ISRO Scientist/Engineer 'SC' Mechanical 2025 question paper, solved with the final answer key

ISRO's written test for Scientist/Engineer 'SC' (Mechanical), held on 26 October 2025, question by question. Every answer follows ISRO's revised final key, every solution is worked out in full by Skill-Lync, and the six answers ISRO changed after objections are marked. Use it to see exactly what ISRO asks before the next written test.

Question paper and answer keys published by ISRO's Centralised Recruitment Board; solutions by Skill-Lync · Updated 18 Nov 2026 · 20 of 95 questions on this page

How many questions were in the ISRO Scientist/Engineer Mechanical 2025 paper?

95 multiple-choice questions in two parts, written on 26 Oct 2025. Part A had 80 mechanical engineering questions of 1 mark each, with 0.33 deducted for a wrong answer. Part B had 15 aptitude questions worth 20 marks, with no negative marking. ISRO later excluded Q82 from evaluation and revised 6 answers after objections.

Which subjects carried the most marks?

Counting the 80 Part A questions by subject: materials and manufacturing 14, fluid mechanics and turbomachinery 13, theory of machines and vibrations 11. Together that is 38 of 80 technical marks. The remaining questions spread over 7 more subjects; the table below links every question.

What was the cut-off for this paper?

The Mechanical paper was evaluated out of 99 (80 + 19, after the excluded question). The last candidate short-listed for interview, other than PwBD, scored 55.70 (PwBD 50.39), and every candidate also needed 40 in Part A and 9.5 in Part B. ISRO short-listed 744 candidates and empanelled 148.

Questions by subject, ISRO Mechanical 2025 (Set A), counted by Skill-Lync
SubjectQuestionsQuestion numbers
Materials and manufacturing141819225356575960616263667475
Fluid mechanics and turbomachinery1323456714151644525564
Theory of machines and vibrations112429424345464748497379
Heat transfer91921273033407180
Thermodynamics and power cycles8810111213365865
Strength of materials82023353839415051
Metrology, CNC and industrial engineering86768697072767778
Engineering mechanics417283132
Machine design425263437
Engineering mathematics154
Aptitude: reasoning and verbal9828388899091939495
Aptitude: quantitative6818485868792

ISRO 2025 · Mechanical Set A · Q.1Part A · 1 mark · -0.33 if wrongHeat transfer

Useful heat from an uncovered flat plate solar collector with a selective absorber

A flat plate solar collector with no cover plate has a selective absorber of emissivity 0.2 and solar absorptivity 0.95. At a given time of day the absorber surface temperature is when the solar irradiation is , the effective sky temperature is and the ambient air temperature is . Assume the heat transfer convection coefficient to be . Calculate the useful heat removal rate from the collector. The sky radiation is in the same spectral region as that of surface emission.
  1. (a)
  2. (b)
  3. (c)
  4. (d)None of the above

Answer: (b) Official final key: (b)

Energy balance on the absorber per unit area: useful heat equals solar energy absorbed, minus net long-wave radiation to the sky, minus convection to the ambient air.

The sky radiation lies in the same long-wave band as the surface's own emission, so the absorber absorbs it with absorptivity equal to its emissivity, 0.2. That is why one multiplies both and . The high solar absorptivity 0.95 applies only to the incoming sunlight.

With , and :

  • Absorbed solar:
  • Net radiation:
  • Convection:

, so , option (b). Using 273.15 instead of 273 for the kelvin conversion gives , still (b), so (d) is not needed.

Where this shows up in industry

Spacecraft thermal engineers run the same balance with a surface's solar absorptivity and infrared emissivity (its ratio) to size radiators and choose coatings; selective coatings on solar water heaters use a low emissivity in the same way to cut radiation loss.

