ISRO Scientist/Engineer 'SC' Mechanical 2023 question paper, solved

ISRO's written test for Scientist/Engineer 'SC' (Mechanical) under its 2023 advertisement, held on 7 January 2024, question by question. ISRO has published the paper but never an answer key, so every answer here is Skill-Lync's own: computed by a checking script and solved twice more, blind, by separate solvers. Where a question is ambiguous or flawed, the solution says so.

Question paper published by ISRO's Centralised Recruitment Board; answers and solutions by Skill-Lync (no official key exists) · Updated 19 Nov 2026 · 20 of 95 questions on this page

How many questions were in the ISRO Scientist/Engineer Mechanical 2023 paper?

95 multiple-choice questions in two parts, written on 7 Jan 2024. Part A had 80 mechanical engineering questions of 1 mark each, with 0.33 deducted for a wrong answer. Part B had 15 aptitude questions worth 20 marks, with no negative marking. ISRO evaluated Part A out of 79 marks, so it dropped one question from evaluation without saying which, and it never published an answer key for this test: the answers below are Skill-Lync's, each worked out three times independently.

Which subjects carried the most marks?

Counting the 80 Part A questions by subject: strength of materials 13, machine design 13, materials and manufacturing 11. Together that is 37 of 80 technical marks. The remaining questions spread over 7 more subjects; the table below links every question.

What was the cut-off for this paper?

ISRO evaluated the Mechanical paper out of 99 (79 + 20). Candidates other than PwBD needed at least 39.5 in Part A and 10 in Part B (half of each part; 40% for PwBD), and the last candidate short-listed for interview, other than PwBD, scored 55.04 (PwBD 44.00). After a corrected evaluation of Part B, ISRO re-issued the results on 30 May 2024 with 1,086 candidates short-listed for 163 posts. The selection panel named 153 plus 3 PwBD with 153 on the wait list; the last selected candidate's final score (written test and interview, 50% each) was 67.20 out of 100, and ISRO operated the wait list up to number 53 before the panel lapsed on 12 Dec 2025.

Questions by subject, ISRO Mechanical 2023 (Set A), counted by Skill-Lync
SubjectQuestionsQuestion numbers
Strength of materials13562434354757586069737778
Machine design1310121321394044596170747576
Materials and manufacturing1178111415313637414562
Engineering mechanics9305152536364666768
Thermodynamics and power cycles82342628294649
Theory of machines and vibrations82223384243486572
Metrology, CNC and industrial engineering79161718192071
Fluid mechanics and turbomachinery727323354557980
Refrigeration, air conditioning and psychrometrics2125
Heat transfer25056
Aptitude: reasoning and verbal1081828384858687899091
Aptitude: quantitative58892939495

ISRO 2023 · Mechanical Set A · Q.1Part A · 1 mark · -0.33 if wrongRefrigeration, air conditioning and psychrometrics

Power of a 2 tonne refrigeration system (latent heat 336 kJ/kg)

What is the power of 2 tonne refrigeration system? Latent heat of ice may be taken as 336 kJ/kg and specific heat capacity of water as 4 kJ/kgK.
  1. (a)7.7 kW
  2. (b)70 kW
  3. (c)12.5 kW
  4. (d)0.7 kW

Answer: (a) 7.7 kW Skill-Lync answer; ISRO published no key

One tonne of refrigeration is the cooling needed to freeze (or melt) one tonne of ice in 24 hours. The question gives no water temperature, so the water is taken as already at and only the latent heat counts. The specific heat of water is not needed.

, closest to option (a),

Sense check: , so , which rules out , and .

Where this shows up in industry

Refrigeration plant, cold-chain and chiller capacities are quoted in tonnes of refrigeration; test-stand cryo and ground-support cooling units are sized the same way.

ISRO 2023 · Mechanical Set A · Q.2Part A · 1 mark · -0.33 if wrongThermodynamics and power cycles

Air standard Otto cycle efficiency, r = 9, adiabatic index 1.5

An air standard Otto cycle operates with a compression ratio of 9 and the ambient temperature is 300 K. If the adiabatic index of the medium is 1.5, what is the efficiency?
  1. (a)75 %
  2. (b)66.67 %
  3. (c)50 %
  4. (d)33 %

Answer: (b) 66.67 % Skill-Lync answer; ISRO published no key

Otto efficiency depends only on the compression ratio and the index , not on the ambient temperature.

