For assembly a product first we have to create the individual parts of the product as per the given parameters. Create the parts with the help of sketcher and part workbench with proper Iso constrained and perform Boolean operation if required Then open a new assembly workbench Import the created parts into…
Gokul K
updated on 11 Feb 2023
Project Details
Leave a comment
Thanks for choosing to leave a comment. Please keep in mind that all the comments are moderated as per our comment policy, and your email will not be published for privacy reasons. Please leave a personal & meaningful conversation.
Other comments...
Read more Projects by Gokul K (21)
Week 14 challenge
AIM To assemble the butterfly valve and apply the GD&T for the assembly PROCEDURE First import the all required parts in assembly workbench then give the required constrains to the parts the assembly is get finsihed then…
04 Jun 2023 06:24 AM IST
Design of backdoor
AIM To Design an car back door and reincforcement from the given outer pannel Back door The back door is a hinged door/tailgate at the rear of the vehicle. It may be used for loading and unloading cargo, or to get passengers in and out, in case there are seats present at…
16 May 2023 08:25 AM IST
Roof Design
AIM To create the roof assembly and develop the required flanges from the given styling surface and follow the master section ROOF An automobile roof or car top is the portion of an automobile that sits above the passenger compartment, protecting the vehicle occupants from sun, wind, rain, and…
17 Apr 2023 06:21 AM IST
Fender Design - Wheel Arch Challenge
AIM To calculate the wheel arch clearance from the required points and it for europen standard WHEEL ARCH The wheel arch is the semicircular part positioned above the wheel of a vehicle. The most important body change was that the front wheel arch was cut higher…
06 Apr 2023 08:17 AM IST
Section Modulus calculation and optimization
SECTION MODULUS It is the ratio between moment of inertia of the beam cross section about the neutral to the distance of extreme fiber from the neutral axis Section modulus is a geometric property for a given cross-section used in the design of beams or flexural members S = I/Y Where I = moment…
28 Mar 2023 06:13 AM IST
Hood design-Week 2
Hood A car hood is an part which is used to cover and protect the engine it also called as bonnet The common material used for manufacturing the hoods are steel,aluminium,fiberglass and carbon fiber THE DESIGN CONSIDERATION FOR HOOD ARE Safety…
26 Mar 2023 05:59 AM IST
Underbody Coating
UNDER BODY COATING: Under body coating is an process which is used to prevent the corrosion of an automobile under body material. the coating will be applied uniformly. …
11 Mar 2023 04:59 AM IST
Benchmarking
BENCH MARKING: Bench marking is the process of comparison between similar products available in market it includes performance,quality,consumer feedback etc BENCH MARKING FOR AVALIABLE CARS IN MARKET CASE: …
10 Mar 2023 05:58 AM IST
Week 9 - Project_1 - Door Trim Lower with Engineering Features
AIM : To create a door trim plastic component with the given A surface and attachements of heat stakes and locators PROCEDURE: First create a tooling axis with the reference of A surface Then create a B surface by offseting the…
08 Mar 2023 09:36 AM IST
Week 11 - Final project
AIM: To create door trim side panel as a complete product PROCEDURE: First to create B surface individual the components required for the door trim pannel with the help of A surface and master section Before creating B surface create a tooling axis for each component After compeleting the B surface make…
07 Mar 2023 06:05 AM IST
Week 9 - Project - A pillar Design with Master Section
AIM: To create A pillar with the help of master section PROCEDURE: first create the tooling axis with the help of master section for creating the B surface offset the given A surface as per the master section then you will get the B surface…
19 Feb 2023 11:51 AM IST
Week 8 - Challenge 5 - Door Trim Lower
REPORT : first create the tooling line from the given A surface create the B surface by offseting A surface you will get the B surface …
19 Feb 2023 11:48 AM IST
Week 10- Assembly Workbench
For assembly a product first we have to create the individual parts of the product as per the given parameters. Create the parts with the help of sketcher and part workbench with proper Iso constrained and perform Boolean operation if required Then open a new assembly workbench Import the created parts into…
11 Feb 2023 11:33 AM IST
Week 9 - Attachment Feature Creation - Challenge 2
AIM: To attachement feature (dog house) on the given door trim PROCEDURE: To perform the attachement feature opertation first we have to create b surface. for creating the b surface we should offset the class A surface for the given…
03 Feb 2023 05:38 AM IST
Week 9 - Attachment Feature Creation (Ribs & Screw Boss) - Challenge 1
AIM: To create ribs and screw boss procedure: create a solid body from the class A surface for a thickness of 2.5mm Now select the positioned sketch and give the reference surface from the component Then draw the sketches for the ribs snd…
26 Jan 2023 05:28 AM IST
Week 8 - Challenge 6 - Core & Cavity Design
AIM: To create a core and cavity block for an switch bazel PROCEDURE: For creating the core and cavity block of an component. First we have to identify the identify core side and cavity side of the component The A surface is the core side and the B surface is the cavity side,Then Create a parting surface on B surface…
24 Jan 2023 04:39 AM IST
Week 8 - Challenge 4 - Bumper
AIM: To create & draft analysis a bumper from the given class A surface. STEPS: first we should create the tooling axis from the class A surface. after created the tooling axis.then offset the class A surface…
17 Jan 2023 11:12 AM IST
Week 8 - Challenge 3 - Coin Holder Design
REPORT : To create an coin holder design first we have to create an tooling axis with the help of class A surace. consider the suitable direction for creating the componet from that…
06 Jan 2023 04:09 AM IST
Week 8 - Challenge 1 - Base Bracket Design
REPORT For creating the tooling axis. first we should identify the suitable tooling direction for making the component by intersecting the plane yz and class A surface we get an sketch as output in that sketch draw a line on both side on the drafted line as shown in…
28 Dec 2022 01:10 PM IST