ISRO Scientist/Engineer Mechanical 2023 paper: Part A, questions 41 to 60, solved

Questions 41 to 60 of the ISRO Scientist/Engineer 'SC' Mechanical written test of 7 Jan 2024 (Set A): 20 questions, each solved by Skill-Lync. ISRO never published an answer key for this test, so every answer was worked out three times independently and the disagreements were settled before publishing.

Question paper published by ISRO's Centralised Recruitment Board; answers and solutions by Skill-Lync (no official key exists) · Updated 19 Nov 2026 · 20 of 95 questions on this page

ISRO 2023 · Mechanical Set A · Q.41Part A · 1 mark · -0.33 if wrongMaterials and manufacturing

Material removal rate when turning a 20 mm aluminium rod to 19 mm

A 20 mm diameter Aluminium rod is turned to 19 mm diameter in a single pass. If the axial speed of the tool is 200 mm/min and the spindle rotate at 600 rpm, the material removal rate is nearly
  1. (a)
  2. (b)
  3. (c)
  4. (d)

Answer: (a) Skill-Lync answer; ISRO published no key

In a single pass the tool removes a thin tube of metal. Its length along the axis grows at the axial (feed) speed, so the material removal rate is the cross-section area of that tube times the axial speed.

Depth of cut: . Cross-section area of the removed ring: .

The spindle speed of 600 rpm is not needed: it only fixes the feed per revolution () and the cutting speed, not the volume removed per minute.

Where this shows up in industry

Machinists and CAM programmers use MRR to size roughing passes against spindle power, for example when turning aluminium forgings for launch-vehicle structures.

ISRO 2023 · Mechanical Set A · Q.43Part A · 1 mark · -0.33 if wrongTheory of machines and vibrations

Mechanical advantage of a four bar mechanism with links 2 and 3 in line

The configuration of a planar four bar mechanism with frictionless joints is shown in the figure below. The length of the links are , , , and . The suffixes 1, 2, 3 and 4 represents the fixed, input, coupler and output link respectively. If and are the torque to the input and output link, what is the mechanical advantage of the mechanism?
180°2341
  1. (a)
  2. (b)
  3. (c)
  4. (d)

Answer: (c) Skill-Lync answer; ISRO published no key

With frictionless joints, the power in equals the power out: , so .

In the figure, links 2 and 3 are in one straight line ( between them) from the left fixed pivot to the top of link 4. The lengths , and form a 3-4-5 right triangle, so link 4 is perpendicular to the fixed link.

Find the instantaneous centre of links 2 and 4. It lies where the line through the two fixed pivots meets the line through the two moving joints. The line through the moving joints is the straight line formed by links 2 and 3, and it passes through the left fixed pivot, which is on the fixed link. So the centre sits at the left fixed pivot.

Its distance from the left pivot is zero, so and . (A direct velocity check agrees: the top of link 3 can only move at right angles to link 4, and with links 2 and 3 in line it comes out at zero speed.) The output link is momentarily at rest, a toggle position.

A tiny input torque can balance a very large output torque in this position.

Where this shows up in industry

Toggle positions are used deliberately in clamps, latches and press linkages, where a small input force gives a very large holding force.

ISRO 2023 · Mechanical Set A · Q.44Part A · 1 mark · -0.33 if wrongMachine design

Self-locking screw jack with square thread: friction angle and efficiency

What is true in respect of the self locking screw jack with square thread? (I) The friction angle is more than the helix angle of the thread. (II) The efficiency of the screw jack should not be more than 50%
  1. (a)Only I
  2. (b)Only II
  3. (c)Both I and II
  4. (d)None of the above

Answer: (c) Both I and II Skill-Lync answer; ISRO published no key

A screw jack is self-locking when the load cannot turn the screw back down on its own. That needs the friction angle to be at least the helix angle of the thread, . So statement (I) is correct: friction angle is more than the helix angle (equal is the limiting case).

For efficiency of a square thread, . At the self-locking limit :

If is larger than , the efficiency is lower still. So a self-locking screw jack always has an efficiency of at most 50%, and statement (II) is correct too.

Both statements are correct. (c) Both I and II

Where this shows up in industry

Self-locking lead screws hold a load without a brake in jacks, vices and test-rig actuators, at the cost of low efficiency and heat from friction.

