Radar Mast & Final Assembly of Yacht

DESIGN AND ASSEMBLY OF SUNSEEKER PREDATER YACHT USING SOLIDWORKS:-

Aim and objective:-

• the objective is to design and assemble the varius parts f yacth by using the solidwork.

Introduction:-

• the yacth design majorly consist of surface modelling.
• there are varius parts of yacth are designed and assemble together
• finally Rendering was done by using the solid works visualize software.

parts to be modelled:-

1. radarmast
2. radar
3. hull
4. garage door
5. rear seat
6. middle seat
7. front seat
8. super structure
9. Propeller

1-RADARMAST:-

Radarmast is used for navigation purpose.which is build at the top of the ship

Command used to design radar mast:-

• sketch
• Boss extrude
• revolve
• sweep

SKETCH:-

• sketch is the basically a 2d representation of a particular from a different views sutch sa afront view ,side view,top view etc.the sketh basically comprise the commands like lines,arcs,circle etc.

REVOLVE:-

• revolve is the command is used to revolve the sketch using reference axis.

BOSS EXTRUDE:-

• the extrude command is used to creat a solid extrusion based on selected skecth in bothe the direction

SWEEP:-

• the sweep command is used to create the surface area of the corner in a defined lenth and angle.

1-Isometic view:-

2-back view:-

3-side view:-

2-RADARMAST FEATURE TREE:-

2-RADAR:-

• radar is a device which is use to detect the obstacles or transmit signles.Radar use sound wave to detect the obstacles.

Commands used to desgned radar:-

• sketch
• boss extrude
• fillet
• cut extrude
• sketch pattern
• mirror
• splite line

FILLET:-

• fillet is used to icrease the surface area of part so that the stress will distributed equally through the surface and avoide the breakage

CUT EXTRUDE:-

• the extrude cut is a tool used to remove the material fom the part base on the sketch.

SKECTH PATTERN:-

• sectch pattern is a tool use to make the replica of the skech by using the defined reference in the perticular diamentions to another sketch.

MIRRORE:-

• mirrore is the tool used to dublicate the part with referance to the plane,face or edge.

SPLITE LINE:-

• spite line comand is used to splite or devide the sketch line into diffrent entities.

3- HULL:-

the hull is main body of ship,total base body or water tight body,which is use to float the ship on the water.

Comand use to design the hull:-

• skecth
• projected curve
• loft surface
• fill surface
• surfce exrude
• srface trim
• surface extend
• shell
• boss extrude
• cut extrude
• fillet
• champer
• sweep
• plane
• dome
• Hellix/spiral
• liner parren
• Delete face
• curve
• Revolve
• Combine

PROJECTED CURVE:-

• the project curve is used to create 3d curve using tow diffrent sketchs,it is avilable in the insert menu.

FILL SURFACE:-

• create a surface patch within the boundery defined by existing model edges,skethes or curves

SURFACE TRIM:-

• The surface trim command is used to remove the surface by taking sketch or surface as a referance point

SURFACE EXTRUDE:-

• create an extrude surface based on some referance sketch.

SURFACE EXTEND:-

• surface extend is used to extend the edges of the surface.

SWEEP:-

• the sweep command is also used to increase the surface area of the corner in a defined length and angle.

SHELL:-

• the shell feature is used to thicken the surface

DOME:-

• used to create the dome feature on surface

HELIX /SPIRAL:-

• this command is used to create a spiral or helix based on some referance sketch

COMBINE:-

• used to combine the solids.

DELETE FACE:-

• this tool used to delete the selected face

4-GARAGE DOOR:-

• A garage door is located at the back side of the yacth where you can park the vehical

Commands used to design the garage door:-

• sketch
• shell
• insert text
• Extrude cut
• mirror
• fillet
• champer

INSERT TEXT:-

• is a tool used to text any name on surface of the part.

5-REAR SEAT:-

• used for seatting purpose
• The rear seat is build at the rear side of the yacth above the garage door.

Commands used to create the rear seat:-

• sketch
• surafce sweep
• surface offset
• surface trim
• ruled surface
• surface knit
• surface extend
• surface loft
• boss extrude
• fillet
• champer
• mirror
• Revolve

SURFACE SWEEP:-

• Swept surfaces are the surface that surfaces are generatd from a section curve positioned along a path.

SURFACE OFFSET:-

• Used to offset the surface to a certain distance in bothe direction

RULED SURFACE:-

• ruled surface is build by selecting the edges of the surface and guided by the face ,sketch or plane

KNIT SURFACE:-

• Knit surface is a tool used to merge and fill the gap beatween intersectin surfaces.

6-MIDDLE SEAT:-

• middle seat build on the centre of the yacth

Commands used to designed the middle seat

• sketch
• boss extrude
• cut extrude
• champer
• fillet
• mirror

7-FRONT SEAT:-

• build at the front side of the super structure

command used to design the front seat:-

• skecth
• sweep surface
• surface trim
• surface extrude
• surface knitt
• surface loft
• revolve
• champer
• fillet
• Dome
• Mirror

8-SUPER STRUCTURE:-

• Is nothing but a deck which is constucted on the hull surface,where the pilot cabine and other interior part are build.

Commands used to design the superstructure:-

• sketch
• surface extrude
• Ruled surface
• surface sweep
• Knit surface
• Cut extrude
• Loft surface
• extrude thin
• Champer
• Fillet
• Mirror
• Combine
• Sweep
• Thicken surface
• Dome

9-PROPELLER:-

• is fan type mechanisum used to move the ship forward by trasmitting rotational motion in to the thrust.

Commands used to design the proppeler :-

• sketch
• revolve
• lofted surafce
• cut extrude
• fillet
• Circular pattern

Commands used to design the proppeler:-

• sketch
• revolve
• lofetd surface
• cut extrude fillet
• circuler pattern

10-ASSEMBLY OF YACTH:-

• All the modelled parts are inserted one by one in the assembly.
• Since all the parts plane will make coicident with rhw yacth.

isometric view:-

2-front view:-

3-back view:-

4-top view

5-camera setup view:-

visualise imges:-

CONCLUSION:-

• The parts of the yacth are modeled.
• the parts are inserted in the assemble invironment and the yact is assemble using the solidwork 2019 software.
• The photorealistic image are rendered using the solidwork visualise.

OUTCOMES:-

• Learn how to use the surface and create solid parts and assemble the parts.