A-pillar obscuration calculator: the UN R125 6° binocular angle, the widest pillar and your master section

UN Regulation No. 125 allows each A-pillar a binocular angle of obstruction of at most 6°. It is measured in plan from two eye points 65 mm apart, each 104 mm from the head pivot P1, on two pillar sections cut by planes 2° above and 5° below the horizontal through Pm. A flat section square to the sight line can be at most 65 + D·tan 6° wide: 138.6 mm at 700 mm from the eye.

Enter the R point, seat-back angle and each pillar's section: the calculator places P1, P2 and Pm, cuts S1 and S2, turns the eyes as the regulation says and gives each pillar's angle against 6°, drawn to scale. Tab 2 shows how much angle each layer of your master section costs; tab 3 checks a report. Skill-Lync read 416 public A-pillar reports from its Automotive Plastic Design course: 0 work out the angle. Free, runs in your browser.

UN R125 01 series + Supplement 1 (ADR 93/00 Appendix A copy) · Directive 77/649/EEC, 88/366/EEC · AIS-021 · 49 CFR 571 · checked against a separate solution (11,743 checks at build) · Updated 22 Nov 2026

Driver-side pillar: plan section at height Z

Examples are illustrative shapes, not measured cars: a left-hand-drive layout with the R point at X 2,400, Y -370, Z 300 mm (car axes: X rearward, Y to the right, Z up) and a design seat-back angle of 25°. The rectangle is the pillar's horizontal section at height Z; rake and lean move it as it rises, which sets S1 and S2.

Driver side3.72°passes 6°
Passenger side-0.45°symmetric: not required
Head turn23.8°left, about P1
Rfront ↑ · plan view, to scale3.72°-0.45°E1, E2E3, E4
3.72°S1S2Driver-side pillar: S2 solid, S1 dashed, front ↑
Head close-up, to scale: eyes 104 mm from P, 65 mm apartRPmP1P2E1E2E4E3
05010015020040060080010001200140065 mm: 0°widest section for 6° (mm)distance from the eye along the sight line (mm)109.1 mm at 680 mm
  • Driver-side A-pillar: binocular angle 3.72° against 6°: passes with 2.28° to spare, about 27.3 mm of extra width at the inner edge. Monocular: 12.17° from the outer eye, 14.17° from the inner eye.
  • Passenger-side A-pillar: -0.45° (shown for interest: para 5.1.2 does not require it when the two pillars are symmetric about the car's centre plane).
  • Pm at 43.36 mm behind R and 627 mm above it. S1 is cut 653.7 mm and S2 544.9 mm above R on the driver side.

What does UN R125 say about A-pillar obstruction?

Paragraph 5.1.2: "The angle of obstruction for each 'A' pillar ... shall not exceed 6°". For armoured vehicles the limit is 10°. The passenger-side pillar "need not be determined if the two pillars are located symmetrically in relation to the median longitudinal vertical plane of the vehicle", and no vehicle may have more than two A-pillars (5.1.2.2).

An A-pillar is "any roof support forward of the vertical transverse plane located 68 mm in front of the V points" and it "includes non-transparent items such as windscreen mouldings and door frames, attached or contiguous to such a support" (2.16). So the angle is set by the whole master section seen from the driver, not by the BIW alone. The regulation covers the 180° forward field of vision of M1 vehicles (1.1) and is worded for left-hand drive; for right-hand drive the criteria are inverted (1.3). Vent and side window division bars are allowed obstructions in their own right (5.1.3), so a front quarter glass bar is not counted as a third A-pillar. There is no direct rule on where the pillar sits, but 5.1.1.1 needs the windscreen's transparent area to include the datum point 17° to the left of V1, which keeps the driver-side pillar outboard of that line.

How is the A-pillar obscuration angle measured?

In five steps, all in plan view, from the driver's R point (the manufacturer's seating reference point). The coordinates are from R, in the regulation's axes: X rearward, Y to the right, Z up, for a 25° design seat-back angle. Table IV moves every P and V point for other seat-back angles (for example -44 mm in X and +11 mm in Z at 20°), and Table III moves P1 and P2 forward by 13 to 48 mm when the seat travel exceeds 108 mm.

