ISRO Scientist/Engineer Mechanical 2023 paper: Part A, questions 21 to 40, solved

Questions 21 to 40 of the ISRO Scientist/Engineer 'SC' Mechanical written test of 7 Jan 2024 (Set A): 20 questions, each solved by Skill-Lync. ISRO never published an answer key for this test, so every answer was worked out three times independently and the disagreements were settled before publishing.

Question paper published by ISRO's Centralised Recruitment Board; answers and solutions by Skill-Lync (no official key exists) · Updated 19 Nov 2026 · 20 of 95 questions on this page

ISRO 2023 · Mechanical Set A · Q.21Part A · 1 mark · -0.33 if wrongMachine design

Effect of 10% more initial tension on flat belt power transmission

A flat belt run over a pulley and transmitting the power of 2.5 KW. The linear velocity of the belt is 2.5 m/s. The angle of lap is and the coefficient of friction between the belt and pulley is 0.3. If the initial tension of the belt is increased by 10%, what is the effect on power transmission? (neglecting the slip and centrifugal effect of the belt)
  1. (a)The power transmission is increased by 10 %
  2. (b)The power transmission is reduced by 10 %
  3. (c)The power transmission is doubled
  4. (d)The power transmission is reduced to half

Answer: (a) The power transmission is increased by 10 % Skill-Lync answer; ISRO published no key

With no slip and no centrifugal tension, the initial (static) tension is the mean of the two running tensions: . Power is .

On the point of slipping, . Here , so .

Substituting and gives

The factor depends only on and , which do not change. So the tension difference, and hence the power, is directly proportional to .

For the 2.5 kW case, (, ). Raising by 10% raises both tensions by 10%, so goes from 2.5 kW to 2.750 kW.

The power transmission is increased by 10 %.

The angle of lap and friction coefficient only fix the tension ratio. They do not decide the size of the power change.

Where this shows up in industry

Belt and chain drives for ground-support pumps, test-stand blowers and small vehicle accessories are tensioned by setting initial tension, which directly sets the torque they can carry before slipping.

ISRO 2023 · Mechanical Set A · Q.22Part A · 1 mark · -0.33 if wrongTheory of machines and vibrations

Natural frequency of a mass held between two identical springs

A mass is attached to two identical springs having stiffness as shown in figure below. The natural frequency of the vibrating system is
mkk
  1. (a)
  2. (b)
  3. (c)
  4. (d)

Answer: (b) Skill-Lync answer; ISRO published no key

One spring is above the mass and one below, each fixed at its far end. If the mass moves down by , the upper spring stretches and pulls it back up with , and the lower spring compresses and pushes it up with . Both forces oppose the displacement, so the springs act in parallel.

Option (a) is the frequency with only one spring. Springs in series (one spring between mass and wall, another between that spring and a second wall) would halve the stiffness, which is not this arrangement.

Where this shows up in industry

Spring-mounted instrument packages and isolation mounts on a launch-vehicle panel are often held by springs or elastomers on both sides, and the sum of their stiffnesses sets the mounting frequency that must stay clear of vehicle vibration bands.

ISRO 2023 · Mechanical Set A · Q.23Part A · 1 mark · -0.33 if wrongTheory of machines and vibrations

Damped spring-mass system after an impulse: which statement is true

A damped spring-mass system is forced to oscillate at by the application of an impulse force. Which of the following are true?
  1. (a)If the damping ratio is between 0 and 1, the system will show no oscillations
  2. (b)If the damping ratio is between 0 and 1, the system will eventually come to rest
  3. (c)If the damping ratio < 0, the system will eventually come to rest
  4. (d)The system will always oscillate

Answer: (b) If the damping ratio is between 0 and 1, the system will eventually come to rest Skill-Lync answer; ISRO published no key

After the impulse the system vibrates freely. With damping ratio and natural frequency , the roots of the characteristic equation are .

For the roots are complex with a negative real part. The response is : it oscillates inside a shrinking envelope and tends to zero, so the system eventually comes to rest.

