Car roof design calculator: roof bow spacing, heat distortion W, snow load Qr and FMVSS 216a roof crush

In the roof design challenge, each panel zone between two members needs a heat distortion index W below 2.7, and each bow needs a snow load index Qr of at least 3.1 with s = L1/2 + L2/2 between 250 and 380 mm. A roof about 2,020 mm long meets that s window only with 5 to 7 evenly spaced bows. For roof crush, FMVSS 216a asks for 3.0 times the unloaded weight × 9.8 within 127 mm for cars up to 2,722 kg GVWR.

Enter your roof's lengths, curvatures and bow sections: the calculator gives W per zone, Qr and s per bow, a plan view and a how-many-bows sweep, then the roof crush force, the IIHS bands and a check of your report. Skill-Lync read 700 public reports from its Automotive Sheet Metal Design course: in 152 of 248 checkable snow load rows, s is outside 250 to 380 mm and the row still says OK. Free, runs in your browser.

Course formulas as copied in 537 reports (origin not published) · 49 CFR 571.216a, 571.216, 571.3 · IIHS roof strength protocol V (Nov 2022) · NIST SP 811 · checked against a separate solution (2,614 checks at build) · Updated 22 Nov 2026

Bows (and a centre roof rail, if your roof has one)

MemberY (mm)Lx (mm)Iy (mm⁴)Rx (mm)Ry (mm)
Bow 1
Bow 2
Bow 3

Panel zones between neighbouring members

Panel zonel (mm)Rx (mm)Ry (mm)
Front rail to bow 1
Bow 1 to bow 2
Bow 2 to bow 3
Bow 3 to rear rail
Bow section helper: I of a hat section
a = 40f = 15h = 20, t = 0.7bending axis for snow (horizontal)

I about the horizontal axis (snow bends the bow in the vertical plane): 5,779 mm⁴. About the vertical axis: 35,699 mm⁴. S to the extreme fibre: 513.4 mm³. Thin-walled centre-line model, as in the section modulus calculator.

Example: medians of 94 public reports (3 members, 4 zones): L, Ly, Lx, t and each zone's Rx, Ry, l are medians of the text tables that recompute. Leave a zone's l blank to use the centre gap; reports measure l as the panel span between two members.

Largest W2.12OK below 2.7
Smallest Qr5.44needs ≥ 3.1
s outside 250-3803 of 3bows
500W 1.63475W 2.01475W 2.12572W 1.96Bow 1s 487Bow 2s 475Bow 3s 524FrontReargaps and s in mm, Ly = 2,022.2 mm
W per panel zone2.73.10Qr at each bow (log scale)1101003.113.28.655.440 front railrear rail 2,022 mm
  • W < 2.7 in all 4 zones (largest 2.119).
  • Qr ≥ 3.1 at every bow (smallest 5.44).
  • s is outside 250 to 380 mm at 3 of 3 bows (487, 475, 524 mm). Even spacing puts s inside the window only with 5, 6, 7 bows over Ly = 2,022.2 mm.
  • What moves W in the first zone: +100 mm of span l adds 0.11; +1,000 mm of R adds about 0.185; +0.05 mm of panel thickness takes off about 0.023. The L term (3.515) is the same in every zone.

W for each panel zone

ZoneCentre gaplR = 2RxRy/(Rx+Ry)1.73e-3 L1.85e-8 R²/t1.10e-3 lWVerdict
Front rail to bow 1500.2406.43,753.23.5150.3470.4471.63OK
Bow 1 to bow 2474.7390.15,508.33.5150.7480.4292.013OK
Bow 2 to bow 3475.1408.95,815.53.5150.8340.452.119OK
Bow 3 to rear rail572.2362.35,413.53.5150.7230.3991.956OK