1. Head pivots. P1 (for the driver-side pillar) and P2 (passenger side) from Table II; Pm is where the line P1-P2 crosses the vertical plane through R:

2. Two sections. A plane through Pm rising 2° forward cuts the pillar; the horizontal section at the foremost point of that cut is S1. A plane falling 5° gives S2 (5.1.2.1). On a raked pillar S1 sits higher, further back and further inboard than S2:

3. Eye points. E1 and E2 are each 104 mm from P1 and 65 mm apart (5.5.1), so their midpoint is h ahead of P1:

4. Head turn. The line E1-E2 is turned about P1 until the tangent from E1 to the outer edge of S2 is square to E1-E2 (5.5.2). The driver looks straight at the pillar's outer edge with the outer eye.

5. The angle. From E2, draw a parallel to E1's tangent and the tangent to the inner edge of S1. The angle between them is the angle of obstruction (5.1.2.1.1). The passenger side is the mirror: E3 and E4 about P2, E4's tangent to the outer edge of S2, E3's tangent to the inner edge of S1 (5.1.2.1.2, 5.5.4):

The manufacturer may measure it on the vehicle or on the drawings (6.1.5). The calculator reads the inclined planes as perpendicular to the X-Z plane, as Annex 4 Figure 2 draws them in side view, and models the pillar near the eye level as a straight prism along the rake and lean you enter.

Worked example: the slim hatchback pillar

The first example is illustrative: left-hand drive, R at X 2,400, Y -370, Z 300 mm, seat back 25° and seat travel 108 mm, so no Table III shift. The pillar's horizontal section at Z = 927 mm is a 50 × 160 mm rectangle centred at X 1720, Y -690, its long side 15° from the X axis, raked 58° and leaning 22° inboard. Head pivot and Pm in car coordinates:

The 2° and 5° planes meet the pillar's front at these heights, and the head turns until E1's tangent to S2's outer edge is straight ahead:

E2's tangent to the inner edge of S1 points β2 to the left of straight ahead, so:

That is 2.28° inside the limit. Seen from one eye the same pillar covers 12.17° (E1) and 14.17° (E2): the regulation counts only what both eyes miss. The SUV example gives 5.68°, the quarter-glass MPV 1.76° and the last example 6.96°, which fails.

How wide can an A-pillar be for 6°?

For a flat section square to the sight line, D mm ahead of E1, the outer eye's tangent is straight ahead and the inner eye sits 65 mm to the side, so the binocular angle and the widest section are:

That is 128.1 mm at 600 mm, 138.6 mm at 700 mm and 149.1 mm at 800 mm. A section narrower than 65 mm has a negative angle: every point behind it is seen by one eye or the other. Each extra millimetre of width costs:

About 0.081° per mm at 700 mm, or 12.4 mm per degree. Real sections are not flat: a raked pillar's horizontal section is long fore and aft, and its apparent width depends on how it is turned to the sight line. That is why tab 1 works from the section's points.

Which master section layer uses up the 6°?

The one with the most width across the sight line, usually the BIW itself. With the example stack (70 mm BIW, 14 mm windscreen flange and bead, 20 mm door frame and seal, a 2.5 mm trim wall with a 1.5 mm gap wrapping both edges) at 800 mm the total is 112 mm, 3.36°, leaving 37.1 mm. The 2.5 mm trim wall is the course value; the rest are example numbers, not a standard. Draft (3° in the course), ribs and dog houses on the trim are in the plastic part design calculator.

The strength side. For a thin box of total sheet t, depth h along the sight line and width b across it, the bending stiffness about the axis along the depth grows with about b³; about the other axis it grows with b. In the example, going from 70 to 80 mm wide raises the first I by 35% and the second by 10%, and costs 0.71°. This is the course's "wider is stronger but blocks the view" with numbers on both sides. Roof crush (FMVSS 216a, see the car roof design calculator) and frontal crash loads are not computed here.

Which countries apply the 6° A-pillar rule?

UN and EU. UN R125 (01 series, in force 15 July 2013, Supplement 1 from 8 October 2016) is the text this page follows. The EU General Safety Regulation 2019/2144 lists R125 01 series for M1 in Annex I, and its Annex II item B8 "Forward vision" applies R125 to M1 and N1. The 02 series (ECE/TRANS/WP.29/2021/100) adds rules for Field of Vision Assistants and leaves paragraphs 5.1.2 and 5.5 alone. We did not read the 03 series text.

History. R125 comes from Directive 77/649/EEC. Its 1977 text allowed 7° until 30 September 1981 and 6° after, measured in a horizontal plane through P1 and P2 with the eye line square to the car's centre plane (or at 120° to the pillar tangent). Directive 88/366/EEC brought in the S1 / S2 sections and the head turn used today.

