Underbody coating calculator: layer thickness, added mass, zinc life and DFT readings
Underbody coating is the protective layer on the underside of a car's body. In the factory it is a PVC plastisol, hundreds of µm thick, sprayed onto the e-coated body and cured in the paint ovens. Aftermarket rubberised, bitumen or wax coats go on top of it. This page gives each layer's thickness from data sheets, the mass a coat adds, and how long zinc and steel last in open air.
It is built for the first assignment in Skill-Lync's free lesson Design Engineering Process Overview (Automotive Sheet Metal Design using CATIA V5): "prepare a one-pager report about what underbody coating is", with an Elcometer benchmark of an Etios and a Figo. Skill-Lync read 594 public reports on it: 466 list the same four aftermarket types, 126 name the factory e-coat or PVC step, 0 work out a mass and 0 cite a standard. The fourth tab checks your report.
Akafuah et al. 2016 · Henkel, BASF, Dinitrol, Sika data sheets · ISO 9223 and ISO 9224 (2012) · ISO 19840 rule as DeFelsko and KTA quote it · checked against a separate script (3,048 checks at build) · Updated 22 Nov 2026
Where the coating goes: a floor panel edge, factory stack
Not to scale: thin layers are drawn thicker so the labels fit. Order and bands from Akafuah et al. 2016 (Fig. 2 and Fig. 6: the PVC or urethane underbody coat sits on the e-coat, under the primer). A band reads "no number printed" where no document read gives one.
| Layer | Dry thickness | Source and note |
|---|---|---|
| Steel sheet | — | Your input (the sheet thickness of the part). Not a coating. Enter the part's sheet thickness in tab 3. |
| Zinc (galvanised sheet only) | 7-20 µm | SSAB zinc coating page: guidance thickness per surface, Z100 7 µm to Z275 20 µm; ArcelorMittal: electrogalvanised 5 and 7.5 µm per side. Only on galvanised (GI, GA) or electrogalvanised (EG) sheet. |
| Phosphate conversion coat | — | Akafuah et al. 2016 Fig. 2 shows the layer without a thickness. No thickness printed in the documents read. |
| Cathodic e-coat (ED) | 15-25 µm | Akafuah et al. 2016 Fig. 2 (15-25 µm); §2.2: 20 µm since 1992. BASF CathoGuard 580: 15-22 µm; CathoGuard 800RE: 13-25 µm; Axalta AquaEC 3000: 10-35 µm. |
| PVC underbody coat and seam sealer | — | Akafuah et al. 2016 §2.3: third step, on the e-coat; Henkel Teroson PV 3133 TDS: applied to electro-dip sheet, cured in the paint ovens. No PVC data sheet read prints a thickness. The lesson's Figo readings, 120-700 µm, are this layer's scale. |
| Primer surfacer | 30-40 µm | Akafuah et al. 2016 Fig. 2 (30-40 µm); §2.4: 25-40 µm exterior, near 20 µm interior. |
| Basecoat (colour) | 15 µm | Akafuah et al. 2016 Fig. 2 (metallic base 15 µm). |
| Clearcoat | 30-40 µm | Akafuah et al. 2016 Fig. 2 (30-40 µm). |
| Cavity wax (inside sills and members) | 50-100 µm | Dinitrol High Performance Wax PDS: recommended dry film 50-100 µm; Teroson WX 960: 50-100 µm. Henkel's WX 300 sheet: cavity conservation is applied to new cars. |
The lesson's benchmark: Etios vs Figo, by zone
- Etios readings run 20 to 32 µm. 1 of 3 zones sit inside Akafuah's 15-25 µm e-coat band and all 3 inside the widest maker band read (35 µm, Axalta AquaEC 3000). That is consistent with e-coat alone in the zones measured, not a fact about Toyota's specification.
- Figo readings run 120 to 700 µm: 4.8 to 28 times the top of the e-coat band. That is PVC-coat scale. The instructor says the Figo is coated "on all regions".
- The lesson compares the Indica Vista and i10 too. Their numbers come from slides, not stated in the transcript, so they are not drawn.
Readings as said in the Skill-Lync free lesson (Elcometer for thickness, Niton XLT for composition). The shaded band is Akafuah's e-coat range.
