Menu

Executive Programs

Workshops

Projects

Blogs

Careers

Student Reviews



More

Academic Training

Informative Articles

Find Jobs

We are Hiring!


All Courses

Choose a category

Loading...

All Courses

All Courses

logo

REPRESENTING A GIVEN FUNCTION USING SIMULINK AND TO UNDERSTAND PRE-BULT MATLAB SIMULATION BLOCK OF SUSPENSION SYSTEM COMPARISION.

AIM : To plot the given function using "SIMULINK" and to understand the pre build matlab simulation block of "SUSPENSION SYSTEM COMPARISION". OBJECTIVE : 1. To plot this function  yx=(x-1)*(x-3)^2*(x-9)^2 using basic Simulink blocks.  2. To determine the similarities and differences between the three…

Project Details

Loading...

Leave a comment

Thanks for choosing to leave a comment. Please keep in mind that all the comments are moderated as per our comment policy, and your email will not be published for privacy reasons. Please leave a personal & meaningful conversation.

Please  login to add a comment

Other comments...

No comments yet!
Be the first to add a comment

Read more Projects by Suchith Bengaluru suresh (23)

Week 6-Meshing of Hood Challenge

Objective:

AIM:  To Mesh the given "HOOD MODEL" by satisfying the given quality criteria and with a target element size of "5mm".   OBJECTIVE: To Follow the mentioned quality criteria, mesh the component given with a target element size of "5mm" and assign thickness:   PROCEDURE:   STEP-1: EXTRACTING MID SURFACE FOR THE GIVEN COMPONENTS:…

calendar

13 Mar 2021 11:34 AM IST

    Read more

    Week 4-1D Element Creation Challenge

    Objective:

    AIM: To Mesh the Given component with the Size of 5 Units. Create 1D elements on the following component with given cross-section and DOF. a. Rod element:- Translational DOF should be Constrained with RBE2 link. Cross-Section: BOX- Dimension a= 12 mm                  …

    calendar

    13 Mar 2021 10:48 AM IST

      Read more

      Week 12:Project 2-Meshing of Rear Wheel Holder challenge

      Objective:

      AIM:   To Mesh the given "REAR WHEEL HOLDER MODEL" by satisfying the given quality criteria and with a target element size of "5mm".   OBJECTIVE: To Follow the mentioned quality criteria, mesh the component given with a target element size of "5mm" and assign thickness:   PROCEDURE:   STEP-1: EXTRACTING MID SURFACE FOR…

      calendar

      12 Mar 2021 01:30 PM IST

        Read more

        Week 12:Project-1-Meshing of Door Inner Panel Challenge

        Objective:

        AIM:   To Mesh the given "DOOR INNER PANEL MODEL" by satisfying the given quality criteria and with a target element size of "4mm".   OBJECTIVE: To Follow the mentioned quality criteria, mesh the component given with a target element size of "4mm" and assign thickness:   PROCEDURE:   STEP-1: EXTRACTING MID SURFACE FOR…

        calendar

        12 Mar 2021 01:27 PM IST

          Read more

          Week 9-Creation of 1D Connectors Challenge

          Objective:

          AIM:    To Mesh the given component with the given "Element quality criteria" and to connect all the different components with appropriate "1D connectors" according to the above-specified places and specified connectors.    OBJECTIVE:   Target Element size - 5 Units S.N Quality Criteria  Value …

          calendar

          12 Mar 2021 01:22 PM IST

            Read more

            Week 8-3D Tetra Meshing Challenge

            Objective:

            AIM:    To do "Tetramesh" on the above given 3 components using given appropriate criteria    OBJECTIVE: 1. To Create a Teramesh for Housing component with the following quality criteria. Elements sizes: Min- 2 Units, Target- 5 Units, Max- 7 Units  Tet collapse: 0.15 2. For the given model 2, To Create a 3D Tetramesh with…

            calendar

            12 Mar 2021 01:20 PM IST

              Read more

              Assignment 7

              Objective:

              AIM: To do "SIDE CRASH ANALYSIS" for the given "Neon side crash -BIW" car model using "HYPERMESH AND HYPERCRASH".   OBJECTIVE: Neon side crash -BIW To Check unit system and either follow [Mg mm s] or [Kg mm ms]. To Create appropriate interface ,friction 0.2 and recommended parameters. To Make sure of no penetration and…

              calendar

              29 Dec 2020 07:22 AM IST

                Read more

                Assignment 6

                Objective:

                AIM: To do "FRONTAL CRASH ANALYSIS" for the given "BIW" car model using "HYPERMESH AND HYPERCRASH".   OBJECTIVE: FRONTAL CRASH BIW: To Check unit system and either follow[Mg mm s] or [Kg mm ms]. To Create appropriate interface ,friction 0.2 and recommended parameters. To Make sure of no penetrations and intersection. To…

                calendar

                29 Dec 2020 07:21 AM IST

                  Read more

                  Assignment 5

                  Objective:

                  AIM: To do "MESHING" on the given "BUMPER ASSEMBLY" with mesh size of "6mm" and To run the given "CRASH TUBE MODEL" according to the given data through 6 different cases.   OBJECTIVE: Create the mesh for bumper assembly,mesh size should be 6mm.  Run the crash tube model as it is. Change the Inacti=6 and run.…

                  calendar

                  07 Dec 2020 09:04 AM IST

                    Read more

                    Assignment 4

                    Objective:

                    AIM: To run the simulations for 7 different cases for "RUPTURE PLATE", provided with appropriate given data.     OBJECTIVE: Compare all the 7 different cases according to:  Total number of cycles, Energy error, mass error and simulation time. Notice the animation of all 7 and describe the animations in brief…

                    calendar

                    01 Dec 2020 07:28 AM IST

                      Read more

                      Assignment 3

                      Objective:

                      AIM:  1) To run the simulations on the given "Crash Beam" file with "Run Time" as "55 milli seconds" and "Number Of Animation Steps" as "50". 2) This Simulation should be first done by "Without modifying any Element properties" and the second simulation by "Changing all the element properties which are provided".   OBJECTIVE:…

                      calendar

                      23 Nov 2020 08:54 AM IST

                        Read more

                        Assignment 2

                        Objective:

                        Q1. When we open the "Starter file : FIRST_RUN_0000", we can get to see  properties of a material as shown below,               Young's Modulus of Steel : 210000 g/mm-ms^2 Density of Steel : 0.0078 g/mm^3 We know that "Speed Of Sound" = `sqrt(E/rho)` = `sqrt(210000/0.0078)` = 5188.74 mm/ms So the speed of sound is 5188.74…

                        calendar

                        17 Nov 2020 12:12 PM IST

                          Read more

                          Assignment 1

                          Objective:

                          AIM:  To carry out Geometry clean up, Extract mid surface and to do 2D meshing on mid surface of the following given Components: 1) Practice component. 2) Clip repair component. 3) Mounting Bracket.   OBJECTIVE: To, 1) Clean the geometry. 2) Extract midsurface. 3) Clean midsurface geometry. 4) Ignore holes less than dia…

                          calendar

                          17 Nov 2020 12:12 PM IST

                            Read more

                            WIDE OPEN THROTTLE

                            Objective:

                            1.   What is the ratio of hill climbing power required by fully loaded tata ultra truck to the half loaded one?   SPECIFICATIONS FOR TATA ULTRA TRUCK 1518:   HILL CLIMBING FORCE OF FULLY LOADED TATA TRUCK 1518: Curb weight (or) Front axil weight = 5510kg Pay load (or) Rear axil weight = 10200kg Gross…

                            calendar

                            13 Mar 2020 01:29 AM IST

                              Read more

                              TO CREATE MODEL OF DOOR BELL USING SOLENOID AND TO CREATE MODEL OF THERMISTOR TO SENSE THE TEMPERATURE OF A HEATER ACCORDING TO THE GIVEN PARAMETERS

                              Objective:

                              Q1). Make a Simulink model of Doorbell using solenoid block. AIM:  To create a simulink model of the doorbell according to the given conditions. THEORY: The doorbell is created using inbulit blocks in simulink such as solenoid and plunger block. solenoid is connected to a poer source of DC voltage supply, here…

                              calendar

                              28 Feb 2020 04:33 AM IST

                                Read more

                                REPRESENTING A GIVEN FUNCTION USING SIMULINK AND TO UNDERSTAND PRE-BULT MATLAB SIMULATION BLOCK OF SUSPENSION SYSTEM COMPARISION.