India. AIS-021 (2004, Amendment 1 of October 2011) has the same 6° rule, the same 104 mm and 65 mm eye geometry and the 2° / 5° sections, written for right-hand drive (P1 at Y +20 mm, P2 at −47 mm). ICAT's M1 ready reckoner lists "Driver's field of vision", AIS-021:2004, for CMVR type approval under rule 124(1)(34). Australia's ADR 93/00 accepts R125 up to the 01 series as an alternative standard for passenger cars (MA, MB, MC).

United States. No federal rule. None of the standards in 49 CFR 571 sets a forward field of view or an A-pillar obscuration limit; FMVSS 104 is windshield wiping, 111 rear visibility, 205 glazing materials. Measured cars are often above 6° on other methods: Ekroll and others (2021) quote Quigley and others (2001) for an average driver-side binocular obscuration of 7.3° (5.4° to 9.4°). We could not open Quigley's report, so we do not reproduce that number here.

What do student A-pillar reports say about the driver's view?

Skill-Lync looked at 600 of 1,395 public "A pillar Design with Master Section" report titles at random on 22 Nov 2026: 585 were A-pillar reports and 416 had text we could read. The project is a plastic trim part built from a Class-A surface and a master section.

Of 416 public A-pillar reports with text we readReports
Set a tooling axis or direction398
Draw a dog house385
Use a 2.5 mm trim wall (Class-A offset)251
Use a 3° draft232
Mention vision, visibility or blind spot at all14
Say strength must be traded against vision13
Work out an obscuration angle0
Name UN R125 or 77/649/EEC0

Counts as of 22 Nov 2026, n = 416 public A-pillar reports with text, from a random 600 of 1,395 titles; not every report. Skill-Lync's own data, a starting point, not a grade. Examples: a tooling axis and dog house report, a report with the strength-versus-vision sentence.

  • No regulation named. The A-pillar rule is UN R125 para 5.1.2 (the same text as EU Directive 77/649/EEC as amended by 88/366/EEC, and India's AIS-021): each A-pillar's angle of obstruction must not exceed 6°. Fix: cite it in the introduction. 0 of 416 public A-pillar reports with text we read name UN R125 or 77/649/EEC (as of 22 Nov 2026).
  • No limit stated. Fix: "the angle of obstruction for each A-pillar shall not exceed 6°" (UN R125 para 5.1.2).
  • No obscuration angle worked out. Fix: superimpose S1 (2° up through Pm) and S2 (5° down), place E1 and E2 104 mm from P1 and 65 mm apart, turn them about P1, and measure the angle (tab 1 does this). 0 of 416 public A-pillar reports with text we read compute an obscuration angle (as of 22 Nov 2026).
  • No eye points given. Fix: R point → P1 (35, −20, 627 mm from R at 25° seat back) → E1, E2 each 104 mm from P1, 65 mm apart (Table II, para 5.5.1).
  • Estimate for a flat section 120 mm wide, square to the sight line, 700 mm from the eye: atan((120 − 65)/700) = 4.49°, within 6°. The widest such section at that distance is 138.6 mm.
  • "Wider is stronger but blocks the view" needs a number on the vision side. Fix: give the angle of obstruction against 6° and the section's I against its width (tab 2). 13 of 416 public A-pillar reports with text we read say strength must be traded against vision, with no number (as of 22 Nov 2026).

What this calculator does not cover

  • Curved pillars. The pillar is a straight prism near eye level. If your pillar curves between the S1 and S2 heights, cut both sections in CAD and enter them as points with zero rake (S1 = S2 then); for separate S1 and S2 shapes, take the worse case.
  • The rest of R125. The windscreen datum points (17° left, 7° up, 5° down from V1 and V2), the 180° obstruction rule below V1 and the area S are not checked.
  • Strength. Only the I of a thin box. Roof crush, frontal and small-overlap crash loads need an FE model; see the section modulus calculator for any other section.
  • The 03 series and other rules. Not read; China's GB 11562 was not checked.
Learn automotive plastic design

A-pillar, B-pillar and door trims from a Class-A surface and a master section: tooling axis, draft, dog houses, ribs and the checks a design review asks for. The A-pillar project is part of Skill-Lync's Automotive Plastic Design course.

Frequently asked questions

What is the maximum A-pillar obstruction angle allowed?