ISRO 2025 · Mechanical Set A · Q.2Part A · 1 mark · -0.33 if wrongFluid mechanics and turbomachinery

Weight lifted by a hydraulic press with a 30 cm ram and a 4.5 cm plunger

A hydraulic press has a ram of 30 cm diameter and a plunger of 4.5 cm diameter. Find the weight lifted by hydraulic press when force applied at plunger is 500 N.
W F 30 cm 4.5cm
  1. (a)3.33 KN
  2. (b)22.22 N
  3. (c)3.33 N
  4. (d)22.22 KN

Answer: (d) 22.22 KN Official final key: (d)

Pascal's law: the pressure under the plunger is transmitted unchanged to the ram, so .

, so , option (d) (the paper writes KN for kN).

Trap: using the diameter ratio without squaring gives , option (a). Force scales with area, which goes as the diameter squared.

Where this shows up in industry

Hydraulic presses for forging, deep drawing and composite moulding, and hydraulic jacks and brake systems, all use this area-ratio force multiplication; the price is that the ram moves only as far as the plunger.

ISRO 2025 · Mechanical Set A · Q.3Part A · 1 mark · -0.33 if wrongFluid mechanics and turbomachinery

Density of an iceberg that floats 90% submerged in sea water of 1025 kg/m3

90% of an iceberg volume is below the surface of sea water and only 10% is visible above surface. Find the density of iceberg, if density of sea-water is .
  1. (a)
  2. (b)
  3. (c)
  4. (d)

Answer: (c) Official final key: (c)

For a floating body, weight equals buoyancy (Archimedes): the weight of the whole iceberg equals the weight of sea water displaced by the submerged 90%.

, so , option (c).

In general the submerged fraction of a floating body equals the ratio of its density to the liquid's density. Option (d) would mean the iceberg floats fully submerged, and (a) and (b) are above 0.9 of the sea-water density.

Where this shows up in industry

The same submerged-fraction rule sets the draught of ships and floating platforms and is used to size buoyancy tanks for recovering sea-splashdown hardware such as crew modules and booster parts.

ISRO 2025 · Mechanical Set A · Q.4Part A · 1 mark · -0.33 if wrongFluid mechanics and turbomachinery

Shear stress 15 cm from a plate for the velocity profile u = 2y - y^2 and 8.60 poise

The equation of a velocity distribution over a plate is given by , where is the velocity in m/s at a point meter from the plate measured perpendicularly. Assuming poise, the shear stress at a point 15 cm from the boundary is
  1. (a)14.6 Pa
  2. (b)0.24 Pa
  3. (c)2.4 Pa
  4. (d)1.46 Pa

Answer: (d) 1.46 Pa Official final key: (d)

Newton's law of viscosity: .

Velocity gradient: . At : .

Viscosity in SI units: , so .

, so , option (d).

Trap: forgetting the poise conversion gives , option (a).

Where this shows up in industry

Wall shear stress from a measured or computed velocity gradient is how engineers get skin-friction drag on wings and launch-vehicle fairings and the viscous loss in lubricated bearings.

ISRO 2025 · Mechanical Set A · Q.5Part A · 1 mark · -0.33 if wrongFluid mechanics and turbomachinery

Terminal velocity of a lamina sliding down an inclined plane on a thin oil film

A thin plane Lamina, of Area A and weight W, slides down a fixed plane inclined at an angle and maintains a uniform gap from the surface of the plane, the gap being filled with oil of constant viscosity . The terminal velocity of the plane is :
Lamina Oil α ε
  1. (a)
  2. (b)
  3. (c)
  4. (d)

Answer: (b) Official final key: (b)

At terminal velocity the lamina no longer accelerates, so the component of its weight along the plane is balanced by the viscous shear force from the oil film.

In a thin film the velocity varies linearly from 0 at the fixed plane to at the lamina, so the shear stress is and the shear force is .

Therefore , option (b).

Option (a) uses , the weight component normal to the plane, which is carried by the film pressure and does not drive the motion. Options (c) and (d) are dimensionally wrong: they do not have units of velocity.

Where this shows up in industry

This is the basic model behind hydrodynamic slider bearings and viscous dampers, and behind viscometers that time a body sliding or falling through a thin oil gap.