Factory coat vs aftermarket coat
| Product (data sheet) | Where | Density | Solids | Dry film |
|---|---|---|---|---|
| Cathodic e-coat film (BASF CathoGuard 580) 1 | Factory, paint shop | 1.3 (film) g/cm³ | — | 15-22 µm |
| PVC plastisol underbody (Henkel Teroson PV 3133) 2 | Factory, paint shop | 1.2 g/cm³ | 98% wt | not printed |
| Bitumen underbody coat, aftermarket (Dinitrol 4941) 3 | Aftermarket | 1.1 g/cm³ | 69% wt · 60% vol | 300-500 µm |
| Wax underbody / cavity coat, aftermarket (Dinitrol High Performance Wax) 4 | Aftermarket | 0.85 g/cm³ | 47% wt · 50% vol | 50-100 µm |
| Bitumen underbody coat, aftermarket (Sikagard-6060) 5 | Aftermarket | 1.1 g/cm³ | — · 66.7% vol | 400 µm |
- BASF CathoGuard 580 TDS, version 9, Mar 2018: film density 1.30 ± 0.03 g/cm³, thickness 15-22 µm, bake 15 min at 175 ± 10 °C. Deposited from the bath, not sprayed: no wet film or transfer efficiency.
- Henkel Teroson PV 3133 TDS, Dec 2024: density approx. 1.2 g/cm³, solids approx. 98%, solvent free, cures in the paint ovens from 140 °C for 10 min. Volume solids not printed. The example assumes 100% (the 2% that leaves takes no film volume): dry density 1.2 × 0.98 = 1.18 g/cm³. Enter your supplier's figure.
- Dinitrol 4941 PDS (2023-24): density approx. 1.10 g/cm³, dry matter 69% by weight, recommended wet 500-800 µm, dry 300-500 µm. Volume solids 0.60 is implied by the sheet's own 500 µm wet → 300 µm dry (800 → 500 gives 0.625).
- Dinitrol High Performance Wax PDS: density 850 kg/m³ at 23 °C, dry matter 47% by weight, recommended wet 100-200 µm, dry 50-100 µm. Volume solids 0.50 is implied by the sheet's wet and dry films (100 → 50 and 200 → 100 µm).
- Sikagard-6060 PDS, version 02.01 (03-2023): density (uncured) 1.1 kg/l, solid content 65%, film thickness wet 600 µm, dry 400 µm. Volume solids 2/3 from the sheet's 600 µm wet → 400 µm dry. The 65% solid content has no basis printed, so the dry mass needs your weight-solids figure.
| Zone | Area, m² | DFT | WFT | Dry film, L | Dry mass, kg | Wet material, kg | To spray, kg |
|---|
Example inputs, made up: the five zone areas (Front floor 1.2 m², Rear floor 1 m², Wheel arches (4) 1 m², Sills / rocker panels 0.4 m², Crossmembers, fuel-tank area 0.4 m²) are not measured from any car. Measure your car's coated areas, or take them from CAD. Spray loses material to overspray, so the transfer efficiency is below 100% in practice; type your process's figure (none is printed in the sheets read).
- Same 4 m² at 25 µm of e-coat (film density 1.3 g/cm³): 130 g. At 400 µm of PVC: 1.88 kg, 14 times more.
Which category is a measured first-year rate?
Example readings, made up for a PVC zone with a 400 µm nominal. Paste your Elcometer readings.
- Mean 426 µm ≥ nominal 400 µm
- No reading below 80% of nominal (320 µm)
- 3 of 10 readings (30%) between 80% and 100% of nominal: must be fewer than 20%
Check my report
Tick what your one-pager does. Each flag says what to add.
What is underbody coating?
Underbody coating is a sprayed layer on the underside of a car's body that keeps water, salt and stone chips off the steel. In a car factory it is part of the paint shop. The welded body (body in white) is cleaned and phosphated, dipped in the cathodic e-coat bath, baked, and then robots spray PVC (polyvinyl chloride) plastisol on the floor, wheel arches and sills and run seam sealer along the joints. That PVC cures in the same ovens as the primer and paint.