  • (a) is false: underdamped motion oscillates.
  • (c) is false: with the real part of a root is positive, the envelope grows, and the motion never settles.
  • (d) is false: for the response returns to rest without oscillating.

Only (b) is true.

Where this shows up in industry

Damping ratio is the design number for structural dampers, shock struts and control-surface actuators: a ratio between about 0.3 and 0.7 gives a fast settle with a small overshoot after a gust or pyro-shock impulse.

ISRO 2023 · Mechanical Set A · Q.24Part A · 1 mark · -0.33 if wrongStrength of materials

Property giving the maximum strain energy absorbed before fracture

The property of the material that represents maximum amount of strain energy that it can absorb before it fractures under load is called:
  1. (a)Modulus of Resilience
  2. (b)Modulus of Toughness
  3. (c)Modulus of Elasticity
  4. (d)None of the above

Answer: (b) Modulus of Toughness Skill-Lync answer; ISRO published no key

Strain energy per unit volume is the area under the stress-strain curve, .

  • Area up to the elastic limit is the modulus of resilience: energy recoverable on unloading.
  • Area up to fracture is the modulus of toughness: the total energy absorbed before the material breaks.
  • The modulus of elasticity is just the slope of the straight part of the curve.

The property is the modulus of toughness.

Where this shows up in industry

Toughness drives material choice for impact-loaded parts such as landing-gear struts, crash structures and pressure-vessel shells, where absorbing energy before cracking matters more than raw strength.

ISRO 2023 · Mechanical Set A · Q.25Part A · 1 mark · -0.33 if wrongRefrigeration, air conditioning and psychrometrics

Carnot refrigerator COP with CFC, R-32 and ammonia between 300 K and 270 K

A Carnot refrigerator works in temperature range of 300 K to 270 K with different refrigerants CFC, R – 32 and ammonia. Which of the refrigerant give better COP?
  1. (a)CFC
  2. (b)R – 32
  3. (c)Ammonia
  4. (d)All gives same COP

Answer: (d) All gives same COP Skill-Lync answer; ISRO published no key

A Carnot (reversible) refrigerator has a coefficient of performance fixed by the two reservoir temperatures alone:

The working fluid does not appear in the formula. Any reversible refrigerator between the same two temperatures has the same COP, whether it uses CFC, R-32 or ammonia. The refrigerant matters in real cycles, through pressures, latent heat, and irreversibilities, but not in the ideal Carnot limit.

All the refrigerants give the same COP, .

Where this shows up in industry

The Carnot COP is the upper bound used to rate real chillers and cryocoolers; refrigerant choice then only decides how close a real machine gets to it and the pressures involved.

ISRO 2023 · Mechanical Set A · Q.26Part A · 1 mark · -0.33 if wrongThermodynamics and power cycles

Which diagrams represent the Stirling cycle (P-V and T-S)

Which of the following represent sterling cycle
Volume VP2341Volume vP2341pvγ = constantEntropy, ST2134V=CV=CEntropy ST2143IIIIIIIV
  1. (a)II
  2. (b)I and III
  3. (c)I and IV
  4. (d)All of the above

Answer: (c) I and IV Skill-Lync answer; ISRO published no key

The Stirling cycle has four processes: isothermal compression, constant-volume heating (regeneration), isothermal expansion, and constant-volume cooling (regeneration).

  • On a P-V diagram that is two constant curves joined by two vertical lines: this is diagram I.
  • On a T-S diagram the isotherms are two horizontal lines, joined by two curves of constant volume (): this is diagram IV.
  • Diagram II has constant-pressure lines and a constant expansion: that is not Stirling.
  • Diagram III has two vertical (isentropic) sides and two curves: that is the Otto cycle on a T-S diagram.

I and IV show the Stirling cycle.

Where this shows up in industry

Stirling engines and coolers run space cryocoolers and radioisotope-powered Stirling converters, since the regenerator gives high efficiency with a sealed working gas.