The is a distractor. With the usual the answer would be about , so using the given matters.

Where this shows up in industry

Spark-ignition engine design: compression ratio sets the ideal efficiency ceiling, which is then cut by real-gas, heat-loss and knock limits.

ISRO 2023 · Mechanical Set A · Q.3Part A · 1 mark · -0.33 if wrongThermodynamics and power cycles

Mollier diagram is also called which chart

Molliar diagram is also called as
  1. (a)Temperature – entropy chart
  2. (b)Pressure – volume chart
  3. (c)Pressure – enthalpy chart
  4. (d)Enthalpy – entropy chart

Answer: (d) Enthalpy – entropy chart Skill-Lync answer; ISRO published no key

The Mollier diagram, as defined in thermodynamics, plots specific enthalpy against specific entropy . Steam turbine expansion is read off it as a vertical line (isentropic) between pressure lines.

Enthalpy – entropy chart

Caveat: refrigeration texts also call the pressure-enthalpy chart a Mollier chart, so option (c) can be argued. The standard definition, and the better answer here, is the - chart.

Note on this question The standard definition of the Mollier diagram is the enthalpy-entropy chart, so (d) is chosen. Refrigeration textbooks also call the pressure-enthalpy chart a Mollier chart, so (c) could be defended.

Where this shows up in industry

Steam-turbine and nozzle expansion work is done on the h-s chart; refrigeration cycles are usually drawn on the p-h chart.

ISRO 2023 · Mechanical Set A · Q.4Part A · 1 mark · -0.33 if wrongThermodynamics and power cycles

When real gas behaviour approaches the ideal gas equation

Real gas behavior approaches ideal gas equation when
  1. (a)Pressure and temperature are very high
  2. (b)Pressure is very high and temperature is very low
  3. (c)Pressure and temperature are very low
  4. (d)Pressure is very low and temperature is very high

Answer: (d) Pressure is very low and temperature is very high Skill-Lync answer; ISRO published no key

A real gas behaves ideally when molecules are far apart (so their volume is negligible) and move fast (so intermolecular attraction is negligible). That needs low pressure and high temperature, i.e. compressibility factor .

High pressure squeezes molecules together; low temperature lets attraction dominate. Options (a), (b) and (c) each break at least one condition.

Low pressure and high temperature

Where this shows up in industry

Ideal-gas models are used for air and propellant gases at low density; cryogenic and high-pressure tanks need real-gas equations of state.

ISRO 2023 · Mechanical Set A · Q.5Part A · 1 mark · -0.33 if wrongStrength of materials

Thermal stress in a freely heated 12 mm steel rod on a frictionless surface

A stainless steel rod of diameter 12 mm and length 2.5 m is kept on frictionless surface and heated from 300 K to 400 K. What is the thermal stress on the rod? (coefficient of linear expansion of the steel may be taken as /K; yield strength of steel as 200 MPa and Young's modulus as 210 GPa)
  1. (a)52.5 MPa
  2. (b)0.525 MPa
  3. (c)1 MPa
  4. (d)0 MPa

Answer: (d) 0 MPa Skill-Lync answer; ISRO published no key

Thermal stress appears only when expansion is prevented. The rod lies on a frictionless surface with nothing holding its ends, so it is free to lengthen.

The rod simply grows by with nothing resisting the growth, so the stress is zero.

Trap: if both ends were rigidly held, , which would exceed the yield.

Where this shows up in industry

Expansion joints, sliding supports and floating bearings are provided exactly so that heated members can grow freely without thermal stress.

ISRO 2023 · Mechanical Set A · Q.6Part A · 1 mark · -0.33 if wrongStrength of materials

Radius of the Mohr circle of stress equals which quantity

Radius of the Mohr circle of stress numerically equal to
  1. (a)Maximum normal stress
  2. (b)Maximum shear stress
  3. (c)Average normal stress
  4. (d)Average shear stress

Answer: (b) Maximum shear stress Skill-Lync answer; ISRO published no key

The Mohr circle is centred at the average normal stress on the axis. Its radius is

The top of the circle is the largest shear stress, so the radius equals it. The maximum normal stress is , and the average normal stress is the centre.