Akafuah et al. (2016) list the five steps in this order: pretreatment, electrodeposition (ED), "a sealer like Poly Vinyl Chloride (PVC) ... for anti-corrosion, elimination of water leaks, and minimization of chipping and vibrational noise", primer, then basecoat and clearcoat. Henkel's Teroson PV 3133 data sheet says the same from the supplier's side: the material "is applied to electro-dip steel sheets" and cures "in the painting ovens of the production line from a temperature of 140°C at 10 minutes minimum". The paint shop lesson in the same free course shows the line: Automotive paint shop process from ED coating to inspection.
Most student reports skip all of this. 466 of the 594 read list four aftermarket undercoat types copied from consumer blogs, and 368 of those never name the e-coat or PVC. The factory layer already exists on most cars; an aftermarket coat goes on top of it.
How thick is underbody coating?
Each layer is a different order of size. The e-coat is tens of µm: 15-25 µm in Akafuah's Fig. 2, "the current value of 20 µm" in the text, and 15-22 µm on BASF's CathoGuard 580 sheet. The whole visible paint stack is about 100 µm (Fig. 2; PPG says 90-120 µm for an OEM finish). The PVC underbody coat is hundreds of µm, but none of the PVC data sheets read prints a thickness. Measured cars fill that gap.
In the lesson's benchmark, the Etios read 20-32 µm, inside the e-coat bands above. The Figo read 120-700 µm, 4.8 to 28 times the e-coat. So "underbody coating thickness" depends on which layer is under the gauge. Aftermarket products print their own: Dinitrol 4941 bitumen 300-500 µm dry, Sikagard-6060 400 µm dry, Dinitrol High Performance Wax 50-100 µm dry.
The "2-3 mm" in 33 reports is a brushed-on aftermarket figure. BOLL prints 2 to 4 mm and Mipa about 3 mm for brushable grades. It is ten times the spray grades and a hundred times the e-coat, so it should not be given as the factory coat's thickness.
Is underbody coating worth it for a new car?
Start from what the car already has. The modern paint process e-coats the whole body (Akafuah et al.), and PVC underbody coat and seam sealer are sprayed in the paint shop where the maker specifies them (Henkel's Teroson PV 3133 is one such product). An aftermarket coat is a second barrier over those. It is most useful where the factory coat is thin or missing (the Etios readings are consistent with e-coat only), where it has been chipped, and where salt or wet mud sits on the floor for long.
Three honest limits. A coat sprayed over dirt or rust seals them in. Wax and oil products stay soft and need topping up: Krown says "each application lasts about one full year, which is why annual treatment is recommended", while Henkel's Teroson WX 300 cavity wax is for "follow-up treatment after 2 - 3 years". And no price is given here: dealer quotes vary, and none was read from a dated maker page.
How much weight does underbody coating add?
Mass is area times dry film thickness times the density of the dry film. If a sheet prints only the wet density and solids, the dry-film density follows from weight solids sw and volume solids sv:
For the example 4 m² at 400 µm of PVC (Henkel's 1.2 g/cm³ and 98% solids, volume solids assumed 100%, so 1.176 g/cm³ dry):
Per m² for every 100 µm of dry film: PVC 0.118 kg, e-coat 0.13 kg, Dinitrol 4941 bitumen 0.127 kg (1.265 g/cm³ dry), Dinitrol wax 0.08 kg (0.799 g/cm³ dry). Spraying 400 µm of the bitumen over the same area at a 60% transfer efficiency (an example figure) uses 4.9 kg of wet product.
158 reports say the coat "adds weight"; 31 copy "10 to 20 pounds", which is 4.5 to 9.1 kg (1 lb = 0.4536 kg, NIST SP 811). On the example area that would take 1 to 1.9 mm of PVC-density coat. Henkel puts the scale another way: its low-density PVC sealers save "approximately 4 kilograms per vehicle" against conventional ones.
What do the ISO 9223 corrosivity categories mean?