ISRO 2023 · Mechanical Set A · Q.27Part A · 1 mark · -0.33 if wrongFluid mechanics and turbomachinery

Rapid and sharp change of fluid properties in a very small region of gas flow

Rapid and sharp changes in fluid properties in a very small region of gas flow is known as
  1. (a)Cavitation
  2. (b)Shock wave
  3. (c)Sublimation
  4. (d)Chocking

Answer: (b) Shock wave Skill-Lync answer; ISRO published no key

A shock wave is a very thin region, only a few molecular mean free paths thick, across which pressure, density and temperature jump almost discontinuously while the flow speed drops. It appears in supersonic flow.

  • Cavitation: vapour bubbles in a liquid where static pressure falls to vapour pressure.
  • Sublimation: a solid turning directly to vapour.
  • Choking: the flow reaching Mach 1 at the minimum area, so mass flow cannot increase further. It limits the flow rate; it is not a sudden jump in properties.

The answer is shock wave.

Where this shows up in industry

Shock waves form in rocket nozzles, inlets and around the nose and fins of launch vehicles, and their location drives drag, heating and nozzle design.

ISRO 2023 · Mechanical Set A · Q.28Part A · 1 mark · -0.33 if wrongThermodynamics and power cycles

Entropy change when water is vaporised at 100 degrees C

What is the change in entropy when water is vaporized at . Latent heat of vaporization of water may be taken as 2238 kJ/kg.
  1. (a)22.38 kJ/kg K
  2. (b)2.238 kJ/kg K
  3. (c)6 kJ/kg K
  4. (d)100 kJ/kg K

Answer: (c) 6 kJ/kg K Skill-Lync answer; ISRO published no key

Vaporisation at constant pressure happens at constant temperature, so the process is reversible heat addition at a fixed : .

Use absolute temperature: .

Dividing by 100 (degrees Celsius) instead of 373 K is the trap that gives 22.38.

Where this shows up in industry

Steam-table entropy values like are used to size boilers and turbines in power plants and to check whether an expansion process is physically possible.

ISRO 2023 · Mechanical Set A · Q.29Part A · 1 mark · -0.33 if wrongThermodynamics and power cycles

Examine statements on work, heat engines and the Clausius statement

Examine the following statements:
(i) Work is high grade energy
(ii) It is possible for a heat engine to produce work in a cycle by exchanging heat with bodies at same temperature
(iii) It is impossible to construct a device which operating in a cycle will produce no other effect other than transfer of heat from a cooler to a hotter body
  1. (a)All statements are wrong
  2. (b)All statements are correct
  3. (c)Statements (i) and (iii) are correct
  4. (d)Statements (ii) and (iii) are correct

Answer: (c) Statements (i) and (iii) are correct Skill-Lync answer; ISRO published no key

  • (i) True. Work can be converted fully into heat, while heat can be converted into work only in part, so work is called high-grade energy.
  • (ii) False. A cycle exchanging heat with bodies all at the same temperature is a single-reservoir cycle. The Kelvin-Planck statement says no such cycle can produce net work.
  • (iii) True. This is the Clausius statement of the second law: heat does not flow from cold to hot, as the only effect, in a cyclic device.

Statements (i) and (iii) are correct.

Where this shows up in industry

These statements underlie why every heat engine and refrigerator needs two reservoirs and why spacecraft thermal systems must reject waste heat to a colder sink such as deep space.

ISRO 2023 · Mechanical Set A · Q.30Part A · 1 mark · -0.33 if wrongEngineering mechanics

Theorem on moment of the resultant of concurrent forces

The moment of resultant of concurrent forces with respect to a center in their plane is equal to the algebraic sum of the moments of components with respect to same center. This theorem is known as
  1. (a)Theorem of Varignon
  2. (b)Method of moments
  3. (c)Theorem of equilibrium of active forces
  4. (d)Theorem of three forces

Answer: (a) Theorem of Varignon Skill-Lync answer; ISRO published no key

This is the statement of Varignon's theorem: for a force system, the moment of the resultant about any point equals the sum of the moments of the individual forces about ,

The theorem of three forces is different: three coplanar forces in equilibrium must be concurrent (or parallel). The method of moments is a technique for solving equilibrium problems, not this theorem.