ISRO 2023 · Mechanical Set A · Q.45Part A · 1 mark · -0.33 if wrongMaterials and manufacturing

Commonly used flux for brazing

The commonly used flux for brazing is:
  1. (a)Borax
  2. (b)Epoxy
  3. (c)
  4. (d)Inert gas

Answer: (a) Borax Skill-Lync answer; ISRO published no key

A brazing flux must clean the joint of oxide and keep it clean while the filler metal melts above . Borax, usually mixed with boric acid, melts near the brazing temperature and dissolves metal oxides, so it is the standard brazing flux.

Epoxy is a glue and not a flux. Ammonium chloride () is a classic flux for soft soldering at lower temperatures, which is the usual trap. An inert gas can replace flux in furnace brazing but is not itself a flux. (a) Borax

Where this shows up in industry

Borax-based fluxes are used when brazing copper, steel and nickel parts such as heat exchangers, injector and thruster hardware.

ISRO 2023 · Mechanical Set A · Q.46Part A · 1 mark · -0.33 if wrongThermodynamics and power cycles

Heat to remove to turn 1 kg of water at 30 C into ice at 0 C

For water, the latent heat of freezing is 334 kJ/kg and the specific heat capacity averages 4.19 kJ/kgK. The quantity of heat to be removed from 1 kg of water at 30C in order to turn it into ice at 0C is:
  1. (a)
  2. (b)
  3. (c)
  4. (d)

Answer: (d) Skill-Lync answer; ISRO published no key

Two things must be removed: the sensible heat to cool the water from to , then the latent heat to freeze it at .

The nearest option is (d), .

The trap is forgetting one of the two terms: cooling alone gives about 126 kJ and freezing alone 334 kJ. (d) 459 kJ

Where this shows up in industry

Ice-making plant, cold storage and cryogenic pre-cooling loads are sized by adding sensible and latent heat in just this way.

ISRO 2023 · Mechanical Set A · Q.47Part A · 1 mark · -0.33 if wrongStrength of materials

Effect of a point load applied at the shear centre of a beam

A point load applied at shear center of beam induces
  1. (a)Zero shear force
  2. (b)Zero bending
  3. (c)Pure twisting
  4. (d)Pure bending

Answer: (d) Pure bending Skill-Lync answer; ISRO published no key

The shear centre is the point in a section through which a transverse load must act for the beam to bend without twisting. A load applied there produces no torque about the beam axis.

So the options with twisting are out: (c) is wrong. A transverse point load does produce a shear force and a bending moment, so (a) and (b) are wrong too. What is left is bending without twist, which is option (d).

A caution on wording: strictly, "pure bending" means a constant moment with no shear, and a point load also causes shear. The question uses the phrase loosely for "bending only, no twisting", and (d) is the only option consistent with that meaning. (d) Pure bending

Where this shows up in industry

Open sections such as channels and Z-sections used in spacecraft and aircraft frames twist if loaded away from the shear centre, so attachments are placed through it.

ISRO 2023 · Mechanical Set A · Q.48Part A · 1 mark · -0.33 if wrongTheory of machines and vibrations

Natural frequency of a cantilever after it is broken into two halves

A cantilever beam of cross section A, moment of inertia I and length L is having natural frequency . If the beam is accidentally broken into two halves, the natural frequency of the remaining cantilever beam will be such that it
  1. (a)Increases
  2. (b)Decreases
  3. (c)Remains same
  4. (d)Cannot be obtained from the given data

Answer: (a) Increases Skill-Lync answer; ISRO published no key

For a uniform cantilever of length , the first natural frequency is

With the same section, : a shorter cantilever is stiffer (stiffness varies as ) and also lighter, so it vibrates faster.

After the break, the remaining cantilever has length :

The frequency rises to four times its original value. (a)

Where this shows up in industry

Shortening a cantilevered boom, antenna or probe raises its natural frequency sharply, which is why designers stiffen long appendages to stay clear of launch-vibration frequencies.

ISRO 2023 · Mechanical Set A · Q.49Part A · 1 mark · -0.33 if wrongThermodynamics and power cycles

Triple point of ammonia from two vapour pressure equations

Vapor pressure in mm of mercury of solid and liquid ammonia is given by and , find out the triple point.
  1. (a)700 K
  2. (b)231 K
  3. (c)200 K
  4. (d)180 K

Answer: (c) 200 K Skill-Lync answer; ISRO published no key

At the triple point the solid and the liquid have the same vapour pressure, so the two equations give the same at the same temperature.

At this temperature , so mm of Hg. (c) 200 K

Where this shows up in industry

Ammonia is a common refrigerant and spacecraft thermal-loop fluid; its triple point sets the lowest temperature at which it can circulate as a liquid.