Qr and s for each bow

BowYL1, L2sMy = Y(Ly−Y)αQrQr ≥ 3.1250 ≤ s ≤ 380
Bow 1500.2500.2, 474.7487.47,61,3040.954513.22yesno
Bow 2974.9474.7, 475.1474.910,21,0131.19478.654yesno
Bow 31,450475.1, 572.2523.78,29,6900.93125.438yesno

How many bows? (even spacing, the mean bow section and curvature)

Bows, evenly spacedGap = sSmallest QrW (l = gap)s in 250 to 380
02,022.2–3.61 NG–
11,011.13.442.5 no
2674.15.812.13 no
3505.66.891.94 no
4404.48.971.83 no
533710.31.76 yes
6288.912.31.7 yes
7252.813.81.66 yes

What are the heat distortion and snow load formulas in the roof challenge?

Two empirical formulas, in millimetres, copied the same way in 537 and 515 of the 700 public reports Skill-Lync read. The heat distortion index W is worked out for each panel zone between two members (front rail, bows, centre roof rail, rear rail):

L is the roof length in X, Rx and Ry the zone's curvature radii, t the roof panel thickness and l the "bow roof span". In 654 of 661 W rows, l is the panel span between the two neighbouring members, a few hundred mm, not the bow's length across the car. The snow load index Qr is worked out at each bow:

Y is the distance from the front rail to the bow, Ly the front-to-rear rail distance, Lx the roof width on the bow, Iy the bow's second moment of area and L1, L2 the gaps to the members on either side. Note that W uses the harmonic mean of Rx and Ry, and Qr the plain mean.

The W limit. Every copy agrees that W < 2.7 is OK. Above that the wording differs: "OK < 2.7 > 3.1" in 179 reports, "OK < 2.7 mm < NG" in 23, a 2.7 to 3.5 band in 10 (1, 2, 3: "provide outer panel reinforcement in the planning stage, and determine whether the reinforcement is needed or not through tests") and plain "OK < 2.7" in 160. The course text gives no verdict between 2.7 and 3.1, so neither does this calculator. Of 14 rows that land there, 12 are labelled OK.

Where the formulas come from. We searched for the coefficients 1.73, 1.85, 1.10 and 2.68, for "Qr" with My = Y(Ly−Y), and for Japanese and Chinese OEM design phrasing and SAE papers on roof panel heat distortion. The only hits were Skill-Lync student reports. The origin is not published in any document we could read. Because the units are fixed at mm, W and Qr are design indexes, not a deflection in mm or a load in N. In metres the same W reads:

Does W decide where the roof bows go?

Only through the span and the local curvature. W has no Y in it: it depends on L, R, t and l. Moving a bow changes the spans l of the two zones next to it and which part of the roof (which Rx, Ry) each zone covers. It does not change L, the biggest term:

For the example's first zone, the L term is 3.515, the R²/t term 0.347 and the l term 0.447. Across 132 public reports with three or more zones, the median L term is 3.52, the R²/t term 0.71 and the l term 0.43. The zones' W within a report differ by a median of 0.454, mostly from R (0.485) and little from l (0.124). So W flags a flat zone (large R), not a bow position. 122 reports say the heat distortion study "predicts the bow roof position"; the snow load check, with Y, s and the 250 to 380 mm window, is the one that ties to the bow layout.

Why do most roof designs miss 250 ≤ s ≤ 380 mm?

Because three members over a roof about 2,000 mm long leave gaps near 500 mm. With even spacing every bow's s equals the gap Ly/(n + 1), so the window needs:

That is 5, 6, 7 bows for the example's Ly = 2,022.2 mm; the table above shows Qr and W for 0 to 7. Unequal spacing does not help much: a bow's s is the average of its two gaps. In the text tables we could recompute, 219 of 248 snow load rows have s outside 250 to 380 mm and 152 still say OK, in 98 reports (1, 2, 3). The course judgement has two conditions; a bow that meets Qr ≥ 3.1 with s = 480 mm meets one of them. 51 reports add embosses after a failed Qr, the fix the 2.7 to 3.5 wording also points to.

