Week 10 - Challenge 2- Attachment Feature Creation (Dog House)

Objective: Case 1: To extract mid surface for the tube model and provide a connection with sharing options at the tube joint locations. Case 2: Create a model in space claim as per the dimensions provided and run a free free modal analysis for the model and record the results. Software Used: Ansys Student Version 2024…

Title of the Project:                                 Box Assembly using NX CAD Objective: To design and prepare a detailed report of a box assembly using NX Sheet metal…

Objective: Design the inner and outer panel of the car backdoor using class A surface as reference. Tools used: NX CAD 12.0 Introduction: The backdoor of a car is the rearmost part of the vehicle which gives access to the trunk space of the vehicle. The rear door also supports the reinforcements and added weights of the…

  Objective:   ·         Design a Car roof with reinforcements as per master sections and thicken part. Create emboss and cutouts to enhance part stability. Carry on draft analysis and check the draft feasibility.   ·        …

Objective: Design a plastic component of a front door assembly using class A surface provided. Design B side features using master sections and foolowing design guidelines. Plastic components of a front door panel Lower substrate Map pocket Bottle holder Arm rest We will bedesigning the plastic components of the above…

  Objective: Design a front fender using provided skin data and master section and develop part incorporating fixing techniques. Fender: A car tire fender is a plastic, metal, or rubber panel that bends over the wheel on the side of the car, extending from the front bumper to the car door. The main function of car fenders…

Objective: Analyze section inertia of a hood designed using UG NX cad software and calculate the section modulus of a hood. Study of variation of section modulus varying hood geometry and improvise the section modulus. Section modulus: Section modulus is a geometric property for a given cross section used in the design…

Objective: To study and write a detailed project report on design and construction of 18 kWh ANR 26650 cells. Overview: Lithium Werks’ 26650 cells are capable of delivering very high power due to its use of patented Nanophosphate ® battery technology. Based on lithium iron phosphate chemistry (LiFePO4 ), the…

Objective: We have a BMS battery simulink model and simulate the model and prepare a detailed report on model and results. Problem Statement: https://in.mathworks.com/matlabcentral/fileexchange/72865-design-and-test-lithium-ion-battery-management-algorithms We use the above link to download the simulink model for preparing…

Objective: Study of different materials and chemical reactions occurring at the anode and cathode of LCO, LMO, NCA, NMC LFP and LTO type of lithium ion cells. Tabulate the difference between each type of lithium ion batteries based on their characteristics Theoretical study: Lithium ion Battery: Lithium (Li0 is the third…

Objective: Development of forward energy based fuel consumption model of a P1 architecture Hybrid vehicle. We have an initial data of a Honda insight motor and battery. And these data is taken from Advisor model developed by NREL, USA. Based on the initial data and details provided we need to model a P1 Hybrid architecture…

Table of contents Objective of study Problem statement Theoretical study       3.1 Types of propulsion Models       3.2 Conventional or IC Engines       3.3 Forward Based Conventional Vehicle Model Formulae used for computation and modelling Project Overview            …

 Objective: To carry out system level simulation for All terrain Vehicles of BAJA ATV with continuously varying transmission. Model study: We have a BAJA ATV with CVT Simulink model having different blocks and it is controlled by acceleration throttle and brake which are given as input. The complete project has three…

Challenge4_1: Objective: To implement a Simulink model for washing machine control with corresponding  cycles using state flow. Solution Procedure: Using chart option we create a state flow with following conditions. Check power ON/ OFF. Check the water supply if water supply is OFF indicate using lamp. First 200…

Challenge 2.1 Objective: To Build a Simulink model for doorbell with following condition. Switch operating the doorbell with 2 seconds switch closed and open. Uses electromagnetic solenoid valve. Solution procedure: We have electromagnetic solenoid valve which rings the bell as switch opens and closes at every 2 seconds.…

Objective: Write a matlab program for solving second order ODE for a simple pendulum using                             After solving the second order ODE plot a graph for angular velocity and angular displacement against time varying from 0 to 20 seconds…

Objective: Write a program in Matlab that plots the 2R robotic arm at various angles. Stitch the plots to animate a movie the robotic arm to animate the working. Problem Statement: We have a two links of a robotic arm with defined lenght and we need to plot the arm on the graph to find the reachability of arm at different…

01. popt refers to optimizing parameters defined in an equations and these variables will be obtained using curve_fit function        pcov refers to co-variance matrix for the above popt values 02. np.array(temperature) will pass the complete array of temperature values into the functions…

Objective: Write a python program for solving second order ODE for a simple pendulum using                             After solving the second order ODE plot a graph for angular velocity and angular displacement against time varying from 0 to 20 seconds…

Objective: 1. write and execute a python code that calculates and plot a P-V diagram for otto cycle. 2. Calculating thermal efficiency of otto cycle in the end using calculated temperature parameters and print the output.   Problem Statement: We have a otto cycle with following geometric dimensions and inputs.  …

01.  The Major elements in the above automotive wiring diagram Battery Generator Distributor Fuse Ammeter Current and Voltage regulator Switches   02.  a. Fuse          Purpose: Fuse is used as safety device in a circuit to protect the device   Working : when ever there…