ISRO 2025 · Mechanical Set A · Q.6Part A · 1 mark · -0.33 if wrongFluid mechanics and turbomachinery

Velocity of an oil stream from a bent glass tube showing a 50 mm rise

A glass tube with a 90° bend is open at both the ends. It is inserted into a flowing stream of oil, with specific gravity 0.9, so that one opening is directed upstream and the other is directed upward. Oil inside the tube is 50 mm higher than the surface of flowing oil. The velocity measured by the tube is, nearly :
  1. (a)1.99 m/s
  2. (b)0.99 m/s
  3. (c)2.99 m/s
  4. (d)3 m/s

Answer: (b) 0.99 m/s Official final key: (b)

The bent tube is a simple Pitot tube. At its upstream-facing mouth the oil is brought to rest, so its kinetic head is converted to a rise of the same oil in the tube.

, so , option (b).

The specific gravity 0.9 does not enter: the rise is measured in the same oil that is flowing, so density cancels. It would matter only with a manometer filled with a different liquid.

Where this shows up in industry

Pitot and Pitot-static probes measure airspeed on aircraft and flow velocity in wind tunnels and test-stand feed lines; the same stagnation-pressure idea is used in flow meters for liquid propellant lines.

ISRO 2025 · Mechanical Set A · Q.7Part A · 1 mark · -0.33 if wrongFluid mechanics and turbomachinery

Gauge pressure inside a 1.6 mm rain drop with surface tension 0.073 N/m

If the surface tension of water-air interface is 0.073 N/m, the gauge pressure inside a rain drop of 1.6 mm diameter is
  1. (a)182 Pa
  2. (b)0.182 Pa
  3. (c)91 Pa
  4. (d)0.091 Pa

Answer: (a) 182 Pa Official final key: (a)

A liquid drop has one free surface. A force balance on half the drop gives , so .

, so , option (a).

Trap: writing (diameter in place of radius) gives , option (c). A soap bubble, with two surfaces, would have .

Where this shows up in industry

Capillary pressure governs droplet size in fuel injectors and sprays, and surface-tension propellant management devices in spacecraft tanks use it to keep liquid at the tank outlet in microgravity.

ISRO 2025 · Mechanical Set A · Q.8Part A · 1 mark · -0.33 if wrongThermodynamics and power cycles

COP of a Carnot refrigerator between the limits of a 25% efficient Carnot engine at 400 K

A Carnot engine receiving heat at 400 k has an efficiency of 25%. What is the COP of a Carnot refrigerator working between same temperature limits?
  1. (a)1
  2. (b)2
  3. (c)3
  4. (d)4

Answer: (c) 3 Official final key: (c)

Carnot engine: , so .

Carnot refrigerator between the same limits: , so , option (c).

Shortcut: . Option (d), 4, is , the COP of a Carnot heat pump, not a refrigerator.

Where this shows up in industry

Carnot COP is the ceiling against which real refrigeration plants, cryocoolers for infrared detectors on satellites and HVAC chillers are benchmarked.

ISRO 2025 · Mechanical Set A · Q.9Part A · 1 mark · -0.33 if wrongHeat transfer

Time for a 1 mm thermocouple junction to read 99% of the initial temperature difference

The temperature of a gas stream is to be measured by a thermocouple whose junction can be approximated as a 1-mm-diameter sphere. The properties of the junction material are , , and specific heat and the convective heat transfer coefficient between the junction and the gas is . Determine how long it will take for the thermocouple to read 99 percent of the initial temperature difference.
  1. (a)10.5 s
  2. (b)5.3 s
  3. (c)21 s
  4. (d)15 s

Answer: (a) 10.5 s Official final key: (a)

Check whether lumped analysis applies. For a sphere , so , far below 0.1. The junction temperature is uniform.

Lumped response: with time constant .

Reading 99% of the initial difference means only 1% of it remains: .

, so , option (a).