Maximum shear stress

Where this shows up in industry

Stress transformation with Mohr's circle is used to find principal stresses and maximum shear in pressure vessels and shafts.

ISRO 2023 · Mechanical Set A · Q.7Part A · 1 mark · -0.33 if wrongMaterials and manufacturing

Name of the horizontal channel from pouring basin to mould cavity

In a casting process, a horizontal channel through which molten metal flows from pouring basin to reach mold cavity is called
  1. (a)Runner
  2. (b)Thinner
  3. (c)Corridor
  4. (d)Raiser

Answer: (a) Runner Skill-Lync answer; ISRO published no key

In a gating system, metal enters the pouring basin, drops through the vertical sprue, and then travels along the horizontal runner, which feeds the gates and the mould cavity.

"Thinner" and "corridor" are not gating terms, and a riser (spelt "raiser" here) is a reservoir that feeds shrinkage, not a flow channel.

Runner

Where this shows up in industry

Gating and runner design in aluminium and steel castings controls turbulence and oxide defects in engine and structural parts.

ISRO 2023 · Mechanical Set A · Q.8Part A · 1 mark · -0.33 if wrongMaterials and manufacturing

Which of these are 3D printing techniques

3D Printing Techniques are
  1. (a)Selective laser sintering
  2. (b)Selective laser melting
  3. (c)Electron beam melting
  4. (d)All the Above

Answer: (d) All the Above Skill-Lync answer; ISRO published no key

All three are powder-bed additive manufacturing processes:

  • Selective laser sintering fuses polymer or metal powder with a laser without fully melting it.
  • Selective laser melting fully melts metal powder with a laser.
  • Electron beam melting melts metal powder with an electron beam in vacuum.

All the above

Where this shows up in industry

Metal powder-bed printing is used for rocket engine injectors and brackets, where complex internal passages cut part count and mass.

ISRO 2023 · Mechanical Set A · Q.9Part A · 1 mark · -0.33 if wrongMetrology, CNC and industrial engineering

Name of the revolving joint of a robot

What is the revolving joint of the robot called?
  1. (a)V-Joint
  2. (b)L-Joint
  3. (c)O-Joint
  4. (d)T-Joint

Answer: (a) V-Joint Skill-Lync answer; ISRO published no key

Robot joints are coded by letter: L is a linear (sliding) joint, O is an orthogonal linear joint, R is a rotational joint, T is a twisting joint and V is a revolving joint.

In a revolving joint the input link is parallel to the axis of rotation and the output link is perpendicular to it. That is the V-joint.

V-Joint

Where this shows up in industry

Joint notation such as L, R, T and V is used to describe and compare robot arm configurations in manufacturing automation.

ISRO 2023 · Mechanical Set A · Q.10Part A · 1 mark · -0.33 if wrongMachine design

Identifying Soderberg, Goodman and Gerber lines on a fatigue diagram

The diagram below is showing the various criteria of fatigue failure. Which option is the correct representation of these criteria? (Subscripts e, y and u represent endurance, yield and ultimate respectively.)
σe0σyσm321Mean stress (σm)Variable stress (σv)
  1. (a)1 - Soderberg line, 2 - Goodman line, 3 - Gerber line
  2. (b)1 - Goodman line, 2 - Soderberg line, 3 - Gerber line
  3. (c)1 - Soderberg line, 2 - Gerber line, 3 - Goodman line
  4. (d)1 - Gerber line, 2 - Soderberg line, 3 - Goodman line

Answer: (a) 1 - Soderberg line, 2 - Goodman line, 3 - Gerber line Skill-Lync answer; ISRO published no key

All criteria start at the endurance limit on the vertical axis. They differ in where they meet the mean-stress axis and in shape.

  • Soderberg: a straight line to the yield strength . It ends earliest, so it is the steepest and most conservative. That is line 1.
  • Goodman: a straight line to the ultimate strength . That is line 2.
  • Gerber: a parabola to , bulging above the Goodman line. That is curve 3.

1 - Soderberg, 2 - Goodman, 3 - Gerber

Where this shows up in industry

Shafts, springs and engine components under fluctuating loads are checked against Goodman or Soderberg lines to set a safety factor against fatigue.