                                Objective:

                                AIM : To plot the given function using "SIMULINK" and to understand the pre build matlab simulation block of "SUSPENSION SYSTEM COMPARISION". OBJECTIVE : 1. To plot this function  yx=(x-1)*(x-3)^2*(x-9)^2 using basic Simulink blocks.  2. To determine the similarities and differences between the three…

                                calendar

                                26 Feb 2020 01:26 AM IST

                                • MATLAB
                                Read more

                                PARSING OF NASA'S THERMODYNAMIC DATA USING MATLAB

                                Objective:

                                AIM:  To parse the NASA thermodynamic data file and then calculate thermodynamic properties of various gas species.   OBJECTIVE: 1. To Calculate the molecular weight of each species. 2. To Plot the Cp, Enthalpy and Entropy for the local temperature range specific for each species. 3. To Save the…

                                calendar

                                23 Feb 2020 10:55 AM IST

                                  Read more

                                  TO FIND GLOBAL MAXIMA USING GENETIC ALGORITHM

                                  Objective:

                                  AIM: To determine "GLOBAL MAXIMA" of a "STALAGMITE FUNCTION" using "GENETIC ALGORITHM" in MATLAB OBJECTIVE:  1. To determine global maxima by optimizing stalgamite function using genetic algorithm. 2. To understand "GENETIC ALGORITHM" THEORY: A Genetic algorithm is inspired by Charles Darwin’s theory of…

                                  calendar

                                  19 Feb 2020 10:19 AM IST

                                  Read more

                                  CURVE FITTING FOR LINEAR AND CUBIC POLYNOMIAL FOR GIVEN DATA USING MATLAB

                                  Objective:

                                  AIM: To execute a program to curve fit for both linear and cubic polynomial for the given cp data using MATLAB. OBJECTIVE:  1. To Write code to fit a linear and cubic polynomial for the Cp data. 2. To Plot the linear and cubic fit curves along with the raw data points.  3.  To explain the parameters…

                                  calendar

                                  17 Feb 2020 09:21 AM IST

                                  Read more

                                  SIMULATION OF A SIMPLE PENDULUM BY SOLVING 2ND ORDER DIFFERENTIAL EQUATION USING MATLAB

                                  Objective:

                                  AIM: To simulate the transient behaviour of a simple pendulum and to animate the oscillation using MATLAB. OBJECTIVE:  1. To execute the program using 2nd order differential equation for calculating displacement and velocity with respect to time in MATLAB. 2. To animate the oscillation of a simple pendulum 3.…

                                  calendar

                                  13 Feb 2020 10:26 AM IST

                                  Read more

                                  CALCULATION OF THERMAL EFFICIENCY AND PLOTTING PRESSURE V/S VOLUME OF OTTO CYCLE USING MATLAB

                                  Objective:

                                  AIM: To determine the thermal efficiency and to plot pressure v/s volume of an Otto cycle. OBJECTIVE: To execute program for simulating an air standard cycle or Otto cycle using MATLAB. THEORY: The Otto cycle is a cycle of engine operation which requires four strokes of the piston for induction,…

                                  calendar

                                  12 Feb 2020 09:22 AM IST

                                  Read more

                                  SIMULATION OF A FOWARD KINEMATICS OF A ROBOTIC ARM

                                  Objective:

                                  FOWARD KINEMATICS OF A 2R ROBOTIC ARM AIM: Smulation on foward kinematics of a 2R robotic arm and To determine the workspace of a foward kinematic 2R robotic arm using MATLAB. OBJECTIVE: To execute a Program for solving the forward kinematics of a 2R robotic arm manipulator           THEORY:…

                                  calendar

                                  11 Feb 2020 10:04 AM IST

                                  Read more

                                  CALCULATING DRAG FORCE OF A MOVING OBJECT USING MATLAB

                                  Objective:

                                  CALCULATING DRAG FORCE FOR FLOW OVER BICYCLE AIM: To calculate drag force. OBJECTIVE:  1. To execute a program for plotting velocity v/s dragforce. 2. To execute a program to plotting co-efficient of drag v/s dragforce. FORMULE: `Fd = 1/2 .rho.A.V^2.Cd` Where, Fd = Drag force, (N) A = Frontal area of the moving object,…

                                  calendar

                                  11 Feb 2020 02:59 AM IST

                                    Read more
                                    Showing 1 of 23 projects