Week 1- Mixing Tee

AIM:  to simulate the flow through a cyclone separator and showing the results for the different particle size and for the different velocities. we have to run the simulation for the six cases   1).set the velocity constant to 3 m/s and do simulation for the varying size of the particle. 2).set the particle…

AIM: Perform a combustion simulation on the combustor model and plot the variation of the mass fraction of the different species in the simulation using line probes at different locations of the combustor as shown in Fig. You need to plot for CO2, H2O, CH4, N2, O2, NOx emissions & Soot formation.  As you must…

Objective: Perform parametric study on gate valve by setting the opening from 10% to 80% Obtain the mass flow rates at the outlet for each design point. Calculate the flow coefficient and flow factor for each opening and plot the graph. Discuss the results of the mass flow rate and flow coefficient Gate valve: A gate valve,…

Objectives: some practical CFD models that have been based on the mathematical analysis of Rayleigh Taylor waves explain how these mathematical models have been adapted for CFD calculations. Perform the Rayleigh Taylor instability simulation for 2 different mesh sizes with the base mesh being 0.5 mm. Compare the results…

AIM:  to simulate the conjugate heat transfer on the graphics card and show the results of wall haet transfer  co efficient and the contoursa of the heat flow inside the enclosure(domain).  given conditions are velocity inside the enclose is between the 1-5 m/s. have to give results for the 3  simulation…

  AIM: To perform Conjugate Heat Transfer (CHT) Analysis with Exhaust Port Simulation. Introduction      #conduction:       conduction is the process of the heat transfer taken place with the same medium. it mainly happens in the soluids. or we can call it as the heat transfer…

AIM: to simulate the flow of the air through the Ahmed body and providing the correct results  describing the importance of the Ahmed body explaining the negative pressure in the wake region      DESCRIBING THE IMPORTANCE OF THE AHMED BODY:     Ahmed Body and Its Importance:- Ahmed…

AIM : to simulate the flow over the cylinder by using the steady-state solver and unsteady state solver and explaining the phenomenon of  Karman vortex shedding. part1 : to simulate the flow using the steady-state and unsteady state solver.      introduction to the flow over a cylinder: 2. Unsteady…

   Objective To simulate the flow of air through mixing tee and understand the effect of length of pipe and momentum ratio of velocity for mixing of air by using two different types of pipe i.e. short pipe and long pipe. About In industrial process engineering, mixing is a unit operation that…

AIM :  TO SIMULATE THE WEDGE FLOW USING THE OPEN FOAM FOR DIFFERENT ANGLES OF WEDGE AND TO CAPTURE THE RESULTS  THAT.  THE GIVEN ANGLES FOR THE FLOW ARE         10        25        45    simulation flow through a pipe from open foam…

simulation flow through a pipr from open foam objective: the  main objective of the project is to simulate the flow through the pipe in OPEN FOAM software.   we have to write the program fro the generation of the blockmeshdict file, or computational mesh for wedge angle and grading scheme. calculate the length…

DIFFERENCE BETWEEN FDM AND FDM   2. Differences between Finite Volume Method and Finite Difference Method     Finite Volume Method (FVM)  Finite Difference Method (FDM) 1. Grid Generation Domain is divided into control volumes or cells with variable of interest located at the centroid of each control…

AIM:  to simulate an incompressible-laminar-viscous flow through the backward facing step geometry.  and we have to perform grading factor test and  also we have to capture the results how the flow is going to change if we change some of the parameters   OBJECTIVES OF THE PROJECT: Specify the boundary…

    Flow-Through Nozzle Introduction to Nozzle A nozzle is a device designed to control the direction or characteristics of a fluid flow (to increase velocity) as it exits (or enters) an enclosed chamber or pipe. A nozzle is often a pipe or tube of varying cross-sectional area, and it can be used to direct or…

THIS IS FOR THE STEADY STATE METHOD IN WHICH WE ARE SOLVING THREE METHOD THAT IS JACOBI METHOD, GAUSS SEIDEL METHOD, SUCCESSIVE OVER RELAXATION  OBJECTIVE: to solve 2D heat conduction equation by using the point iterative techniques. The Boundary conditions for the problem are as follows; Top Boundary = 600 K Bottom…

OBJECTIVE: to calculate the tailor series method for the skewed right approximation, skewed left approximation, and central differencing writing the program to calculate the errors in the right-skewed scheme, left-skewed scheme, central differencing scheme     EQUATIONS AND THEORY: before going to calculation…

OBJECTIVE :  TO Create a Rankine Cycle Simulator MATLAB. MY code calculate the state points of the Rankine Cycle (any type of your choice) based on user inputs.  WORKING OF THE RANKINE CYCLE:   **** THE NOTATIONS USED IN THE DIAGRAM AND THE H-S DIAGRAM ARE DIFFERENT FROM EACH OTHER I AM USING DIFFERENT CYCLE…

AIM: to extract the coefficients from the following file and i.e thermo.dat and creating the program to calculate the specific heat, enthalpy, entropy. and to calculate the molecular weight of each species. and plotting the graph for the (temperature) versus enthalpy, entropy, specific heat. and w are finding the local…

OBJECTIVE:             Write a code in MATLAB to optimise the stalagmite function and find the global maxima of the function. EXPLANATIONS: Clearly expalin the concept of genetic algorithm in your own words and also explain the syntax for ga in MATLAB in your report.  …

  OBJECTIVE:  To describe the transient behavior of a system i.e simp pendulum.  objective is to write a program that solves the following ODE. This ODE represents the equation of motion of a simple pendulum with damping. EQUATION: `(d^2(theta))/dt+b/m(d(theta))/dt+g/l*sintheta=0``   by breaking down…