ISRO 2023 · Mechanical Set A · Q.50Part A · 1 mark · -0.33 if wrongHeat transfer

Diameter of a 5 m aluminium ring dipped in liquid nitrogen

An aluminium ring of mean diameter of 5m at ambient temperature is dipped into a liquid nitrogen bath. What will be the mean diameter of ring in the LN bath. The coefficient of linear expansion of aluminium alloy in the temperature range may be taken as . (Ambient temperature may be taken as 24C. Boiling temperature of liquid nitrogen: 77 K).
  1. (a)4.978 m
  2. (b)4.958 m
  3. (c)5.138 m
  4. (d)4.865 m

Answer: (a) 4.978 m Skill-Lync answer; ISRO published no key

Every linear dimension of a body changes by the same fraction, so the mean diameter of a ring follows . The hole in a ring shrinks and grows just like the metal around it.

Convert the bath temperature: . Then .

The ring contracts by about 22 mm. Option (c) is what you get if you wrongly expand the ring. (a) 4.978 m

Where this shows up in industry

Cryogenic tanks and shrink-fit assemblies must allow for thermal contraction; LOX and LN2 hardware shrinks by several tenths of a per cent when chilled.

ISRO 2023 · Mechanical Set A · Q.51Part A · 1 mark · -0.33 if wrongEngineering mechanics

Counterweight and distance for a travelling crane with a 2 t load at D

A travelling crane as shown is used to carry a load of two tonnes at point D. A counter mass CW is to be added as shown to avoid toppling of the crane. Find the limiting value of counter mass and distance, X from F, such that it will not topple the crane even in the absence of load at D. The mass of the crane may be taken as 2 tonnes and is acting 2 meters away from E towards D.
CWFEDX6 m12 m30 mBC
  1. (a) at
  2. (b) at
  3. (c) at
  4. (d) at

Answer: (a) at Skill-Lync answer; ISRO published no key

The crane can topple two ways, so the counterweight at distance left of must satisfy two moment conditions. From the figure the legs stand at (under ) and (under ). Work in tonnes and metres.

1. Load of 2 t on at D: the crane must not tip forward about C. The load is and the crane weight beyond , and the counterweight is to the left of :

2. Load absent: the crane must not tip backward about B. The crane weight is right of , and the counterweight is left of :

The limiting case takes both as equalities. Subtracting gives , so , and then .

Check the options: (b) and (d) topple backward when unloaded. (c) topples forward under load. Only (a) satisfies both. (a) at

Where this shows up in industry

Tower and mobile crane design always checks stability for both the loaded and the unloaded case; the counterweight is sized between the two limits.

ISRO 2023 · Mechanical Set A · Q.52Part A · 1 mark · -0.33 if wrongEngineering mechanics

Speed of a car that skids 23 m on a level road with friction 0.5

In an accident site, tyre marks shows that a car was travelling along straight level street skidded for a total distance of 23 m, after the brakes applied. The coefficient of friction between the tyre and road estimated to be 0.5, what was the probable speed of car when break applied.
  1. (a)54 kmph
  2. (b)60.7 kmph
  3. (c)45.3 kmph
  4. (d)97 kmph

Answer: (a) 54 kmph Skill-Lync answer; ISRO published no key

On a level road the braking force is limited to friction, , so the deceleration is . The car stops after sliding a distance , so .

The speed was about 54 km/h when the brakes were applied. (a) 54 kmph

Where this shows up in industry

Accident reconstruction and vehicle-braking tests use this skid-distance relation to estimate impact speed.

ISRO 2023 · Mechanical Set A · Q.53Part A · 1 mark · -0.33 if wrongEngineering mechanics

Order of a sphere, solid cylinder and hollow cylinder rolling down an incline

If a solid cylinder, thin hollow cylinder and a sphere, all with same material and are having same outside diameter are allowed to roll down in same inclination without sliding. All surfaces are having same coefficient of friction. What is the order of the bodies reaching bottom
  1. (a)All reach together
  2. (b)Solid cylinder, sphere, thin hollow cylinder
  3. (c)Sphere, solid cylinder, thin hollow cylinder
  4. (d)Thin hollow cylinder, solid cylinder, sphere

Answer: (c) Sphere, solid cylinder, thin hollow cylinder Skill-Lync answer; ISRO published no key

For a body rolling without slipping down an incline of angle , energy gives

where is the radius of gyration. The mass and size cancel, so only the shape factor matters. The smaller it is, the larger the acceleration and the sooner the body reaches the bottom.

