. Options (b) and (c) print the same number, , so neither can be the answer.

Where this shows up in industry

Welded shaft-to-flange and bracket joints on launch-vehicle structures and gearbox housings are sized on the throat area, not the leg size.

ISRO 2023 · Mechanical Set A · Q.62Part A · 1 mark · -0.33 if wrongMaterials and manufacturing

Arc welding current for a triangular weld at 12 mm/s, 24 V

A weld with a triangular cross section as shown below is to be produced on a steel work piece by shielded metal arc welding operation using steel electrode. If a 24 V power supply is used and the welding speed is 12 mm/s, what is the current needed? Assume the efficiency as 80% and the specific energy to melt steel as 8 J/mm.
5 mm45°45°
  1. (a)
  2. (b)
  3. (c)
  4. (d)

Answer: (c) Skill-Lync answer; ISRO published no key

The figure marks 5 mm, taken here as the depth of the V-groove. The weld cross section is then a triangle 5 mm deep with 45 degree sides, so its top width is and its area is .

Weld metal produced per second: .

Melting power needed: . Only 80% of the electrical power reaches the work, so the arc power is .

Current: .

Where this shows up in industry

Heat input and current for a given groove area is how welding procedures are set for pressure vessels and propellant tank shells.

ISRO 2023 · Mechanical Set A · Q.63Part A · 1 mark · -0.33 if wrongEngineering mechanics

Absolute acceleration of a slider moving out on a rotating rod

A slider moving outward on a rod OR with a velocity of 3 m/s and acceleration of 9 m/s. The rod has an angular velocity of 7 rad/s counter clockwise about O and an angular acceleration of 12 rad/s clockwise. The magnitude of absolute acceleration of the slider at location A in m/s is
9 m/s²3 m/s7 rad/s12 rad/s²ORA1 m
  1. (a)20
  2. (b)50
  3. (c)67
  4. (d)79

Answer: (b) 50 Skill-Lync answer; ISRO published no key

Use polar components along and across the rod, with , , , (anticlockwise) and (clockwise).

Along the rod: .

Across the rod: . The second term is the Coriolis acceleration.

.

Where this shows up in industry

Radial plus Coriolis terms appear in robot arms, rotating launch-pad gantries and any link carrying a sliding actuator.

ISRO 2023 · Mechanical Set A · Q.64Part A · 1 mark · -0.33 if wrongEngineering mechanics

Spring stiffness for a satellite separation at 1 m/s relative speed

A satellite of mass 100 kg is attached centrally to the rocket stage of mass 900 kg using a separation system. In space the satellite is to be separated and ejected using 10 numbers of identical spring thrusters having same stroke of 30 mm. Assume springs are fully transferring the energy and angular body rate of the bodies are negligible after separation. What is the stiffness of the spring required to get the satellite axial relative velocity of 1 m/s.?
  1. (a)0.01 N/mm
  2. (b)10 N/mm
  3. (c)20 N/mm
  4. (d)100 N/mm

Answer: (b) 10 N/mm Skill-Lync answer; ISRO published no key

In space there is no external force, so momentum is conserved and the springs' stored energy ends up as kinetic energy of the two bodies. Let , and relative speed .

From momentum, and , giving and .

Kinetic energy: . The same value comes from with .

Ten springs, each compressed , store . Setting this to gives .

Where this shows up in industry

Spring-thruster separation systems on launch vehicles are sized exactly this way: the separation energy fixes the relative velocity, and the mass ratio fixes who moves.

ISRO 2023 · Mechanical Set A · Q.65Part A · 1 mark · -0.33 if wrongTheory of machines and vibrations

Speed ratio and direction in a four-gear train with two idlers

A gear train comprises of 4 spur gears – the driven gear G, two idlers G, G and the driving gear G. The radii of G, G, G and G are r, r/2, r/3 and 2r, respectively. What is the ratio of angular velocities of G to G and their direction of rotation?
  1. (a)Ratio = 1, opposite direction
  2. (b)Ratio = 1/6, same direction
  3. (c)Ratio = 2, Opposite direction
  4. (d)Ratio = 1/2, same direction

Answer: (c) Ratio = 2, Opposite direction Skill-Lync answer; ISRO published no key

At each mesh the pitch-line speeds are equal, so . Chaining :

.

