Week 8 - Challenge 6 - Core & Cavity Design

AIM : To create the Bumper Design Plastic component through the given Class-A surface.   Objective To create a tooling direction. To perform draft analysis for given A-Surface and prepare the final close body. To design the Bumper plastic component by creating the B-Surface and C-Surface using the given Class-A…

AIM: Create the riband screw boss for the given part folling the design rules.   PROCEDURE:    Draw a line on the base surface of the given part with using position  sketch. Construct the line with using axis. and extrude the this line and add thicknig for this surface. add thickness of the rib 0.4*thickness…

AIM : Create the Core and cavity blocks for the switch bezel designed in the earlier challenge.The core is the part which forms the internal shape of molding. The cavity is the part which forms external shape of molding.Core isthe side of the tool where the plastic part is injected from; also known as the bottom half of…

AIM: Creating  the coin holder plastic component through the A-class surface and add thickness to it    Objective : Creating the B and C surface  Creating the tooling axis  Performing the draft analysis on both A surface and final plastic components. Take the Thickness of the component to be 2.5…

- Aim: Create the Switch Bezel Plastic component through the given Class-A surface. - Objectives: - To create class B & C surface for the given component. - To form the tooling axis and capture the surface properly. - To check the feasibility of the component with a draft of 3 degrees. - Method: - In…

AIM:  to make a model from the provided class-A surface. INTRODUCTION: CLASS-A SURFACE: a surface made by the designer which is given as an input to the plastic modeler to work on. It is aesthetic surface and the outer most surface. CLASS-B SURFACE: a surface below a certain thickness from the class-A…

UNDERBODY COATING:- to explain the underbody coating and its ourpose EXPLANATIION:- underbody is uswally a dense claddding applied uniformally to the undercarrige of the automobile. it is normally sprayed or painted on when the car is just out of the dealership and is clean.But even if you are getting the undercoatting…

SECTION MODULUS CALCULATION AND OPTIMIZATION:- AIM:- calculate the moment of inertia calculate the section modulus (z) INTRODUCTIN:- section modulus is a geometric property for given cross-section used in design of beams or flexural members.other geometric properties used in design include area for tention and shear ,raadius…

Aim: Design a back door of a car by usign class A surface What is a back door? A door whichbis located at rear side of the car which give access to the luggage, spare wheel etc. This door can be operated manually or electri power. most of luxury door operate by electrically.  Types of back door baced on working position …

ROOF DESIGN CHALLENGE  AIM - to design a roof of a car and do the curvature study to resist heat destortion ans snow load condition AUTOMOTIVE ROOF :- an automotive roof ar car top is the portion of an automobile that sits above the passsenger co,partment protecting the vehicle ocuupants from sun,wind,rain, and other…

FRONT FENDER DESIGN:- Objective:- the aim of this project is to design the front fender of a car by tacking into account all design considerations required to design the front fender. INTRODUCTION:- Fender:- fender is the part of vehical that frames the wheel .the primary purpose of the fender is to prevent sand , mud…

BENCHMARKING:- benchmarking is the pocess of measuring the performance of a company's  product services against those of another business considered to the best in company' '' best in class.'' the point of benchmarkink is to identify internal opportunites for the iprovement. by studying compnies with superrior performance…

DESIGN OF HOOD INNER AND OUTER PANEL:- Aim:- TO design hood outer pannel and inner panel , position the striker and hinge and providing emboss and mastic points.   Objective:- here we are going to design and understand the concept of front mounted engine hood according to the standards. the hood is the hinged…

DEESIGN OF SHEET METAL BRACKET -2 USING A NX CAD SOFWARE. OBJECTIVE:- to create a sheet metal part 2 using a vaius operations performed in nx sheet metal software using a 2d drawing INTRODUCTION:- UG NX software is a flexible and powerfull integrated solution that helps you deliver better product faster and more efficiently.…

BRACKET 0BJECTIVE:- observe the model and design the sheet metal by using the given diamentions and instructions. INTRODUCTION:- we design here by using the NX is widely used computr aided design software for multipurpose like designing,engineering and manufacturing. DESIGN METHODOLOGY :- DESCRIPTION:- tool used while…

 TITLE OF PROJECT:- ODD SHAPED ENCLOSURE:- objective:- design the Odd Shaped Enclosure insheet metal using NX CAD. INTRODUCTION:- in this project we design Odd shaped Enclosure using basic sheet metal commands. Design methodology :- DESCRIPTION:- feature tool used to create the odd shaped enclosure:- 1-sketch:- It…

DESIGN OF BOX ASSEBLY:- OBJECTIVE:- the main purpose of this project is to create the sheet metal Box assembly with some apperances by using the sheet metal feature in NX . introduction:- sheet metal is the is formed by an industrial process into the thinand flat pieces. sheet metal is the fundamental formes used in mmetalworking.and…

CASING DESIGN:-   1-  objective:- in this tutorial we learn the step by step the procedure how to design the 'sheet metal casing' using the siemens NX sheet metal application. 2-Introducion:- sheet metal ia a metal formed by varius  idustrial process in to thin,flat pieses. becaus it flate property it can…

DESIGN AND ASSEMBLY OF SUNSEEKER PREDATER YACHT USING SOLIDWORKS:-   Aim and objective:- the objective is to design and assemble the varius parts f yacth by using the solidwork. Introduction:- the yacth design majorly consist of surface modelling. there are varius parts of yacth are designed and assemble together…

DESIGN AND RENDERING OF AMERICAN CHOPPER OBJECTIVE- To learn the diffrent technices of solid work as well as surface modeling using solid work by desingnig American chopper to creat diffrent part of a ameriacn chopper in solidwork using varius types of sketches and fetures tool to assemble the different modelled part…