Where this shows up in industry

Thermocouple time constants decide whether a sensor can follow fast transients, for example gas temperatures in engine test beds or in a rocket motor's ground firing, where a slow junction would average out the peaks.

ISRO 2025 · Mechanical Set A · Q.10Part A · 1 mark · -0.33 if wrongThermodynamics and power cycles

Gas turbine cycle efficiency with 600 kJ/kg turbine and 400 kJ/kg compressor work

In a gas turbine cycle, the turbine output is 600 KJ/kg and the compressor work is 400 KJ/kg. If the heat supplied is 1000 KJ/kg, what is the thermal efficiency of this cycle?
  1. (a)80%
  2. (b)60%
  3. (c)40%
  4. (d)20%

Answer: (d) 20% Official final key: (d)

Thermal efficiency is net work over heat supplied, and the compressor absorbs part of the turbine output.

, option (d).

Trap: dividing the turbine output alone by the heat supplied gives 60%, option (b). The compressor work is large in a gas turbine (here two thirds of the turbine output), which is why its back work ratio matters so much.

Where this shows up in industry

High back work ratio is the defining feature of Brayton-cycle machines such as aero engines, industrial gas turbines and the turbopumps of liquid rocket engines.

ISRO 2025 · Mechanical Set A · Q.11Part A · 1 mark · -0.33 if wrongThermodynamics and power cycles

Boiler efficiency from 205 kg/h feed water, 23 kg/h coal and 2050 kJ/kg calorific value

In a boiler, feed water supplied per hour is 205 kg while the coal fired per hour is 23 kg. Net enthalpy rise per kg of water is 115 KJ for conversion to steam. If the calorific valve of coal is 2050 KJ/kg, find the boiler efficiency.
  1. (a)75%
  2. (b)40%
  3. (c)50%
  4. (d)60%

Answer: (c) 50% Official final key: (c)

Boiler efficiency is the heat taken up by the water and steam divided by the heat released by the fuel.

, so , option (c).

Where this shows up in industry

Plant engineers track boiler efficiency the same way, from feed-water flow, steam enthalpy rise and fuel firing rate, in power stations and process-steam plants.

ISRO 2025 · Mechanical Set A · Q.12Part A · 1 mark · -0.33 if wrongThermodynamics and power cycles

Air standard Otto efficiency: 70 mm bore, 100 mm stroke, 42.78 cc clearance volume

Calculate the ideal air standard thermal efficiency based on Otto cycle for a petrol engine with a cylinder bore of 70 mm and stroke of 100 mm and clearance volume of ? Consider ratio of specific heats, , and .
  1. (a)40%
  2. (b)50%
  3. (c)30%
  4. (d)60%

Answer: (d) 60% Official final key: (d)

Swept volume: .

Compression ratio: .

Otto efficiency: . The given means .

, so , option (d). (Exactly, and .)

Where this shows up in industry

Compression ratio is the first lever engine designers use on efficiency; it is capped in petrol engines by knock, which is why direct-injection engines and higher-octane fuels allow higher ratios.

ISRO 2025 · Mechanical Set A · Q.13Part A · 1 mark · -0.33 if wrongThermodynamics and power cycles

Volume of 3 kg of wet steam at 1.3 bar with dryness fraction 0.8

Calculate the volume of 3 kg of steam at a pressure of 1.3 bar. The dryness fraction of the sample of steam is 0.8. The specific volume of water at 1.3 bar is and specific volume of dry stream is at 1.3 bar.
  1. (a)
  2. (b)
  3. (c)
  4. (d)

Answer: (b) Official final key: (b)

Specific volume of wet steam with dryness fraction : .

.

, so , option (b).

At this low pressure the liquid's volume is negligible, so the common approximation gives the same answer.

Where this shows up in industry

Wet-steam specific volume sets pipe and drum sizes in steam plants and the volume flow through the last stages of steam turbines, where moisture also erodes the blades.