  • Solid sphere: , so
  • Solid cylinder: , so
  • Thin hollow cylinder: , so

The sphere is fastest, then the solid cylinder, then the thin hollow cylinder. The friction coefficient does not change the order as long as it is large enough to prevent sliding, which the question states. (c) Sphere, solid cylinder, thin hollow cylinder

Where this shows up in industry

The shape factor of rotating parts (wheels, flywheels, reaction wheels) decides how much of the energy goes into spin rather than motion along the track.

ISRO 2023 · Mechanical Set A · Q.54Part A · 1 mark · -0.33 if wrongFluid mechanics and turbomachinery

Maximum equipment mass on a floating cylinder in sea water

A cylindrical body of diameter 2 m and height 1.5 m having a mass of 2 tonnes and floats in sea water with its axis vertical. A lighting equipment is placed on the body such that the water level is at least 0.5 m below the top surface. What is the maximum mass of the electrical equipment that can be placed on the body. (The specific gravity of sea water may be taken as 1.02 and )
  1. (a)252 kg
  2. (b)750 kg
  3. (c)1202 kg
  4. (d)275 kg

Answer: (c) 1202 kg Skill-Lync answer; ISRO published no key

The body floats when its weight, including the equipment, equals the weight of water displaced. The most it can carry is when it sinks until the water level is below the top, which makes the draught .

Mass of water displaced, using and sea water density :

The maximum mass of the equipment is about 1203 kg, so the nearest option is (c). (c) 1202 kg (nearest option)

Where this shows up in industry

Buoy, pontoon and recovery-capsule flotation sizing starts with this displacement balance before checking stability.

ISRO 2023 · Mechanical Set A · Q.55Part A · 1 mark · -0.33 if wrongFluid mechanics and turbomachinery

Which statements on Euler, Bernoulli and Navier-Stokes equations are correct

Examine the following statements: (i) Euler's equation is applicable to inviscid liquid (ii) Bernoulli's equation applicable to steady state (iii) Viscous forces are not considered in Navier Stokes equation (iv) Surface tension and compressibility forces are considered in Navier Stokes equation
  1. (a)Statements (i) and (ii) are not correct
  2. (b)Statements (iii) and (iv) are correct
  3. (c)Statements (i), (ii) and (iii) are correct
  4. (d)All the statements are correct

Answer: (c) Statements (i), (ii) and (iii) are correct Skill-Lync answer; ISRO published no key

Judge each statement on its own.

  • (i) Euler's equation is the momentum equation for inviscid (frictionless) flow: correct.
  • (ii) Bernoulli's equation is derived for steady flow (along a streamline, inviscid, incompressible): correct.
  • (iii) The Navier-Stokes equations are the momentum equations that include viscous forces. Saying viscous forces are not considered is wrong.
  • (iv) In the usual Navier-Stokes equation the forces are pressure, viscous and body forces. Surface tension enters only through boundary conditions and compressibility is not included in the incompressible form: wrong as stated.

The fully correct reading is "(i) and (ii) only", and the paper does not offer that. (a) says (i) and (ii) are wrong, (b) says (iii) and (iv) are right, and (d) says all four are right: each contains at least two false claims. Option (c) contains two correct statements and only one false claim, (iii), so it is the closest to the true position. Treat this question as flawed: the working gives (i) and (ii) correct and (iii) and (iv) incorrect. (c) is the nearest option

Note on this question The correct working gives statements (i) and (ii) correct and (iii) and (iv) incorrect, a combination no option offers. Option (c) is the nearest, with only statement (iii) wrongly included, so the question is flawed as printed.

Where this shows up in industry

CFD codes solve the Navier-Stokes equations for viscous flow, while Euler solvers are used for fast inviscid estimates of launch-vehicle aerodynamics.

ISRO 2023 · Mechanical Set A · Q.56Part A · 1 mark · -0.33 if wrongHeat transfer

Heat flow through a wall after adding two low-conductivity layers

The wall of a chemical plant is modified with two additional layers having half the thermal conductivity of original wall material. The inner layer is of half the thickness and outer layer of same thickness as original wall. What will be the heat flow across the modified wall?
  1. (a)Same as original
  2. (b)Twice of original
  3. (c)50% of original
  4. (d)25% of original

Answer: (d) 25% of original Skill-Lync answer; ISRO published no key

The layers are in series, so thermal resistances add: for each layer. Take the original wall as thickness and conductivity , so . Assume the same overall temperature difference across the wall before and after.