ISRO 2023 · Mechanical Set A · Q.11Part A · 1 mark · -0.33 if wrongMaterials and manufacturing

Definition of specific stiffness of a material

The specific stiffness of a material is defined as the ratio of
  1. (a)Mass to Young's modulus
  2. (b)Density to Young's modulus
  3. (c)Young's modulus to Density
  4. (d)Young's modulus to Mass

Answer: (c) Young's modulus to Density Skill-Lync answer; ISRO published no key

Specific stiffness is stiffness per unit weight of material:

It is high for materials like aluminium, titanium and CFRP that are stiff for little mass. Option (b) is the inverse ratio.

Young's modulus to density

Where this shows up in industry

Launch vehicle and satellite structures are chosen on specific stiffness to get a stiff frame at the lowest mass.

ISRO 2023 · Mechanical Set A · Q.12Part A · 1 mark · -0.33 if wrongMachine design

Gear type for non-parallel, non-intersecting shafts

The type of gear used to transmit rotary motion between non-parallel and non-intersecting shaft is
  1. (a)Spur gear
  2. (b)Helical gear
  3. (c)Bevel gear
  4. (d)Worm gear

Answer: (d) Worm gear Skill-Lync answer; ISRO published no key

Match the gear to the shaft layout:

  • Spur and (normally mounted) helical gears: parallel shafts.
  • Bevel gears: intersecting shafts.
  • Worm and worm wheel: shafts at right angles that do not intersect (skew shafts).

Worm gear

Where this shows up in industry

Worm drives give high single-stage reduction with a right-angle layout, as in actuator gearboxes and steering mechanisms.

ISRO 2023 · Mechanical Set A · Q.13Part A · 1 mark · -0.33 if wrongMachine design

Bearing not suitable for axial thrust load

Which of the bearings given below is not suitable for axial thrust load?
  1. (a)Deep groove ball bearing
  2. (b)Angular contact ball bearing
  3. (c)Single row tapered bearing
  4. (d)Straight Cylindrical roller bearing

Answer: (d) Straight Cylindrical roller bearing Skill-Lync answer; ISRO published no key

A straight cylindrical roller bearing has line contact parallel to the shaft axis, so it carries heavy radial load but essentially no axial thrust.

Deep groove ball bearings take moderate axial load in both directions. Angular contact and tapered roller bearings are designed for combined radial and axial load.

Straight cylindrical roller bearing

Where this shows up in industry

Gearbox shafts pair a thrust-capable bearing (tapered or angular contact) with a cylindrical roller bearing that handles radial load only.

ISRO 2023 · Mechanical Set A · Q.14Part A · 1 mark · -0.33 if wrongMaterials and manufacturing

Which of these is not a casting defect

Which of the following is not a casting defect?
  1. (a)Spatter
  2. (b)Blow holes
  3. (c)Cold shut
  4. (d)Hot tear

Answer: (a) Spatter Skill-Lync answer; ISRO published no key

Blow holes (trapped gas), cold shut (two metal streams failing to fuse) and hot tear (cracking while the casting is still hot) are all casting defects.

Spatter is the small droplets of molten metal thrown out around a welding arc. It is a welding defect.

Spatter

Where this shows up in industry

Casting inspection (radiography, dye penetrant) looks for blow holes, cold shuts and hot tears in structural castings.

ISRO 2023 · Mechanical Set A · Q.15Part A · 1 mark · -0.33 if wrongMaterials and manufacturing

What improves weldability of steel

Which of the following improve weld ability of steel?
  1. (a)Low carbon content and poor affinity to oxygen
  2. (b)High carbon content and poor affinity to oxygen
  3. (c)Low carbon content and good affinity to oxygen
  4. (d)High carbon content and good affinity to oxygen

Answer: (a) Low carbon content and poor affinity to oxygen Skill-Lync answer; ISRO published no key

Carbon content: high carbon steel forms hard, brittle martensite in the heat-affected zone and cracks, so weldability improves with low carbon.

Oxygen affinity: a metal that reacts strongly with oxygen forms oxide films and inclusions in the weld pool, so poor affinity for oxygen helps.

Low carbon content and poor affinity to oxygen

Where this shows up in industry

Structural and pressure-vessel steels are chosen with low carbon equivalent so they can be welded without preheat or cracking.

