Problem set 2 -week 3 challenge : Anti-Characteristics

From the ANR26650M1-B cell Data Sheet specifications following observations made:- Assumptions : Energy ( capacity )     = 18 Kwh Voltage required to run system = 300 V From Specification Data Cell Nominal voltage  = 3.3 V Capacity = 2.5 A Weight of cell = 76gms  1) Cell in Series = voltage…

OBJECTIVE 1 Battery Management system How to Open ? After Opening the below link, Click download for Battery Management system Zip file as shown in image https://in.mathworks.com/matlabcentral/fileexchange/72865-design-and-test-lithium-ion-battery-management-algorithms Go to Matlab open the Battery Model Project from saved…

1. Lithium Battery Lithium batteries rely on lithium ions to store energy by creating an electrical potential difference between the negative and positive poles of the battery. An insulating layer called a “separator” divides the two sides of the battery and blocks the electrons while still allowing…

1.  Major Elements          a) Batttery          b) Starter          c) Ammeter          d) Fuse          e) Generator          f) Foot selection switch    …

1. Attched pdf file for the Formaulas used for Calculation 2. Calculations for Roll Gradient analysis and Understeer Budget is in Enxcel file attached

1. For Calculation please see the attached pdf file 2. For Plot of Passenger car see output below         OUTPUT:-         1. Step Response                            2. Sin response for 5deg and 7 Hz    …

Please see the hand calculation in attached file 

1.Manual calculation attached as pdf 2.Calculation done in Excel file, we can modify the Given values in Excel to get desired output

1. Manual calculations done attached as pdf file 2. Calculations done on Excel file , we can modify given values to get the desired output. 

AIM:- To setup and analyse Geneva drive Mechanism THEORY:- Introduction:- Geneva Drive is a gear mechanism that translates rotation motion into intermittent rotary motion. The rotating drive wheel has a pin that enters into the slot of driven wheel and make it rotate step by step. The driving wheel has also an elevated…

AIM :- To perform a study on Stress and Strain on Flex FLCA body by replacing the Rigid LCA body in the Front axle, keeping the input provided.   CREATION OF FRONT AXLE (INBUILT) Step 1 :-  Go to the option Model à Assembly Wizard pop will show and select according to the image shown below.   CREATION…

AIM:- To setup a 3D contact between CAM and Follower and plot the displacement in Y direction   THEORY In MotionSolve the contact collision algorithm searches for proximity between geometries when any penetration between the two sets of geometries occurs, a force based on the defined contact properties is generated.…

AIM :- To avoid trunk lid hitting the Trunk body using model.   CREATION OF MODEL Lets create Cylinder Models using Points with Parametrization Step 1 :- Start the Hyperworks and change the list to motion View   Step 2 :- Create a Bodies Follower, Coupler and Input as shown in image below   Step 3 :- Create…

Aim :- To Create a simple mechanism with help of inputs given and gravity in Y axis.   CREATION OF BODY Step 1 :- Start the Hyperworks and change the list to motion View Step 2 :- Create a Body_1 & Body_2 by selecting the option shown in image below Step 3:- Change the properties for Body_1 & Body_2 for inertia…

Aim :- To Create and plot a free falling body having mass of 1 Kg and gravity in Y axis.  Question - 1 Simulation Construction :- Step 1 :- Start the Hyperworks and change the list to motion View                         Step 2 :- Create a Free body by selecting…

Aim:- To model IC Engine valve parts and assemble to do motion analysis for 2 cases of CAM design. Introduction on IC Engine Valve Assembly:- IC Engine Valve assembly is one of the major component in Engine assembly. It consists of 5 parts Cam Push Rod Rocker arm Engine valve Engine valve Mount Cam:- In this assembly we…

Aim: - To model and assemble the Piston parts and to do motion analysis for 3 cases.  Introduction on Piston Assembly:-  Piston assembly is one of the major component in Engine assembly. It consists of 5 parts Piston Head Wrist pin Connecting Rod Crank Piston Head:- This component is located in Engine cylinder…

Introduction An planetary gearset (also known as a epicyclic gear train) consists of two gears mounted so that the center of one gear revolves around the center of the other. A carrier connects the centers of the two gears and rotates to carry one gear, called the planet gear or planet pinion,…

Step:1  Geneva Driver and Geneva Driven parts are created in Part mode with changing dimensioning system to MMGS Step:2 a) Open new assembly and insert the Geneva Driver and Driven parts. b) Right click on Geneva Driven part and change to float prefernce so that part can move. Now we have to constraint the models c) Show…