Where this shows up in industry

Varignon's theorem lets an engineer replace a distributed or multi-component load by one resultant, for example when computing the thrust-line offset moment on a rocket engine gimbal.

ISRO 2023 · Mechanical Set A · Q.31Part A · 1 mark · -0.33 if wrongMaterials and manufacturing

Identify brittle, ductile and plastic materials from three stress-strain curves

Stress strain curve of three types of material is given in the figure below. Please identify the correct combination.
StrainStressEFG
  1. (a)E - brittle, F - ductile, G - plastic
  2. (b)E - plastic, F - brittle, G - ductile
  3. (c)E - brittle, F - plastic, G - ductile
  4. (d)E - ductile, F - plastic, G- brittle

Answer: (a) E - brittle, F - ductile, G - plastic Skill-Lync answer; ISRO published no key

  • E climbs almost vertically (very stiff) and stops after a tiny strain with no flat yield region: it fractures with little plastic deformation, which is brittle behaviour.
  • F rises, then bends over and continues to a large strain at near-constant stress: it yields and stretches a long way before failing, which is ductile behaviour.
  • G is a horizontal line: the stress stays constant while the strain keeps growing. This is the idealised perfectly plastic material.

E is brittle, F is ductile, G is plastic.

Where this shows up in industry

Telling brittle from ductile behaviour decides whether a part gives visible warning (yielding) before it fails, which is why ductile alloys are preferred for primary structure and brittle ceramics are used only where loads are compressive.

ISRO 2023 · Mechanical Set A · Q.32Part A · 1 mark · -0.33 if wrongFluid mechanics and turbomachinery

Which quantity is the coefficient of momentum transport

Which is identified as the coefficient of momentum transport?
  1. (a)Density
  2. (b)Kinematic viscosity
  3. (c)Dynamic viscosity
  4. (d)Reynolds number

Answer: (b) Kinematic viscosity Skill-Lync answer; ISRO published no key

The three diffusive transport processes have matching diffusion coefficients: thermal diffusivity for heat, mass diffusivity for species, and kinematic viscosity for momentum. has units of , the same as and , and is also called the momentum diffusivity.

Density is a property and the Reynolds number is a dimensionless ratio, so neither is a transport coefficient.

Dynamic viscosity also governs momentum transport, but as the factor linking shear stress (momentum flux) to the velocity gradient. In the diffusion-coefficient language that pairs with and , the momentum coefficient is .

Kinematic viscosity is the best fit.

Note on this question Both kinematic viscosity (momentum diffusivity) and dynamic viscosity (the coefficient in Newton's law of viscosity, momentum flux per velocity gradient) are called a 'coefficient of momentum transport' in different textbooks. We take kinematic viscosity as the momentum diffusivity analogue of thermal diffusivity, but option (c) is arguable.

Where this shows up in industry

Kinematic viscosity sets how fast momentum diffuses in a boundary layer, so it enters Reynolds-number scaling for wind-tunnel tests and propellant line design.

ISRO 2023 · Mechanical Set A · Q.33Part A · 1 mark · -0.33 if wrongFluid mechanics and turbomachinery

Most economical depth of flow in an open rectangular channel

Which is the most economical depth of flow in an open rectangular channel?
  1. (a)Depth of flow equals to the width of channel
  2. (b)Depth of flow is double the width of channel
  3. (c)Depth of flow is half of the width of channel
  4. (d)Depth of flow is 1/3rd the width of channel

Answer: (c) Depth of flow is half of the width of channel Skill-Lync answer; ISRO published no key

The most economical (best hydraulic) section carries the most flow for a given area, which means the least wetted perimeter for that area .

For a rectangle of width and depth : and . Substituting :

So , giving , or . The hydraulic radius is then .

