GATE Electronics (EC): Electromagnetics (Maxwell's equations, plane waves and polarisation, transmission lines and Smith chart, waveguides and antennas), previous-year questions solved

Every electromagnetics question from the last five GATE Electronics and Communication papers, solved: charges, currents and induction, plane waves and their polarisation, transmission lines with reflection, standing waves and the Smith chart, S-parameters, waveguides and the Friis link equation. Each answer matches the official key and was recomputed by code: a numeric integral over the charge, the field vector traced over one period, the line voltage sampled along its length, or the waveguide modes enumerated one by one.

Questions from official GATE EC papers (IIT Kharagpur 2022, IIT Kanpur 2023, IISc Bengaluru 2024, IIT Roorkee 2025, IIT Guwahati 2026); solutions by Skill-Lync. · Updated 17 Nov 2026 · 7 of 22 questions on this page

GATE 2022 · EC · Q.24MCQ · 1 markElectrostatics, currents and Maxwell's equations

Conduction current 2sin(t + pi/2) A in a series resistor: displacement current in the capacitor

In a circuit, there is a series connection of an ideal resistor and an ideal capacitor. The conduction current (in Amperes) through the resistor is . The displacement current (in Amperes) through the capacitor is _________.
  1. (A)
  2. (B)
  3. (C)
  4. (D)

Answer: (C) Official key: C

  1. In a series connection the same current flows through every element. The current in the resistor, , is the current in the wires that feed the two capacitor plates.
  2. Inside an ideal capacitor there are no free charges moving across the dielectric, so there is no conduction current between the plates. The current is continued by the displacement current .
  3. Total current is continuous: whatever charge arrives at one plate per second changes the flux of between the plates at the same rate. For a plate of area with uniform field , the displacement current is .
  4. And is exactly the current that flows into the capacitor, which is . So .
  5. Check with the waveforms: , and .
  6. The displacement current is , option (C).

Trap: the two phase-shifted options come from putting the wrong quantity in the current's place. Option (A), , is the waveform of the capacitor voltage (take ), that is, the integral of the current. Option (B), , is the time derivative of the current, . Neither is the displacement current. The code integrated the given current into (trapezoid rule, points over to s), took numerically for a parallel-plate capacitor, and compared it with each option. The largest difference was A for option (C), against A for (A), A for (B) and A for (D). It also confirmed that option (A) equals (difference ) and option (B) equals (difference ).

Where this shows up in industry

A decoupling capacitor on a power rail passes the supply's ripple current even though no charge crosses its dielectric: the displacement current between the plates carries it. The same idea lets circuit theory say that current is continuous around a loop that contains a capacitor, and it is the term Maxwell added to Ampere's law.

GATE 2022 · EC · Q.65NAT · 2 marksElectrostatics, currents and Maxwell's equations

Charge inside a 1 m cube centred at the origin for D = x^3 i + y^3 j + x y^2 k C/m^2

In an electrostatic field, the electric displacement density vector, , is given bywhere , , are the unit vectors along -axis, -axis, and -axis, respectively. Consider a cubical region centered at the origin with each side of length , and vertices at . The electric charge enclosed within is _________ C (rounded off to two decimal places).

Answer: Official key: 0.48 to 0.52

  1. Gauss's law in differential form: . The charge in is .
  2. Divergence: .
  3. , and the other two sides of the cube have length .
  4. .
  5. Flux check: on the faces the outward flux is per on each, total . The faces give another . On the faces , is the same on both but the outward normals are opposite, so they cancel. Total .

Trap: the answer is easy to halve to by integrating only and forgetting the term (or by counting the flux through one pair of faces). The code took the divergence in sympy (exactly ) and integrated it over the cube: . It then computed the outward flux of through the six faces numerically on an midpoint grid per face: faces C, faces C, faces C, total C. A third check, the volume integral of on a grid, gave C. Dropping the term gives C, outside the official range to .