ISRO 2025 · Mechanical Set A · Q.14Part A · 1 mark · -0.33 if wrongFluid mechanics and turbomachinery

Strength of a normal shock in air at Mach 2.0 with gamma 1.4

An air flow with Mach number 2.0 passes through a normal shock wave. If the ratio of specific heats of air is 1.4, find the shock strength.
  1. (a)2.5
  2. (b)3.5
  3. (c)1.5
  4. (d)4.5

Answer: (b) 3.5 Official final key: (b) · provisional key was (d)

Static pressure ratio across a normal shock:

.

Shock strength is defined as the pressure rise relative to the upstream pressure: , so shock strength , option (b).

Trap: option (d), 4.5, is the pressure ratio itself, not the strength.

ISRO's provisional key gave (d); the final key after objections is (b).

Where this shows up in industry

Normal-shock relations are used to size supersonic intakes, to correct Pitot readings on supersonic vehicles, and to predict where a shock sits inside an over-expanded rocket nozzle during ground tests.

ISRO 2025 · Mechanical Set A · Q.15Part A · 1 mark · -0.33 if wrongFluid mechanics and turbomachinery

Static pressure at the sonic point of isentropic flow with 6 MPa stagnation pressure

In an isentropic flow with a stagnation pressure of 6 MPa, find the static pressure, at the point where flow is sonic. (Assume ; consider )
  1. (a)2.17 MPa
  2. (b)3.17 MPa
  3. (c)1.58 MPa
  4. (d)2.58 MPa

Answer: (b) 3.17 MPa Official final key: (b)

Isentropic relation at Mach 1 (the critical pressure ratio):

With : . From the hint, , so .

, so , option (b). (Exactly, and .)

Where this shows up in industry

The critical pressure ratio of about 0.528 tells a nozzle designer when the throat chokes; rocket engines, gas generators and safety relief valves are all designed around this choked-flow condition.

ISRO 2025 · Mechanical Set A · Q.16Part A · 1 mark · -0.33 if wrongFluid mechanics and turbomachinery

Why specific impulse of a rocket engine increases in vacuum compared to sea level

Why specific impulse of a rocket engine increases in vacuum compared to sea level?
  1. (a)Combustion chamber pressure increases in vacuum
  2. (b)Mass flow rate of propellant decreases in vacuum
  3. (c)Exhaust velocity increases in vacuum
  4. (d)Mass flow rate of propellant increases in vacuum

Answer: (c) Exhaust velocity increases in vacuum Official final key: (c)

Rocket thrust has a momentum term and a pressure term:

Specific impulse is , where the effective exhaust velocity is .

In vacuum , so the pressure term is as large as it can be and rises. At sea level the same nozzle loses of thrust (and if the pressure term is negative). So (c) exhaust velocity increases in vacuum, read as the effective exhaust velocity, is the reason.

  • (a) False: chamber pressure is set by the propellant feed and the throat area; the choked throat isolates the chamber from ambient pressure.
  • (b) and (d) False: mass flow through a choked throat does not depend on ambient pressure at all.

Strictly, for a fixed nozzle flowing full, the gas velocity at the exit plane is fixed by the area ratio; what grows in vacuum is the effective exhaust velocity that includes the pressure thrust. Vacuum engines also use much larger area ratios to exploit this.

Where this shows up in industry

This is why upper-stage engines, such as the cryogenic upper stages of launch vehicles, carry long, high-area-ratio nozzles, and why every engine datasheet quotes separate sea-level and vacuum .

ISRO 2025 · Mechanical Set A · Q.17Part A · 1 mark · -0.33 if wrongEngineering mechanics

Exhaust velocity needed for a 10,000 kg rocket to gain 2 km/s in 50 s at 100 kg/s

A rocket with an initial mass of 10,000 kg ejects mass at a constant rate of 100 kg/s and at constant velocity through the nozzle. What should be the exit jet velocity, so as to increase the velocity of the rocket by 2 km/s in 50 seconds. [Assume no drag and optimal expansion in nozzle. Consider, ]
  1. (a)2886 m/s
  2. (b)3286 m/s
  3. (c)1000 m/s
  4. (d)1985 m/s

Answer: (a) 2886 m/s Official final key: (a)

With no drag (and no gravity loss) the velocity gain follows the Tsiolkovsky rocket equation:

Mass after 50 s: , so and .