Idler radii cancel, so they change only the direction, not the ratio. There are three meshes, an odd number, so turns opposite to .

Ratio , opposite direction

Where this shows up in industry

Idlers are used in actuator and drive-train layouts to bridge a distance or fix the output direction without changing the overall ratio.

ISRO 2023 · Mechanical Set A · Q.67Part A · 1 mark · -0.33 if wrongEngineering mechanics

Speed of an 8000 kg plane swinging down from 60 to 30 degrees

As shown in the figure, the plane, having a mass of 8000 kg, is hoisted back until and then the pull-back cable AC is released when the plane is at rest. Determine the speed of the plane just before it crashes into the ground at . (Neglect the size of the plane and effect of lift caused by the wings during the motion, assume g = 10 m/s)
OABCθ20 m
  1. (a)23.98 m/s
  2. (b)12.1 m/s
  3. (c)9.56 m/s
  4. (d)6.76 m/s

Answer: (b) 12.1 m/s Skill-Lync answer; ISRO published no key

With the cable released and lift neglected, the plane is a pendulum bob of length and tension does no work. Energy is conserved between (at rest) and , with measured from the vertical.

Drop in height: .

.

The 8000 kg mass cancels, so the answer does not depend on it.

Where this shows up in industry

Pendulum-type energy balances are used for drop and swing tests of landing gear, arrestor cables and hoisted hardware.

ISRO 2023 · Mechanical Set A · Q.68Part A · 1 mark · -0.33 if wrongEngineering mechanics

Load B that holds a ring with 27.3 kg at 45 and 60 degrees

A small ring Z carries vertical load A of mass 27.3 kg by two strings ZX and ZY. String ZY carries a load B at its free end through a frictionless pulley. Find the value of B (rounded to nearest integer), if the string is stable at the configuration shown in fig.
XY45°60°ZAB
  1. (a)14 kg
  2. (b)20 kg
  3. (c)10 kg
  4. (d)5 kg

Answer: (b) 20 kg Skill-Lync answer; ISRO published no key

The pulley is frictionless, so the tension in ZY equals the weight of B: . Let be the tension in ZX. Both angles are measured from the vertical.

Horizontal balance: , so .

Vertical balance: , so , i.e. .

.

Where this shows up in industry

Three-force joint equilibrium is the basis of rigging calculations for lifting satellites, cable-stayed structures and guy wires.

ISRO 2023 · Mechanical Set A · Q.69Part A · 1 mark · -0.33 if wrongStrength of materials

Strain in the steel part of a bar when aluminium reads 800 micro-strain

A solid bar 50 mm in diameter and 2000 mm long consists of a steel and aluminum part joined together. When axial force P is applied to the system, a strain gauge attached to the aluminum indicates an axial strain of 800 µm/m. What is the corresponding axial strain on the Steel? Assume E = 200 GPa and E = 70 Gpa.
  1. (a)28 µm/m
  2. (b)140 µm/m
  3. (c)280 µm/m
  4. (d)14 µm/m

Answer: (c) 280 µm/m Skill-Lync answer; ISRO published no key

The two parts are joined end to end in one 50 mm bar, so the same force acts on the same area and the stress is the same in both: .

From the aluminium reading, .

Steel strain: , that is .

Equivalent shortcut: strain is inversely proportional to , so . The lengths do not matter.

Where this shows up in industry

Strain-gauge readings on one member of a bi-material load path are converted to stress and then to the other material in joints and hybrid structures.