6° for each A-pillar under UN Regulation No. 125, paragraph 5.1.2, and 10° for armoured vehicles. The passenger-side pillar need not be measured when the two pillars are symmetric about the car's centre plane. The same 6° is in EU Directive 77/649/EEC as amended and in India's AIS-021.

How is the A-pillar obscuration angle measured?

Two horizontal sections of the pillar are superimposed in plan: S1 where a plane 2° up through Pm meets it, S2 where a plane 5° down meets it. Eyes E1 and E2, 104 mm from P1 and 65 mm apart, turn until E1's tangent to S2's outer edge is square to E1-E2; the angle to E2's tangent to S1's inner edge is measured.

Is the A-pillar blind spot angle monocular or binocular?

Binocular. R125 measures the angle hidden from both eyes, so it is the monocular angle less roughly the 65 mm eye spacing seen at the pillar. A flat section 139 mm wide, square to the sight line 700 mm from the eye, gives exactly 6°. A section narrower than 65 mm gives a negative angle.

Does India have an A-pillar obstruction rule?

Yes. AIS-021 (2004, with amendments) applies the same 6° rule to M1 cars, written for right-hand drive, and ICAT's ready reckoner lists it for CMVR type approval under rule 124(1)(34). Its eye-point and section method is the one in UN R125; for a right-hand-drive car the figures are mirrored.

Is there a US FMVSS rule for A-pillar width?

No. None of the 49 CFR 571 standards sets a forward field of view or A-pillar obscuration limit. FMVSS 104 covers windshield wiping, 111 rear visibility, 205 glazing materials and 216a roof crush, which pushes pillars stronger. The 6° binocular rule is UN R125, used in the EU, India and Australia.

How much wider can an A-pillar get for 1 degree?

About 12.4 mm at 700 mm from the eye, from α = arctan((w − 65)/D). Every millimetre the master section adds across the sight line, BIW, urethane bead, door seal or trim wall, costs about 0.081° there. Moving the pillar 100 mm further from the eye allows about 10.5 mm more width.

Related on Skill-Lync

Sources

  • UN Regulation No. 125, 01 series of amendments and Supplement 1 (entry into force 15 July 2013 and 8 October 2016), as reproduced in Australian Design Rule 93/00 Appendix A (F2018L01521): paras 1.1, 1.3, 2.14 to 2.16, 5.1.2 to 5.1.2.2, 5.2 to 5.5 with Tables I to IV, 6.1.4, 6.1.5, Annex 4 Figures 1 to 5 (read 22 Nov 2026).
  • ECE/TRANS/WP.29/2021/100, proposal for the 02 series of amendments to UN R125 (Field of Vision Assistant; paras 5.1.2 and 5.5 not amended).
  • Council Directive 77/649/EEC (OJ L 267, 19.10.1977), paras 5.1.2 and 5.5 of Annex I; Directive 88/366/EEC (the S1 / S2 method); Directives 81/643/EEC and 90/630/EEC (EUR-Lex). Regulation (EU) 2019/2144, Annex I and Annex II item B8.
  • AIS-021 (December 2004) and Amendment 1 (October 2011), Field of Vision of Motor Vehicle Drivers for M1 Category, paras 1.2, 3.1.2, 3.3, 3.5; ICAT, Ready Reckoner M1 Category CMVR Type Approval (2025), item 53.
  • 49 CFR Part 571, the list of Federal Motor Vehicle Safety Standards (eCFR, read 22 Nov 2026).
  • Ekroll V. and others, "The illusion of absence: how a common feature of magic shows can explain a class of road accidents", Cognitive Research: Principles and Implications 6:22 (2021), citing Quigley and others (2001).
  • Skill-Lync, 416 public A-pillar reports with text, read 22 Nov 2026. scripts/verify/a_pillar.py recomputes every case another way (Pm by line-plane intersection, S1 and S2 by root finding on each generator, the head turn on a support function, the angles by a dense ray sweep, the widest section by root finding on the full rule, box I by numerical integration), 676 cases; the page checks itself against it at build time (11,743 checks).
Free counselling

From an A-pillar trim to a body and interiors design job.

Knowing which number in a master section is a regulation, which is a course rule and which one your report left out is what trim and BIW interviews test. A Skill-Lync counsellor can map the course that fits the role you want.

Talk to a design course counsellor

Free. We call you back, usually the same day.

By submitting you agree to our Terms and Privacy Policy.

Talk to a career counsellor

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.