ISO 9223:2012 classes how corrosive the open air is by the first-year loss of standard flat plates. Each band is open at the bottom and closed at the top (C1 is "r ≤" its limit), as Table 2 prints it:
| Category | Steel, g/(m²·a) | Steel, µm/a | Zinc, g/(m²·a) | Zinc, µm/a | Typical outdoor environment |
|---|---|---|---|---|---|
| C1 Very low | ≤ 10 | ≤ 1.3 | ≤ 0.7 | ≤ 0.1 | Dry or cold zone, very low pollution and time of wetness, e.g. certain deserts, Central Arctic/Antarctica |
| C2 Low | 10 - 200 | 1.3 - 25 | 0.7 - 5 | 0.1 - 0.7 | Temperate zone (dry or cool) with minimal pollution (SO₂ < 5 µg/m³), short time of wetness |
| C3 Medium | 200 - 400 | 25 - 50 | 5 - 15 | 0.7 - 2.1 | Temperate zone with medium pollution (SO₂ > 5 to ≤ 30 µg/m³) or some effect of chlorides |
| C4 High | 400 - 650 | 50 - 80 | 15 - 30 | 2.1 - 4.2 | Temperate, subtropical to tropical, low to high pollution (SO₂ > 30 to ≤ 90 µg/m³) |
| C5 Very high | 650 - 1,500 | 80 - 200 | 30 - 60 | 4.2 - 8.4 | Subtropical to tropical, periods of time of wetness, very high industrial pollution |
| CX Extreme | 1500 - 5,500 | 200 - 700 | 60 - 180 | 8.4 - 25 | Subtropical to tropical, extended time of wetness, very high industrial pollution (SO₂ > 250 µg/m³) |
Rates: ISO 9223:2012 Table 2. Descriptions: American Galvanizers Association, "HDG corrosion rates for ISO categories C1-C5, CX" (2 Dec 2021), Table 2, which refers to ISO 9223 Table C.1. The µm columns are the g columns divided by the metal's density and rounded (Table 2 NOTE 2), so a rate near a boundary can fall in different categories in the two units. No Indian city is mapped to a category here: no source read does it.
How long does a zinc coat last? ISO 9224
Galvanised sheet carries its zinc on both faces. In EN 10346 the number after Z is the minimum total of both sides in g/m² (SSAB: "minimum total coating mass, both surfaces"), so a side carries half. With zinc at 7.14 g/cm³ (GalvInfoNote 1.1), 1 µm on 1 m² is 7.14 g:
SSAB's guidance for Z275 is 20 µm per surface and for Z100 7 µm. ArcelorMittal offers Z100 to Z225 Extragal for car body parts, and electrogalvanised sheet at 5 and 7.5 µm per side. ISO 9224:2012 gives the loss over years:
with b = 0.523 for carbon steel and 0.813 for zinc (Table 2, B1; B2 = 0.575 and 0.873 for an upper limit). The standard says Eq. 1 holds for "exposures of up to 20 years" and that a straight line from 20 years "yields the maximum estimate of attack". The time to lose a thickness D inverts either form:
At the top of C3, carbon steel loses:
Eq. 1 alone gives 344 µm at 40 years, less than Eq. 3's 365. With Z100 zinc (7 µm a side) at the top of C3, the zinc is gone in 4.4 years and a 0.8 mm sheet loses its full thickness from one side in 114 years (205 with Eq. 1). At the top of CX the same sheet lasts 1.5 years. The next section says why neither number can be read as a car's life.
Why ISO 9223 is not an underbody life prediction
The categories describe air, measured on clean plates exposed to rain and sun. An underbody is a different place. Wet mud is held against the panel for days, salt water splashes up, stones chip through the coats, and spot-welded flanges and hems make crevices. ISO 9224 says crevices and sheltered areas "experience significantly higher corrosion damage than predicted", and it does not address crevice, pitting or galvanic corrosion. So treat tab 3 as a baseline: it shows how quickly bare zinc and steel go even in open air, and why the e-coat, PVC and cavity wax matter.
How do you check DFT readings? The ISO 19840 80-20 rule
An Elcometer-type gauge on steel reads the coating by magnetic induction (Elcometer's 456 manual: ferrous probes "measure non magnetic coatings on ferro-magnetic substrates"). One reading proves little. ISO 19840 accepts an area when, as DeFelsko's and KTA's summaries word it:
The made-up example in tab 4 has a mean of 426 µm against a 400 µm nominal and no reading under 320 µm, yet it fails: 30% of the readings sit between 80% and 100% of nominal. Exactly 20% also fails, because the rule says "less than 20%" (DeFelsko's Q&A on the same page says "more than 20%", so check the standard if your batch sits at exactly 20%).