Which moment of inertia is Iy for a roof bow?

The one for bending in the vertical plane. Snow presses down, the bow spans across the car, so it bends about the horizontal axis of its cross-section. For a symmetric hat section the principal axes are the horizontal and the vertical one; the vertical-plane value is the horizontal-axis I. For a wide, shallow hat that is the smaller principal value: the example hat (crown 40 mm, depth 20 mm, flanges 15 mm, 0.7 mm sheet, 7° walls) has 5,779 mm⁴ about the horizontal axis and 35,699 mm⁴ about the vertical one. CAD tools list I max and I min; check which axis each belongs to before you pick.

52 public reports give both I max and I min for their bows. Only 14 of them have a snow load table we could match to a stated value: 2 used I max and 3 I min, too few to call a habit. 12 rows have Iy under 100 mm⁴, which for a 0.7 mm hat bow usually means cm⁴ or a dropped power of ten. Section modulus is I over the distance to the extreme fibre; 32 reports copy "distance from the neutral axis to any given fibre".

What does FMVSS 216a require for roof crush?

A rigid plate 762 mm × 1,829 mm, its long axis pitched 5° forward and its short axis rolled 25° outboard, is pushed onto the roof at not more than 13 mm/s, and the test must finish within 120 s (S6, S7). Its forward edge sits 254 mm ahead of the roof's front point. Before the plate has moved 127 mm, the roof must carry (S5.2):

Each side of the roof is loaded in turn, and the 50th percentile adult male head form may see no more than 222 N (S5.1). The standard covers passenger cars, MPVs, trucks and buses up to 4,536 kg GVWR (S3), every car built from 1 September 2015 at 2,722 kg GVWR or less (S8.4). The older Standard 216 asked for 1.5 × unloaded weight × 9.8, capped at 22,240 N for passenger cars. So a 1,500 kg car needs 44,100 N under 216a; a 2,500 kg SUV with a 3,200 kg GVWR needs 36,750 N.

Unloaded weight, not GVW. 49 CFR 571.3 defines unloaded vehicle weight as the vehicle "with maximum capacity of all fluids necessary for operation ... but without cargo, occupants, or accessories that are ordinarily removed". The RADIOSS Neon challenge text, copied in 23 reports, says "FMVSS 216 target load of 47,000 N (= 3 * GVW)":

That is the right force only if 1,598.6 kg is the Neon's unloaded weight; with the GVW, the target is higher than the rule asks. 23 reports copy "3 * GVW" and 8 write 3 × the unloaded weight. Other slips: 69 reports describe an 1,800 × 750 mm plate (the rule's is 1,829 × 762 mm, which 57 give), and 119 write that the load is "applied for 120 sec". The rule's 120 s is a time limit for the whole test.

How did IIHS rate roof strength?

By the strength-to-weight ratio: the largest force before 127 mm of plate travel, divided by the curb weight IIHS measured with full fluids. Both are rounded to whole pounds and the ratio to 0.01 (Roof Strength Test Protocol, Version V, November 2022). One side is tested, at a nominal 5 mm/s, with no headroom criterion:

Good needs 4.00 or more, Acceptable 3.25, Marginal 2.50; below that is Poor. A 1,500 kg car with exactly 4 × 1,500 × 9.80665 N rates SWR 4, Good. IIHS lists the rating as discontinued (2009-22): "virtually all vehicles were earning good ratings", and the FMVSS 216a phase-in from 2013 to 2017 is close to its Good level. IIHS also reports that a driver of a Good-rated vehicle had a 34% lower risk of fatality or serious injury in a rollover than one in a Poor-rated vehicle. 67 public reports say IIHS rates "how fast the car reforms" after a rollover; the protocol measures force against plate travel, nothing else.