Where this shows up in industry

Field solvers used for capacitance extraction and for high-voltage insulation design find the charge on an electrode exactly this way: they integrate over a closed surface around it, and then divide by the voltage to get capacitance. The same flux integral is used in hand checks of a solver's mesh.

GATE 2024 · EC · Q.16MCQ · 1 markElectrostatics, currents and Maxwell's equations

Fields F1 = A(y i + x j) and F2 = A(y i - x j): which is an electrostatic field

Let and be the unit vectors along and axes, respectively and let be a positive constant. Which one of the following statements is true for the vector fields and ?
  1. (A)Both and are electrostatic fields.
  2. (B)Only is an electrostatic field.
  3. (C)Only is an electrostatic field.
  4. (D)Neither nor is an electrostatic field.

Answer: (B) Official key: B

  1. A static electric field satisfies Faraday's law with no time variation, . It is curl-free, so its line integral around any closed path is zero (). A field must pass this test to be electrostatic.
  2. For a field in the plane, .
  3. : . Curl-free, and .
  4. : . Not curl-free.
  5. Only is electrostatic: option (B).

Trap: option (A) or (C) comes from checking the divergence instead of the curl. Both fields have (sympy gave and ), so both could be charge-free fields, but that says nothing about being electrostatic. The code computed the curl in sympy (-component for and for ), then integrated numerically around a circle of radius and a square of side (with ): gave and , gave and , which is ( and ) for the anticlockwise path. Testing all four options against these results leaves only (B).

Where this shows up in industry

Field solvers for electrostatics (insulator and electrode design) rely on this: a static field is , so it can be described by a scalar potential and its closed-loop integral is zero. A field with non-zero curl, like , cannot come from fixed charges and would need a changing magnetic flux.

GATE 2025 · EC · Q.49MCQ · 2 marksElectrostatics, currents and Maxwell's equations

Total charge on a 4 m x 4 m sheet centred on the origin with surface charge density 4|y| uC/m^2

A square metal sheet of is placed on the x-y plane as shown in the figure below.
If the surface charge density (in ) on the sheet is , then the total charge (in , rounded off to the nearest integer) on the sheet is ________.
A square metal sheet in the x-y plane with corners at (-2, 2), (2, 2), (-2, -2) and (2, -2) metres, centred on the origin, with x and y axes in metresy (m)x (m)(-2, 2)(2, 2)(-2, -2)(2, -2)
  1. (A)16
  2. (B)85
  3. (C)64
  4. (D)256

Answer: (C) Official key: C

  1. Total charge from a surface density: over the sheet. The sheet is and (metres), from the corner coordinates in the figure.
  2. is even in , so the upper and lower halves hold equal charge. Do not let the integral run straight from to without the modulus: alone would cancel to zero.
  3. .
  4. , so , option (C).

Trap: dropping the modulus gives , so ; reading as gives , which rounds to , option (B). The code summed over a grid on the sheet (midpoint rule) and got , matching the exact sympy integral . Only (C) matches. The upper half alone holds .

Where this shows up in industry

Integrating a non-uniform surface charge density over a plate is how the charge on a touch-screen electrode, a MEMS comb plate or an electrostatic-discharge pad is estimated from a field-solver map. The same sum of density times area is what a charge-density plot in a field simulator reports as total charge.

GATE 2025 · EC · Q.50MCQ · 2 marksElectrostatics, currents and Maxwell's equations

Current in a 1 mm diameter copper wire (sigma = 5.8e7 S/m) with 0.01 V/m applied along its length

An electric field of is applied along the length of a copper wire of circular cross-section with diameter . Copper has a conductivity of .
The current (in Amperes, rounded off to two decimal places) flowing through the wire is _________.
  1. (A)0.46
  2. (B)1.82
  3. (C)0.58
  4. (D)1.12

Answer: (A) Official key: A

  1. Ohm's law at a point: .
  2. The field is along the wire, so the current density is uniform over the cross-section and .
  3. Diameter mm means radius , so .
  4. , option (A).