ISO 19840 is written for protective paint on rough (blasted) steel structures and "does not apply to nominal dry-film thicknesses less than 40 µm" (ISO's page for the 2012 edition), which leaves out the e-coat. It also adds a roughness correction (Elcometer: 10, 25 or 40 µm for fine, medium or coarse profiles) that smooth car sheet doesn't need. On a car underbody, use it as a strict, written rule set for a PVC or aftermarket coat, and say so in the report. The page shows the statistics for any readings.
What did 594 student underbody coating reports say?
Skill-Lync fetched 600 of the 2,144 public "Underbody Coating" reports at random and read the 594 with real text (report dates 2018 to 2025). Each row counts reports, not mentions.
| What the report does | Reports of 594 |
|---|---|
| List the four aftermarket types (rubberised, polyurethane, wax, asphalt) | 466 |
| ... and never name the factory e-coat (ED) or PVC step | 368 |
| Name the e-coat / ED step | 108 |
| Name PVC | 99 |
| Give any thickness with a unit | 43 |
| Copy "2-3 mm" as the coating thickness | 33 |
| Say the coat adds weight | 158 |
| ... with "10 to 20 pounds" (no source) | 31 |
| Work out a mass | 0 |
| Say "re-apply once a year" (almost always of wax) | 140 |
| Copy "Most vehicles make it five years before corrosion begins" | 58 |
| Name an Elcometer | 10 |
| Mention zinc or galvanising | 49 |
| Cite any standard (ISO, ASTM, SAE, DIN, JIS) | 0 |
- Consumer lists, not engineering. The four-type list and its pros and cons ("adds weight", "re-apply once a year", "five years before corrosion") are copied from consumer blogs. They describe products a car owner buys, not the paint shop.
- One table copied 11 times. A four-row Figo table (front floor 665 µm and so on) appears in 11 reports with no source. The lesson's own readings are ranges by zone.
- No standard. 0 reports cite ISO, ASTM, SAE, DIN or JIS.
Counts as of 22 Nov 2026, n = 594, from the text of each report, with hits read by hand (Skill-Lync's own data, a starting point, not a grade). Text in images isn't counted. Example report: Underbody coating.
What this page does not cover
- PVC thickness specs. No PVC data sheet read prints a film thickness or volume solids; the example assumes 100% volume solids and the Figo readings show the scale.
- Phosphate coating weight. Not printed in the documents read, so the layer has no number.
- Prices. No dealer or maker price was read from a dated page.
- SSPC-PA 2. Only maker summaries were readable and none gave the edition, so it is not offered as a second rule set.
- Corrosion tests on painted panels or whole vehicles. Not modelled; the corrosion tab is bare zinc and steel in open air.
Underbody coating is one of the first benchmarking studies in Skill-Lync's Automotive Sheet Metal Design course: measure, compare by zone, and set your car's target from the competitor data.
Frequently asked questions
What is underbody coating on a car?
A protective layer on the underside of the body. In the factory it is a PVC plastisol sprayed onto the e-coated body and cured in the paint ovens, sealing seams and taking stone chips. Under it sit the e-coat, the phosphate and, on galvanised sheet, zinc. Dealer "anti-rust" coats go on top of all that.
Is underbody coating worth it?
A modern body leaves the paint shop e-coated, with a PVC underbody coat where the maker specifies one. An aftermarket coat adds a second barrier on top. It helps where the factory coat is thin, missing or chipped, and where salt or mud sits on the floor. Sprayed over rust or wet dirt, it seals them in.
How thick is underbody coating?
The e-coat is about 15 to 25 µm (Akafuah et al. 2016). In the Skill-Lync lesson's benchmark, a Figo read 120 to 700 µm where PVC was sprayed, and an Etios read 20 to 32 µm, the e-coat range. Aftermarket bitumen coats print 300 to 500 µm dry, wax coats 50 to 100 µm.
How much weight does underbody coating add?
Area times dry film thickness times dry-film density. A PVC coat at about 1.18 g/cm³ adds 0.118 kg per m² for every 100 µm. Over an example 4 m² at 400 µm that is 1.9 kg. The "10 to 20 pounds" copied in student reports has no source.
What is the 80-20 rule for dry film thickness?