ISRO 2023 · Mechanical Set A · Q.16Part A · 1 mark · -0.33 if wrongMetrology, CNC and industrial engineering

Table feed in face milling with 4 teeth at 300 rpm

A face milling operation is carried out with a 100 mm diameter milling cutter having 4 teeth and spindle speed of 300 rpm. If the feed per tooth is 0.125 mm, what is the table feed in mm/min?
  1. (a)90 mm/min
  2. (b)120 mm/min
  3. (c)150 mm/min
  4. (d)180 mm/min

Answer: (c) 150 mm/min Skill-Lync answer; ISRO published no key

Table feed is feed per tooth times number of teeth times spindle speed.

The cutter diameter is not needed.

Where this shows up in industry

Feed-rate setting in CNC face milling of flat surfaces on aluminium and steel parts.

ISRO 2023 · Mechanical Set A · Q.17Part A · 1 mark · -0.33 if wrongMetrology, CNC and industrial engineering

Correct sequence to finish a large through hole

Which is the correct sequence of machining operations to be performed to finish a through hole of large diameter?
  1. (a)Drilling, reaming, boring
  2. (b)Drilling, boring, reaming
  3. (c)Boring, drilling, reaming
  4. (d)Boring, reaming, drilling

Answer: (b) Drilling, boring, reaming Skill-Lync answer; ISRO published no key

Drilling makes the rough hole first. Boring then enlarges it to near size and corrects its position and straightness. Reaming goes last to give a precise size and a fine surface finish.

Boring cannot come before drilling, since boring needs an existing hole, and reaming only removes a tiny allowance so it must be the last step.

Drilling, boring, reaming

Where this shows up in industry

Bearing bores in housings and engine blocks are produced by this drill, bore, ream sequence.

ISRO 2023 · Mechanical Set A · Q.18Part A · 1 mark · -0.33 if wrongMetrology, CNC and industrial engineering

Material removal mechanism in abrasive jet machining

In abrasive jet machining process, the main mechanism of material removal takes place due to?
  1. (a)Electrochemical action
  2. (b)Ionic dissolution
  3. (c)Mechanical impact
  4. (d)Melting and evaporation

Answer: (c) Mechanical impact Skill-Lync answer; ISRO published no key

In abrasive jet machining a high-speed gas jet carries fine abrasive grains that strike the work. Each grain chips away tiny fragments by erosion, a purely mechanical impact.

Electrochemical action and ionic dissolution belong to ECM, and melting and evaporation to EDM, laser or electron-beam machining.

Mechanical impact

Where this shows up in industry

Abrasive jets are used to deburr and clean hard, brittle or heat-sensitive parts such as glass, ceramics and thin sections.

ISRO 2023 · Mechanical Set A · Q.19Part A · 1 mark · -0.33 if wrongMetrology, CNC and industrial engineering

Monthly profit at 75% of rated capacity

A manufacturer has the following data regarding a product. Fixed cost per month = Rs. 80,000; Variable cost per unit = Rs. 350; Selling price per unit = Rs. 500; Production capacity = 1600 units per month. If the production is carried out at 75% of the rated capacity, then monthly profit is (in Rs.)
  1. (a)1 Lakh
  2. (b)1.2 Lakhs
  3. (c)1.4 Lakhs
  4. (d)0.8 Lakhs

Answer: (a) 1 Lakh Skill-Lync answer; ISRO published no key

Output at 75%: units.

Contribution per unit .

Profit (1 lakh)

Where this shows up in industry

Break-even and contribution analysis decides production volume and pricing in manufacturing plants.

ISRO 2023 · Mechanical Set A · Q.20Part A · 1 mark · -0.33 if wrongMetrology, CNC and industrial engineering

PERT expected activity time in seconds

For a PERT activity, the optimistic time is 6 minutes, the most likely time is 9 minutes and pessimistic time is 16 minutes. The expected time of the activity (in seconds) is
  1. (a)600
  2. (b)540
  3. (c)620
  4. (d)580

Answer: (d) 580 Skill-Lync answer; ISRO published no key

PERT uses the beta-distribution estimate.

. Convert to seconds: .

Where this shows up in industry

PERT is used to schedule launch campaigns and assembly programmes where task durations are uncertain.

From ISRO prep to a core mechanical career

Talk to a counsellor.

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.

Talk to a career counsellor

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.