ISRO 2023 · Mechanical Set A · Q.70Part A · 1 mark · -0.33 if wrongMachine design

Maximum bolt tension with 30 Nm preload torque and 10 kN external load

Two flanges are connected by a single bolt of nominal diameter 10 mm and is preloaded to a torque of 30 Nm. An external tensile load of 10,000 N is applied to the joint. The torque coefficient is 0.15 and joint stiffness constant is 0.2. The maximum tension in the bolt is
  1. (a)10,000 N
  2. (b)20,000 N
  3. (c)22,000 N
  4. (d)30,000 N

Answer: (c) 22,000 N Skill-Lync answer; ISRO published no key

Preload from the tightening torque: , so .

With the joint constant , the bolt carries a fraction of the external load and the clamped members carry the rest:

.

Reading: the paper's phrase “joint stiffness constant” is taken as this standard joint constant (bolt share). If it meant the share taken by the members, the bolt tension would be 28,000 N, which is not an option.

Where this shows up in industry

Preloaded bolted flanges on engine mounts and tank interfaces are checked this way: most of the external load goes into relieving clamp force, not into the bolt.

ISRO 2023 · Mechanical Set A · Q.71Part A · 1 mark · -0.33 if wrongMetrology, CNC and industrial engineering

Minimum project completion time from a six-activity precedence table

For a particular project, six activities are to be carried out. The precedence relation and duration of activities are as per the following table. The minimum project completion time (in days) is
ActivityImmediate predecessorDuration (days)
A---6
BA5
CA8
DB11
EC6
FD, E7
  1. (a)32
  2. (b)27
  3. (c)29
  4. (d)30

Answer: (c) 29 Skill-Lync answer; ISRO published no key

The minimum completion time is the length of the longest path (the critical path). Compute the earliest finish of each activity:

  • A: 6
  • B: 6 + 5 = 11
  • C: 6 + 8 = 14
  • D: 11 + 11 = 22
  • E: 14 + 6 = 20
  • F starts after both D and E, i.e. at , and finishes at .

The two paths are A-B-D-F and A-C-E-F . The longer one, A-B-D-F, is critical. Adding all durations (43) or taking path A-C-E-F (27) are the usual traps.

29 days

Where this shows up in industry

Critical-path scheduling is used to plan launch-campaign and integration timelines, where only the longest chain of dependent tasks sets the date.

ISRO 2023 · Mechanical Set A · Q.72Part A · 1 mark · -0.33 if wrongTheory of machines and vibrations

Mobility of a cam and oscillating roller follower mechanism

A cam and oscillating follower mechanism is shown in the figure below. The Mobility of the mechanism is
  1. (a)-1
  2. (b)0
  3. (c)1
  4. (d)2

Answer: (d) 2 Skill-Lync answer; ISRO published no key

Count the links in the drawing: ground, cam, oscillating arm and the roller (a separate circle pinned to the arm), so .

Lower pairs (revolute): cam-ground, arm-ground and roller-arm, so . Higher pair: the roller-cam contact, so .

Grubler/Kutzbach: .

The second freedom is the roller spinning on its own pin, which does not affect the arm's motion. If the roller were treated as part of the arm, , , and . Since the figure draws the roller as its own pinned body, the formula result for this mechanism is 2.

Where this shows up in industry

Cam and roller followers drive valve trains and indexing mechanisms; the roller's idle spin is counted by the formula but ignored when analysing the output motion.

ISRO 2023 · Mechanical Set A · Q.73Part A · 1 mark · -0.33 if wrongStrength of materials

Normal and shear stress on the 45 degree plane of a biaxial element

A body is subjected to a bi-axial state of stress as shown in figure below: The magnitude of normal and shear stresses acting on the 45 degree plane in MPa
60 MPa60 MPa40 MPa40 MPa30 MPa30 MPa30 MPa30 MPa45°
  1. (a)50, 50 MPa
  2. (b)60, 40 MPa
  3. (c)40, 50 MPa
  4. (d)50, 30 MPa

Answer: (c) 40, 50 MPa Skill-Lync answer; ISRO published no key

Read the element: (tension, arrows pulling away from the left and right faces), (compression, arrows pushing into the top and bottom faces) and (the right face's shear points up and the top face's points right, the positive sense).

