MESHING OF A BOTTLE CAP MODEL USING ANSA

AIMWe are currently working on developing code for the air standard Otto cycle to extract the pressure versus volume diagram and calculate the thermal efficiency of the cycle.The ideal Otto cycle is a thermodynamic cycle that describes how a spark-ignition internal combustion engine works. It consists of four…

Aim:demonstrate spherical, revolute, cylindrical, and translational joints between two rigid bodies and two deformable bodies. 2. Revolute jointTwo pairs of nodes are created for constraining, using Node edit option under Element Tools. The nodes 101, 102 are constrained to part 1 and 103,104 to part 2 respectively, using…

Objective:The aim of this study is to calculate the Mooney Rivlin and Ogden material constants and compare them using stress-strain data obtained from a Dogbone specimen tensile test with 100 percent strain.Background:Hyperelastic materials are defined as materials that can undergo more than 100% strain without experiencing…

OBJECTIVE In this challenge we have to perform a simulation of crash box it similar to car carsh. but, here instead of car and their element there is box like structure. Here are the information about challenge - The crashbox should crash into a rigidwall created using *RIGIDWALL_ keyword. Check the manual to understand…

OBJECTIVE       To perform tensile test on a ogden material cubic block to calculate stretch ratio  for different element formulation and to plot the stress vs stretch ratio plot and Compare the results for the simulation using ELFORM = 1, 2, -1, -2.   PROCEDURE Create a block of 10mmx10mmx10mm dimension…

Objective       The objective of this challenge is to convert the given SI unit values of the given quantities to gm/mm/ms units and also to prepare consistent unit system table for different unit system. Value of the following measurements are given as follows: 1.MASS 1kg2.LENGTH 1m3.TIME 1s4.FORCE 1N5.STRESS…

OBJECTIVE Modelling the beam and Solid spottweld for the plates and crash test  result of  axial and shear force should be compared among beam and solid elements. CAD MODEL The Cad Model Contains Two Parts Such As Uppar Part And Lower Part. They Are Not Connected Each Other In This Challenge We used Connect…

SURFACE MODELING OF YACHT Objective: The objective of this project is used to create a surface model of different parts of the yatch using solidworks. To assemble the different parts modeled for the yatch. part modeling: part modeling you can create a part from a conceptual  sketch through solid feature based modeling.as…

EXTRACTING MID SURFACE 2D MESHING OF A IP SUBSTRATE USING ANSA OBJECTIVE To create 2D mesh for  IP substrate  component with given element quality criteria and to assign midsurface thickness to the shell element using ansa.     METHODOLOGY: GEOMETRY CLEAN UP MIDSURFACE EXTRACTION MESHING AS PER CRITERIA…

AMERICAN CHOPPER  objective: The objective of this project is used to creat a model of different parts of the chopper using solidworks. To assemble  the different parts modeled for the chopper. To create a photorealistic model of the chopper and render the model using solidworks visualize.   Part…

OBJECTIVE Run a drop test simulation on a mobile phone by using LS dyna software and conclude the result.   MODEL We have the keyword file containing elements and nodes. Import the keyword file in the ls prepost.   PROCEDURE FOR RUNNING A SIMULATION In the model we have three parts as phone, Rigid wall and Top…

OBJECTIVE To perform a tetra mesh for Rear suspension model under specified quality criteria. METHODOLOGY: geometry clean up assigning PID Meshing as per quality criteria creating volumetric mesh creating appropriate connection GEOMETRY CLEANUP. open the rear suspension model.ansa file set the perimeter length and…

HOOD MESHING FOR STRUCTURAL ANALYSIS USING ANSA The objective of this project is to perform meshing for a given hood model using ansa.the model is cleaned and checked for errors,then using the given element size is meshed accordingly. For meshing process ,the following steps are necessary Geometry checks assign pid for…

 CCB ASSEMBLY MODELING USING APPROPRIATE CONNECTION  objective To create 2D mesh for component of cross car beam model with given element quality criteria. Assemble the CCB by using appropriate connections.   METHODOLOGY: GEOMETRY CLEAN UP MIDSURFACE EXTRACTION MESHING AS PER CRITERIA ASSIGNING CONNECTIONS…

    MESHING OF A BOTTLE CAP MODEL USING ANSA objective To create 2D mesh for a bottle cap model with given element quality criteria and to assign midsurface thickness to the shell element using ansa METHODOLOGY: GEOMETRY CLEAN UP MIDSURFACE EXTRACTION MESHING AS PER CRITERIA ASSIGNING THICKNESS PROPERTY QUALITY…