  • Good (SWR ≥ 4) for 1,598.6 kg: 62,709 N
  • Acceptable (SWR ≥ 3.25) for 1,598.6 kg: 50,951 N
  • Marginal (SWR ≥ 2.5) for 1,598.6 kg: 39,193 N

How do you find a roof's crown height and radius?

From the chord and the sagitta. For a chord c and a crown height h at the middle:

The example roof width over the first bow, 1,119.7 mm at Rx = 4,105.6 mm, has a crown of 38.35 mm. The W formula averages the two radii harmonically and the Qr formula arithmetically, and the harmonic one is always the smaller:

For the example's first zone (Rx = 5,693.7, Ry = 2,799.2 mm) that is 3,753.2 against 4,246.4 mm. Of 661 W rows, 637 use the harmonic one, 9 the mean and 15 drop the 2.

What did 700 student roof reports get right?

Skill-Lync fetched 700 of 1,663 public automotive roof reports ("Roof Design", "Roof Challenge" and similar; Revit and building roofs left out) on 22 Nov 2026 and recomputed every W and Qr row given as text, from the row's own inputs.

CheckRowsExamples
W rows in text (184 reports)661—
W recomputes within 1% / within 5%495 / 550—
W does not recompute1111, 2, 3
Snow load rows in text (136 reports)343—
Qr recomputes within 1% / within 5%217 / 248—
Qr does not recompute951, 2, 3
Qr below 3.1 but labelled OK10 of 871, 2, 3
s outside 250 to 380 mm but labelled OK152 of 2481, 2, 3

Counts as of 22 Nov 2026, n = 700 public reports, from their text only (tables in images are not counted). Snow load rows are found through α = Y(Ly−Y)Lx²·10⁻¹², so a row with a wrong α is not seen; where two columns could be l, s or Iy, the reading closest to the report was taken. Skill-Lync's own data, a starting point, not a grade.

  • R = 2,972.2 mm is 2RxRy/(Rx+Ry) = 2,972.2 mm, as the formula defines it.
  • W = 1.578 from your inputs; your 1.57 matches (within 1%).
  • W = 1.578 < 2.7: OK by every wording of the course limit.
  • α = Y(Ly−Y)·Lx²·10⁻¹² = 0.9672; yours matches.
  • Qr = 4.323 from your inputs; your 4.323 matches (within 1%).
  • Qr = 4.323 ≥ 3.1: meets the course limit.
  • s = 460.7 mm is outside the course's 250 ≤ s ≤ 380 mm. The judgement has two conditions: a bow with s outside the window is NG even if Qr ≥ 3.1. 219 of 248 checkable Qr rows have s outside 250 to 380 mm (as of 22 Nov 2026).
  • Your report calls this bow OK with s outside 250 to 380 mm. 152 of those 219 rows still say OK, in 98 reports (as of 22 Nov 2026).

What this calculator does not cover

  • Real panel behaviour. W and Qr are course indexes with an unknown origin. Oil canning, dent resistance, paint-bake distortion and snow load on a real roof need a panel FE model or a test.
  • Roof crush simulation. The crush tab gives the force a rule asks for and rates your peak force; it does not predict the force. Run the plate in RADIOSS or LS-DYNA, both sides for FMVSS 216a.
  • Other countries. We did not read a UN, EU or Indian (AIS) roof crush text, so none is checked here.
  • Sections other than a hat. For a closed or unsymmetric bow, get I about the horizontal axis from the section modulus calculator or your CAD tool.
Learn automotive sheet metal design

Roof, hood, door and fender design: master sections, flanges, reinforcements and the checks that place them. The roof challenge is part of Skill-Lync's Automotive Sheet Metal Design course.

Frequently asked questions

What is the heat distortion formula for a car roof bow?

The course formula is W = 1.73×10⁻³L + 1.85×10⁻⁸R²/t + 1.10×10⁻³l − 2.68, with R = 2RxRy/(Rx+Ry), all in mm. W below 2.7 is OK in every copy of the course text. We could not find where the coefficients come from; treat W as a course design index, not a deflection.