The 45 degree plane is the diagonal running from the top-left to the bottom-right corner, so its normal points up and to the right, at to the axis.

.

, a magnitude of .

(On the perpendicular diagonal the normal stress would be ; the shear magnitude stays 50.) Only option (c) fits.

Where this shows up in industry

Stress transformation to an inclined plane is how weld seams, bond lines and composite ply interfaces are checked under combined loads.

ISRO 2023 · Mechanical Set A · Q.74Part A · 1 mark · -0.33 if wrongMachine design

Ball bearing life when the load is doubled

If the load acting on the ball bearing is increased 2 times its life will
  1. (a)Reduce by 2 times
  2. (b)Reduce by 4 times
  3. (c)Reduce by 8 times
  4. (d)Not change

Answer: (c) Reduce by 8 times Skill-Lync answer; ISRO published no key

Bearing life in millions of revolutions follows , with exponent for ball bearings (and for roller bearings).

Doubling the equivalent load: .

So the life falls to one eighth.

Life reduces by 8 times

Where this shows up in industry

The cube law is why bearing loads on turbopumps and reaction wheels are kept well below rating: a small load increase costs a lot of life.

ISRO 2023 · Mechanical Set A · Q.75Part A · 1 mark · -0.33 if wrongMachine design

Engagement force of a clutch carrying 100 Nm, uniform wear

An old clutch is to transmit a torque of 100 N-m. The inner and outer diameter of the clutch plate is 100 mm and 200 mm respectively. The force required for engagement is (assume = 1/3 with uniform wear theory)
  1. (a)4 kN
  2. (b)10 kN
  3. (c)25 kN
  4. (d)50 kN

Answer: (a) 4 kN Skill-Lync answer; ISRO published no key

For uniform wear, pressure varies as and the axial force acts at the mean radius .

For one friction interface the torque is , so

.

The paper does not state the number of friction surfaces. One interface is the base case and is the only reading that gives an option (two surfaces would give 2 kN).

Where this shows up in industry

Clutch and brake sizing for actuator drives and automotive transmissions uses the uniform wear value because it is the safer (lower torque) estimate for worn plates.

ISRO 2023 · Mechanical Set A · Q.76Part A · 1 mark · -0.33 if wrongMachine design

Sommerfeld number ratio when radius doubles and clearance halves

A journal bearing of radius ‘r’and radial clearance ‘c’ has a sommerfeld number ‘s’. Another journal bearing of radius ‘r’ and radial clearance ‘c’ has a sommerfeld number ‘s’. All the other parameters remain the same for both bearings. If r= 2 r and c= c/2, then s/s
  1. (a)4
  2. (b)8
  3. (c)16
  4. (d)32

Answer: (c) 16 Skill-Lync answer; ISRO published no key

The Sommerfeld number is , where is viscosity, speed and the bearing pressure. With all other parameters unchanged, .

, so

.

Reading: “all other parameters” includes the bearing pressure , which is held equal.

Where this shows up in industry

The Sommerfeld number sets the film regime of journal bearings in turbopumps and engines, so radius and clearance changes are checked through it.

ISRO 2023 · Mechanical Set A · Q.77Part A · 1 mark · -0.33 if wrongStrength of materials

Match failure theories with the shape of their safe region

Match the following:
Column – I Theories of failureColumn – II Shape of region of safety
(A) Rankine Theory(i) Hexagon
(B) Tresca Theory(ii) Ellipse
(C) St. Venants theory(iii) Square
(D) Von mises Theory(iv) Rhombus
  1. (a)(A)-(ii), (B)-(iv), (C)-(i), (D)-(iii)
  2. (b)(A)-(iii), (B)-(iv), (C)-(ii), (D)-(i)
  3. (c)(A)-(iii), (B)-(i), (C)-(iv), (D)-(ii)
  4. (d)(A)-(iv), (B)-(i), (C)-(iii), (D)-(ii)