  • Original wall:
  • Inner layer (thickness , conductivity ):
  • Outer layer (thickness , conductivity ):

Heat flow is , so it falls to one quarter: . (d) 25% of original

Where this shows up in industry

Multilayer insulation walls, furnace linings and thermal-protection stacks are analysed as resistances in series.

ISRO 2023 · Mechanical Set A · Q.57Part A · 1 mark · -0.33 if wrongStrength of materials

Order of increasing stress in three wires holding 2, 4 and 3 kg balls

Three metal balls are suspended by three wires (a, b & c) of equal length arranged in sequence as shown in figure. The masses of the balls, starting at the top, are 2 kg, 4kg and 3 kg. The wire diameters in the same order are 2 mm, 1.2 mm & 1 mm respectively. What is the correct order of increasing stresses in the wires?
abcA = 2 kgB = 4 kgC = 3 kg
  1. (a)a, c, b
  2. (b)b, c, a
  3. (c)a, b, c
  4. (d)All are having same stress

Answer: (a) a, c, b Skill-Lync answer; ISRO published no key

Each wire carries the weight of every ball hanging below it. Stress is force over cross-section area, and for round wires the area is proportional to , so (the factor is common and the wire's own weight is ignored).

  • Wire a (top, 2 mm) holds A, B and C: , so
  • Wire b (1.2 mm) holds B and C: , so
  • Wire c (1 mm) holds C: , so

Increasing order: wire a (2.25), wire c (3.00), wire b (4.86). The heavy middle ball and the thinner wire push wire b highest. (a) a, c, b

Where this shows up in industry

Tether, cable and suspension-wire sizing starts by finding the load each segment carries and dividing by its own area.

ISRO 2023 · Mechanical Set A · Q.58Part A · 1 mark · -0.33 if wrongStrength of materials

Strain energy in a rectangular cantilever with an end bending moment

The elastic strain energy stored in a rectangular cantilever beam due to a bending moment M applied at the end is given by ( is Maximum Bending Stress, V is Volume and E is Young's Modulus)
LbhM2
  1. (a)
  2. (b)
  3. (c)
  4. (d)

Answer: (c) Skill-Lync answer; ISRO published no key

A cantilever with an end moment has a constant bending moment along its length, so the strain energy is

For the rectangular section, and the extreme-fibre stress is

Substitute and :

With :

(c)

Where this shows up in industry

Strain-energy expressions give quick deflection and spring-rate estimates for flexure pivots, booms and mounting brackets.

ISRO 2023 · Mechanical Set A · Q.59Part A · 1 mark · -0.33 if wrongMachine design

Allowable stress amplitude by the Soderberg criterion for a reversed stress

A machine member is subjected to fluctuating stress, . The endurance limit of the material is 350 MPa and the yield strength is 500 MPa. If the factor of safety used in the design is 3.5, then the maximum allowable stress in MPa according to soderberg fatigue criteria is
  1. (a)10
  2. (b)200
  3. (c)100
  4. (d)50

Answer: (c) 100 Skill-Lync answer; ISRO published no key

The stress swings symmetrically about zero, so the mean stress is and the stress amplitude is (the frequency does not matter).

The Soderberg line with a factor of safety is

With , and :

The yield strength of 500 MPa drops out because there is no mean stress. (c) 100 MPa

Where this shows up in industry

Rotating shafts and vibrating brackets see fully reversed stress, and the fatigue limit with a safety factor sets the allowable amplitude.

ISRO 2023 · Mechanical Set A · Q.60Part A · 1 mark · -0.33 if wrongStrength of materials

Yield point of a plane stress element by the maximum shear stress theory

A plane stress element in a structural member under loading has , and , where . The yield strength of the material is 300 MPa. If the member is designed using the maximum shear stress theory, then the value of at which yielding starts is
  1. (a)60 MPa
  2. (b)75 MPa
  3. (c)100 MPa
  4. (d)120 MPa

Answer: (a) 60 MPa Skill-Lync answer; ISRO published no key

Principal stresses for the plane-stress element, in terms of :

So and . In plane stress the third principal stress is , and the largest difference is (not ).

Maximum shear stress theory: yielding starts when , that is :

Using only would wrongly give 75 MPa. (a) 60 MPa

Where this shows up in industry

Tresca and von Mises checks on pressure vessels and brackets use principal stresses, always including the zero out-of-plane stress.

From ISRO prep to a core mechanical career

Talk to a counsellor.

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.

Talk to a career counsellor

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.