The depth of flow is half the width of the channel.

Where this shows up in industry

Best-hydraulic-section sizing is used for irrigation canals, drainage channels and test-facility flumes, where it minimises lining material for a required discharge.

ISRO 2023 · Mechanical Set A · Q.34Part A · 1 mark · -0.33 if wrongStrength of materials

Shear force and bending moment expressions for a beam under uniform load

A beam is subjected to the uniform load per unit length and , & are the reactions as shown in the figure. The expression for shear force and Bending moment is given by
yWc N/mABxMAVAVB
  1. (a)
  2. (b)
  3. (c)
  4. (d)

Answer: (d) , Skill-Lync answer; ISRO published no key

Cut the beam at distance from A and look at the left piece. The upward reaction acts at A; the downward load on the piece is , acting at its centre, from the cut.

Vertical equilibrium (taking up as positive) gives the shear:

Taking moments about the cut, has lever arm and the load has lever arm , with the load's moment opposing 's. Adding the end moment (the bending moment at ):

Consistency test: , as the relation between moment and shear requires. Options (a) and (c) have in the shear, which would mean the downward load adds to an upward reaction. Options (b) and (c) have , which has the wrong sign against .

and .

Where this shows up in industry

Shear and moment diagrams for distributed loads are the first step in sizing wing spars, launch-vehicle skin-stringer sections and pipe supports.

ISRO 2023 · Mechanical Set A · Q.35Part A · 1 mark · -0.33 if wrongStrength of materials

Elastic curve of a cantilever with an end bending moment M1

Determine the equation of the elastic curve for the cantilever beam of uniform cross section as shown in the figure due to the applied bending moment (Consider Young’s modulus as E and Moment of inertia as I)
YXM1L
  1. (a)
  2. (b)
  3. (c)
  4. (d)

Answer: (c) Skill-Lync answer; ISRO published no key

A moment applied at the free end of a cantilever is carried unchanged along the whole length, so is constant. The beam equation is

Integrate once: . At the fixed end () the slope is zero, so .

Integrate again: . At the fixed end the deflection is zero, so .

The curve is a parabola, so the tip deflection is . The moment in the figure bends the beam upward, so is positive in the Y direction shown.

Where this shows up in industry

End-moment cantilever results are used to estimate tip deflection of a boom, antenna mast or satellite appendage loaded by a motor or reaction-wheel torque at its free end.

ISRO 2023 · Mechanical Set A · Q.36Part A · 1 mark · -0.33 if wrongMaterials and manufacturing

Preferred steel microstructure for cryogenic applications

The preferred choice of the steel material for Cryogenic application is
  1. (a)Ferrite
  2. (b)Austenitic
  3. (c)Martensite
  4. (d)All the Above

Answer: (b) Austenitic Skill-Lync answer; ISRO published no key

Steels with a body-centred cubic (BCC) lattice, namely ferritic and martensitic grades, show a ductile-to-brittle transition: below a certain temperature the impact toughness collapses and the steel can fracture suddenly.

Austenitic steels (for example 304 and 316 stainless) have a face-centred cubic (FCC) lattice with many slip systems. They stay tough and ductile down to liquid-nitrogen and even liquid-helium temperatures, with no brittle transition.

Austenitic steel is the preferred choice.

Where this shows up in industry

Austenitic stainless steel is used for liquid-oxygen, liquid-hydrogen and liquid-nitrogen tanks, lines and valves on launch vehicles and ground fuelling systems.

ISRO 2023 · Mechanical Set A · Q.37Part A · 1 mark · -0.33 if wrongMaterials and manufacturing

Kind of deformation that occurs in shape memory alloys

What is the kind of deformation that occurs in shape memory alloys?
  1. (a)Thermo Plastic
  2. (b)Plastic
  3. (c)Thermo Elastic
  4. (d)None

Answer: (c) Thermo Elastic Skill-Lync answer; ISRO published no key

Shape memory alloys such as Nitinol (NiTi) deform through a reversible, thermoelastic martensitic transformation. In the cool martensite phase the alloy can be deformed by detwinning, which looks like plastic strain. Heating above the transformation temperature returns it to austenite and the original shape is recovered. Above that temperature, large strains also recover on unloading (superelasticity).