, so , option (a).

The question intends a gravity-free burn. If a vertical climb against were included, the requirement would be , which is not among the options.

Where this shows up in industry

The rocket equation is the first sizing step for every launch vehicle stage: it ties the propellant mass fraction to the exhaust velocity the engine can deliver, which is why stages are dropped once empty.

ISRO 2025 · Mechanical Set A · Q.18Part A · 1 mark · -0.33 if wrongMaterials and manufacturing

Which material property cannot be significantly changed by heat treatment

Which of the following properties of material that cannot be significantly changed by heat treatment?
  1. (a)Ultimate tensile strength
  2. (b)Yield strength
  3. (c)Elastic Modulus
  4. (d)Ductility

Answer: (c) Elastic Modulus Official final key: (c)

Heat treatment (annealing, normalising, hardening, tempering, precipitation hardening) changes the microstructure: grain size, phases, precipitates and dislocation density. Properties that depend on how easily dislocations move change a lot.

  • (a) Ultimate tensile strength and (b) yield strength: change widely, for example a steel can roughly double in strength from annealed to quenched and tempered.
  • (d) Ductility: traded directly against strength by these same treatments.
  • (c) Elastic modulus: set by the stiffness of the interatomic bonds, which heat treatment does not alter. It changes by only a few per cent.

So the answer is (c) Elastic Modulus. It is called a structure-insensitive property for this reason.

Where this shows up in industry

Because modulus barely moves, a designer who needs a stiffer part must change the section or the material (for example steel to titanium or carbon fibre composite), not the heat treatment; heat treatment only buys strength.

ISRO 2025 · Mechanical Set A · Q.19Part A · 1 mark · -0.33 if wrongMaterials and manufacturing

Modulus of a composite with 60% fibre (200 GPa) and 40% matrix (5 GPa) by rule of mixtures

A composite material consists of 60% by volume of fibre (modulus 200 GPa) and 40% by volume of matrix (modulus 5 GPa). What is the approximate modulus of the composite (using rule of mixtures)?
  1. (a)122 GPa
  2. (b)82 GPa
  3. (c)42 GPa
  4. (d)22 GPa

Answer: (a) 122 GPa Official final key: (a)

The rule of mixtures (iso-strain, load along the fibres) weights each modulus by its volume fraction:

, so , option (a).

The fibres dominate the longitudinal stiffness. Across the fibres the inverse rule applies, , which gives only about , and that is why composite laminates are laid up in several directions.

Where this shows up in industry

The rule of mixtures is the first estimate used to size carbon fibre motor cases, payload adaptors and satellite structural panels before detailed laminate analysis.

ISRO 2025 · Mechanical Set A · Q.20Part A · 1 mark · -0.33 if wrongStrength of materials

Toughness with 300 MPa yield strength and 0.2 fracture strain, assuming linear elasticity

A material has a yield strength of 300 MPa and a fracture strain of 0.2. What is the approximate toughness (assuming linear elastic behaviour)?
  1. (a)60 MPa
  2. (b)30 MPa
  3. (c)600 MPa
  4. (d)300 MPa

Answer: (b) 30 MPa Official final key: (b)

Toughness is the energy absorbed per unit volume up to fracture, the area under the stress-strain curve.

With linear elastic behaviour up to fracture the curve is a straight line from the origin, so the area is a triangle:

(), option (b).

Trap: option (a), , is the rectangle you would use for a perfectly plastic material, not a linear elastic one.

Where this shows up in industry

Energy absorbed to fracture is what crash structures, pressure vessels and launch-vehicle separation hardware are designed around; real ductile metals absorb much more than this linear estimate because of plastic flow.

From ISRO prep to a core mechanical career

Talk to a counsellor.

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.

Talk to a career counsellor

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.