Answer: (c) (A)-(iii), (B)-(i), (C)-(iv), (D)-(ii) Skill-Lync answer; ISRO published no key

Plot each theory's safe region in the - plane (plane stress):

  • Rankine (maximum principal stress): , a square. A-(iii).
  • Tresca (maximum shear stress): in the mixed-sign quadrants, a hexagon. B-(i).
  • St. Venant (maximum principal strain): , a skewed four-sided figure, a rhombus. C-(iv).
  • Von Mises (distortion energy): , an ellipse. D-(ii).

This is the pairing in option (c).

A-(iii), B-(i), C-(iv), D-(ii)

Where this shows up in industry

Choosing between these failure criteria sets the margins quoted for ductile structural metals (von Mises or Tresca) and brittle ones (Rankine) in pressure parts and fittings.

ISRO 2023 · Mechanical Set A · Q.78Part A · 1 mark · -0.33 if wrongStrength of materials

Maximum bending stress in a 0.2 mm strip over a 25 mm pulley

A 0.2 mm thick strip is bent and laid over a frictionless pulley of 25 mm diameter. If E = 100 GPa, the maximum stress in the strip is
  1. (a)100 MPa
  2. (b)200 MPa
  3. (c)400 MPa
  4. (d)800 MPa

Answer: (d) 800 MPa Skill-Lync answer; ISRO published no key

Pure bending: . The outermost fibre is at from the neutral axis.

Taking the radius of curvature as the pulley radius :

.

A stricter value uses the radius to the strip's mid-thickness, , giving . Both round to option (d) because the strip is very thin compared with the pulley.

Where this shows up in industry

Thin foils, shims and flex circuits are limited by this stress when wrapped round a drum or reel, for example in deployable booms.

ISRO 2023 · Mechanical Set A · Q.79Part A · 1 mark · -0.33 if wrongFluid mechanics and turbomachinery

Pressure at (3, 3) in the flow V = k(x i - y j)

The velocity field of a certain two dimensional flow is given by where and and are in meters. If the fluid density is 100 kg/m and pressure at origin is 10 kPa, what is the pressure at point (3,3)?
  1. (a)3.2 kPa
  2. (b)6.4 kPa
  3. (c)1.6 kPa
  4. (d)None

Answer: (b) 6.4 kPa Skill-Lync answer; ISRO published no key

Components: and . The flow is steady, and , so it is irrotational and Bernoulli applies between any two points. Gravity is not mentioned and is neglected.

, with . At the origin (a stagnation point), so

.

At : , so .

Integrating Euler's equation, and , gives the same expression.

Where this shows up in industry

The pattern is the flow near a stagnation point, such as the nose of a vehicle or a pitot probe, where pressure rises toward the stagnation value.

ISRO 2023 · Mechanical Set A · Q.80Part A · 1 mark · -0.33 if wrongFluid mechanics and turbomachinery

Work done splitting a 2 mm water drop into 8 equal drops

A spherical water drop of diameter 2 mm splits in to 8 small drops of equal size in air at temperature of 25°C. The surface tension coefficient of water in air is 0.073 N/m and dynamic viscosity is 0.01 poise. The approximate work done in splitting up the drop is
  1. (a)
  2. (b)
  3. (c)
  4. (d)

Answer: (b) Skill-Lync answer; ISRO published no key

Work done equals surface tension times the increase in surface area. Viscosity does not enter.

Volume is conserved: , so , with .

Initial area: . Final area: .

Increase: .

.

A drop has a single liquid-air surface, so no factor of 2 is needed (that is for soap films).

Where this shows up in industry

Surface-energy bookkeeping sets droplet sizes in spray atomisers and propellant injectors: breaking liquid into smaller drops costs energy proportional to the new area.

From ISRO prep to a core mechanical career

Talk to a counsellor.

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.

Talk to a career counsellor

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.