So the deformation is recoverable through temperature change: thermo-elastic. Ordinary plastic deformation would stay put, and thermoplastic is a polymer term.

The deformation is thermo-elastic.

Where this shows up in industry

NiTi actuators and release devices are used in spacecraft for solar-array and antenna deployment, where heating the element returns it to its programmed shape without a motor.

ISRO 2023 · Mechanical Set A · Q.38Part A · 1 mark · -0.33 if wrongTheory of machines and vibrations

Damping ratio of a system with equation x'' + 4x' + 16x = 12 sin 5t

The equation of motion of a spring-mass-damper system is given by . What is the damping factor of the system?
  1. (a)1
  2. (b)0.5
  3. (c)0.25
  4. (d)0.75

Answer: (b) 0.5 Skill-Lync answer; ISRO published no key

Divide the standard form by to get .

Matching with :

The right-hand side is the forcing term and has no effect on the damping ratio.

Where this shows up in industry

Damping ratio is read straight from the equation of motion when tuning suspension dampers, vibration isolators and control-surface actuators, with 0.5 giving a quick, mildly oscillatory response.

ISRO 2023 · Mechanical Set A · Q.39Part A · 1 mark · -0.33 if wrongMachine design

Location of maximum shear stress in the wire of a loaded helical spring

A round wire helical spring is loaded by the axial force. The maximum shear stress in the wire cross section will be at
  1. (a)Outer fibre
  2. (b)Inner fibre
  3. (c)Center of the cross section
  4. (d)Both outer and inner fibres

Answer: (b) Inner fibre Skill-Lync answer; ISRO published no key

An axial load on a helical spring twists the wire. Every wire cross section carries a torque plus a direct shear force .

Torsional shear is largest at the wire surface: . Direct shear is . On the inner side of the coil (the fibre nearest the spring axis) the direct shear acts in the same direction as the torsional shear, so they add. On the outer side they subtract.

For example, with , , : inner , outer .

The curvature of the coil raises the inner-fibre stress further (the Wahl correction), while the centre of the wire section has zero torsional shear.

The maximum shear stress is at the inner fibre.

Where this shows up in industry

Spring cracks start at the inside of the coil, so valve springs, landing-gear and separation springs are shot-peened there to extend fatigue life.

ISRO 2023 · Mechanical Set A · Q.40Part A · 1 mark · -0.33 if wrongMachine design

Stresses in a shaft carrying a mid-span spur gear with 20 degree pressure angle

The power is transmitted through a spur gear with pressure angle mounted at the mid span of shaft supported on bearings at the ends. The nature of stress induced in the shaft is
  1. (a)Normal stress due to bending only.
  2. (b)Normal stress due to bending and shear stress due to torsion.
  3. (c)Normal stress due to bending, axial loading and shear stress due to torsion
  4. (d)Normal stress due to axial loading and shear stress due to torsion

Answer: (b) Normal stress due to bending and shear stress due to torsion. Skill-Lync answer; ISRO published no key

The tooth contact force on a spur gear lies in the plane of the gear. It splits into a tangential component (which carries the power) and a radial component .

  • Both and act at right angles to the shaft axis, at mid-span between the bearings. They bend the shaft, giving normal (bending) stress.
  • also acts at the gear radius, so the shaft transmits a torque , giving shear stress due to torsion.
  • A spur gear has straight teeth, so there is no axial thrust. Axial load appears only with helical or bevel gears.

The shaft sees normal stress due to bending and shear stress due to torsion.

Where this shows up in industry

Gearbox shafts for actuators, pumps and test rigs are sized for combined bending and torsion using the maximum-shear or distortion-energy criterion.

From ISRO prep to a core mechanical career

Talk to a counsellor.

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.

Talk to a career counsellor

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.