What is the snow load criterion Qr for roof bows?

Qr = Iy·t² / [α·s·((Rx+Ry)/2)²·10⁻⁸], with α = Y(Ly−Y)·Lx²·10⁻¹². The course asks for Qr ≥ 3.1 and 250 ≤ s ≤ 380 mm, where s is half the gap to each neighbouring bow or rail added together. Both conditions must hold at every bow.

Does the heat distortion value W decide where the roof bows go?

Partly. W is worked out for each panel zone between two members, so moving a bow changes the span l and the local Rx, Ry. But the roof length term, about 3.52 in the reports, is the same everywhere. In 132 public reports the zones' W differ by a median of 0.45.

What force does FMVSS 216a need for a car roof?

For a vehicle with a GVWR of 2,722 kg or less, 3.0 times the unloaded vehicle weight in kg times 9.8 N, on each side of the roof in turn, before the 762 × 1,829 mm plate moves 127 mm. Heavier vehicles up to 4,536 kg GVWR need 1.5 times. A 1,500 kg car needs 44,100 N.

What strength-to-weight ratio did IIHS need for a Good roof rating?

At least 4.00: the peak force within 127 mm of plate travel divided by the measured curb weight, both rounded to whole pounds. Acceptable was 3.25 or more, Marginal 2.50 or more. IIHS ran the rating from 2009 to 2022 and has discontinued it, because virtually all vehicles were earning Good.

Is the FMVSS 216 roof crush load 3 times the GVW?

No. FMVSS 216a uses the unloaded vehicle weight: full fluids, no cargo, no occupants (49 CFR 571.3). The GVWR only decides the multiplier, 3.0 or 1.5. The Neon challenge's 47,000 N "= 3 × GVW" equals 3.0 × 9.8 × 1,598.6 kg; that mass would have to be the unloaded weight.

Related on Skill-Lync

Sources

  • 49 CFR 571.216a, FMVSS No. 216a Roof crush resistance; upgraded standard: S3, S5.1, S5.2, S6, S7.3 to S7.6, S8, S9 (Cornell LII copy of the eCFR, read 22 Nov 2026).
  • 49 CFR 571.216, FMVSS No. 216: S3, S5 (1.5 × unloaded weight × 9.8, 22,240 N cap for passenger cars), S6, S7; 49 CFR 571.3, definitions of unloaded vehicle weight and GVWR.
  • IIHS, Roof Strength Test Protocol, Version V, November 2022: overview, testing, SWR calculation and Table 1. IIHS, About our tests: Roof strength; Evolution of IIHS ratings ("Roof strength 2009-22", discontinued).
  • NIST Guide to the SI (SP 811), Appendix B.8: pound 0.4535924 kg, pound-force 4.448222 N, lbf/lb = 9.80665 N/kg (exact).
  • The W and Qr formulas and their limits: as copied in Skill-Lync's public roof reports; no published source found (searches of the coefficients, OEM phrasing in English, Japanese and Chinese, SAE papers 2015-01-1340, 2014-01-0366, 2007-01-1696, 910289, and patent US 9773077).
  • Skill-Lync, 700 public roof reports read 22 Nov 2026. scripts/verify/roof.py recomputes every case another way (W and Qr in metres with rescaled coefficients, exact fractions, s from member positions, a hat section from rotated thin strips, a least-squares circle, the FMVSS and IIHS rules re-implemented from the text), 444 cases; the page checks itself against it at build time (2,614 checks).
Free counselling

From a roof challenge to a body design job.

Knowing which number is a regulation, which is a company index and which one your report got wrong is what BIW and sheet metal interviews test. A Skill-Lync counsellor can map the course that fits the role you want.

Talk to a design course counsellor

Free. We call you back, usually the same day.

By submitting you agree to our Terms and Privacy Policy.

Talk to a career counsellor

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.