ISO 19840's acceptance rule, as DeFelsko and KTA quote it: the mean must reach the nominal DFT, no reading may fall below 80% of nominal, readings between 80% and 100% are allowed only if they are fewer than 20% of all readings, and none may exceed the maximum DFT if one is set.
What are the ISO 9223 corrosivity categories?
Six classes of how corrosive the open air is, from C1 (very low) to CX (extreme), set by the first-year corrosion of standard steel and zinc plates. For carbon steel C3 is 25 to 50 µm in the first year and CX 200 to 700 µm. They describe the air, not a car's underbody.
Related on Skill-Lync
- What is body in white (BIW)?
- Vehicle benchmarking calculator: weighted car matrix and steel vs aluminium panel thickness
- Bend allowance calculator: sheet metal flat lengths
- Plastic and sheet metal design courses
- All free engineering tools
Sources
- N. K. Akafuah, S. Poozesh, A. Salaimeh, G. Patrick, K. Lawler, K. Saito, "Evolution of the Automotive Body Coating Process: A Review", Coatings 6(2):24, 2016 (PDF, read 22 Nov 2026): Fig. 2 layer thicknesses, §2 step order, §2.2 e-coat, §2.3 UBC and seam sealing, §2.4 primer.
- PPG Refinish, "OEM Film Builds": "approximately 90-120 µm". BASF CathoGuard 580 and 800RE data sheets: film 15-22 and 13-25 µm, film density 1.30 g/cm³. Axalta AquaEC 3000: 10-35 µm.
- Henkel Teroson PV 3133 TDS, Dec 2024: density approx. 1.2 g/cm³, solids approx. 98%, solvent free, cures in the paint ovens from 140 °C for 10 min.
- Dinitrol 4941 PDS (2023-24): density approx. 1.10 g/cm³, dry matter 69% by weight, recommended wet 500-800 µm, dry 300-500 µm.
- Dinitrol High Performance Wax PDS: density 850 kg/m³ at 23 °C, dry matter 47% by weight, recommended wet 100-200 µm, dry 50-100 µm.
- Sikagard-6060 PDS, version 02.01 (03-2023): density (uncured) 1.1 kg/l, solid content 65%, film thickness wet 600 µm, dry 400 µm.
- Henkel, "Paint Shop Sealants & Coatings" brochure (2022): low-density PVC sealers save "approximately 4 kilograms per vehicle". Henkel Teroson WX 300 TDS: follow-up "after 2 - 3 years". Krown FAQ: "annual treatment is recommended". BOLL Underbody Brushable: "2 to 4 mm"; Mipa Unterbodenschutz brushable: "approx. 3 mm".
- ISO 9223:2012, Table 2 and clause 8.2, and ISO 9224:2012, clauses 4-7 and Table 2 (official previews, standards.iteh.ai, read 22 Nov 2026). American Galvanizers Association, "HDG corrosion rates for ISO categories C1-C5, CX" (2 Dec 2021), Table 2, which refers to ISO 9223 Table C.1.
- SSAB, zinc coating page (Z designations, guidance µm per surface); thyssenkrupp, hot-dip coated sheet Z product information (Jan 2023); ArcelorMittal Automotive, Extragal and electrogalvanized pages; GalvInfoNote 1.1 Rev 4.0 (Dec 2020) p. 5: zinc density 446 lb/ft³ [7140 kg/m³]; American Galvanizers Association: 7.133 g/cm³.
- DeFelsko PosiTector 6000 ISO 19840 addendum and KTA-Tator "Differences between coating inspection standards" (20 May 2024), Table 8; ISO committee page for ISO 19840:2012 (scope, 40 µm); Elcometer 456 manual (TMA_0489 issue 10): probes and ISO 19840 correction values. NIST SP 811 Appendix B.9: pound = 0.453 592 37 kg.
- Skill-Lync free lessons Design Engineering Process Overview and Complete automotive paint process (Automotive Sheet Metal Design using CATIA V5): the assignment and the Etios / Figo Elcometer readings.
- Skill-Lync, 594 public Underbody Coating reports read 22 Nov 2026. scripts/verify/underbody.py redoes every number with exact fractions, numeric integration of the ISO 9224 rate, a root finder and numpy, 709 cases; the page checks itself against it at build time (3,048 checks).