Trap: using the diameter as the radius makes the area four times too big, A, option (B); using a square section gives A, option (C). The code integrated over the circular section in polar coordinates (, midpoint rule, rings) and with sympy, both A, and tested the four options against the rounded value: only (A) matches.

Where this shows up in industry

Current density in a copper conductor is the number that sets wire and PCB trace sizing: here J is about 0.58 A/mm^2, far below the several A/mm^2 where heating becomes the limit. The relation J = sigma E is the starting point for the DC resistance of a trace, R = L / (sigma A), that a layout tool reports.

GATE 2025 · EC · Q.65NAT · 2 marksElectrostatics, currents and Maxwell's equations

Current in a 5 m^2 loop with two 2 ohm resistors when B(t) = 0.5t tesla is applied along +z

Two resistors are connected in a circuit loop of area , as shown in the figure below. The circuit loop is placed on the x-y plane.
When a time-varying magnetic flux, with flux-density (in Tesla), is applied along the positive z-axis, the magnitude of current (in Amperes, rounded off to two decimal places) in the loop is ________.
A rectangular loop in the x-y plane with a 2 ohm resistor in its left side and a 2 ohm resistor in its right side, current I marked leftward on the top side, the enclosed region labelled Loop Area, and x, y and z axes beside it2 Ω2 ΩILoop Areayxz

Answer: Official key: 0.62 to 0.63

  1. Faraday's law: the induced emf is the rate of change of flux through the loop, .
  2. The field is along and the loop lies in the x-y plane, so the flux is .
  3. , constant in time.
  4. The two resistors sit in the same single loop, so they are in series and carry the same current: .
  5. (the key accepts to ).

Trap: using only one resistor gives A, and treating the two as parallel () gives A, both outside the key range. Both resistors are in one loop, so they carry the same current and add. The code differentiated the flux with sympy ( V), repeated it as a finite difference of the flux over ms ( A) and tested the two wrong paths against the key range.

Where this shows up in industry

This is the induced-voltage picture behind current probes, Rogowski coils and the loop pickup of switching noise on a PCB: an emf of area times dB/dt appears in any loop, and the loop resistance sets the current. Keeping the loop area small, for example by routing a signal close to its return path, is the standard layout fix.

GATE 2026 · EC · Q.28MSQ · 1 markElectrostatics, currents and Maxwell's equations

Which options represent the dielectric loss tangent of a substrate (displacement current, susceptibility, P and D)

Which option(s) represents/ represent the dielectric loss tangent of a substrate?
  1. (A)Ratio of the real to imaginary parts of the total displacement current
  2. (B)
  3. (C)Ratio of the electric susceptibility to permittivity
  4. (D)Ratio of the polarization vector to the displacement vector

Answer: (A) and (B) Official key: A;B

  1. A lossy substrate has complex permittivity and conductivity . With the time factor , the total current density driven by is .
  2. Expand it: .
  3. The real (in-phase) part is the loss current. The imaginary (quadrature) part is the ideal capacitive displacement current.
  4. The loss tangent is the ratio of the two: . So (A) and (B) are the same statement and both are correct.
  5. (C) and (D) are made of real, lossless quantities. and would not become zero for a perfect insulator, while the loss tangent does. So (C) and (D) are wrong.

Trap: it is tempting to tick (C) or (D) because susceptibility and also describe how a dielectric responds to a field. They describe polarisation strength, not loss. The code built the complex current for a substrate with , and at , found real over imaginary equal to the closed form in (B) and to dissipated power over reactive power from the time waveforms (), then repeated it for an ideal lossless dielectric: the true loss tangent is there, while and stay non-zero. Only (A) and (B) pass both tests.

Where this shows up in industry

PCB laminate datasheets quote the loss tangent (about 0.02 for ordinary FR-4 and a few thousandths for RF laminates) because it sets how much of a signal is turned into heat in the board: dielectric loss in dB per inch grows in proportion to frequency times tan delta. RF designers choose the laminate by this number once traces carry gigahertz signals.

From GATE prep to a hardware design career

Talk to a counsellor.

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.

Talk to a career counsellor

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.