1. The major elements of the above automotive wiring diagram are STARTER, BATTERY, BREAKER, DISTRIBUTOR, GENERATOR 2. The three elements are :                                1. Battery                …

 1.  Given range = -17.3:0.1:0.9        Step-1: Firstly save the given excel file with an extension of '.m'        Step-2: Import the data from the excel sheet to the workspace  x = -17.3:0.1:0.9           (% Assigning the 'x' variable…

1. Generating the DC motor model in simulink:  % Assuming the Parameters to model a DC motor J = 0.01; % Moment of inertia of the rotor in kg-m^2 b = 0.1; % Motor viscous constatnt in N-m-s Kb = 0.01; % Back EMF constant in v/rad/s Kt = 0.01; % Motor torque constant in N-m/amp Ra = 1.0; %…

1. Developing a Double-acting actuator model using simscape Multibody and simscape  Cylinder Model Designing the Mechanical system of the cylinder using simscape multibody library blocks Cylinder assembly Piston rod assembly Designing the Hydraulic system by using the Simscape library physical components Now adding the…

step-1: Importing the give data files into the matlab first and made some changes step-2: A fter imported the file fistly focus on the matlab code file i.e, "Project_initFile"   InitFile: %% Vehicle Parameters M = 1500; % Vehicle weight [kg] Cr = 0.015; % Rolling resistance coefficient Rw = 0.35; % Rolling radius…

Aim:- Modeling of development of a forward energy-based fuel consumption model of a P1 hybrid vehicle Objectives:- 1] Tabulate the fuel economy numbers (kmpl) for UDDS and HWFET cycle. Compare these numbers with the baseline numbers for conventional vehicle. 2] Plot the time trace for engine, transmission input,…

Q.1) Li-ion Batteries A lithium-ion battery or Li-ion battery is a type of rechargeable battery. Lithium-ion batteries are commonly used for portable electronics and electric vehicles and are growing in popularity for military and aerospace applications. Similar to the lead- and nickel-based architecture, lithium-ion uses…

Aim: Simulate the 3 test cases from harness dashboard and write a detailed report on the results. What is coulomb counting? Refer to the above model and explain how BMS implements coulomb counting for SOC estimation? Theory: Matlab model to simulate the 3 test conditions from harness dashboard  Part 1: Simulate…

Cell: An electric cell is a device, which converts chemical energy into electrical energy. It has two terminals, which are made up of metal: one terminal is positive ( ), while the other one is negative ( ). When the two terminals are connected to an electrical device, electric current flows through it. cell : ANR26650M1-B…

BATTERY PACK MODELING WITH TEMPERATURE AND LIFE CYCLE EFFECTS 1.AIM To simulate the thermal effects and compare life cycle performance at various temperatures, charge & discharge rates for a 10 cell series lithium ion battery model, using MATLAB. 2.Objective To analyze temperature and life cycle parameters of the 10…

Steps to define 3D Connectors as Electrical Connectors using the Electrical Part Design Workbench - i. Create/Download connector 3D ii. Mechanical Part Design Defining geometrical parameters by point and axis system (point for bundle/wire entry side, point and axis system for mating side).  iii. Electrical Part…

Clip/Clamp Definition Get the clip 3D part Define the Geometry Parameters Define part as support Define the entry point & plane Define the exit part & plane   Mechanical Part Design Workbench Define the Geometry Parameters Points and Planes - Defining the points for both sides through point definition.  …

1. Defining Deutsch DT06 – 08SA: The connector is downloaded from the given link In Part Design Work Bench: The Connector Connection Point and the Bundle Entry Point are defined on their respective mating faces The required axis system is defined for the connector connection point Then the Work Bench is changed to…

In the given diagram above, the electrical connectors are represented by numbers. 1. There are different types of connectors in ten different places.2. Bundle continuity for the two created harnesses must be checked.3. Once the two Harnesses have been created, the next step is to connect them electrically.4. Examine Harness…

  AIM- To prepare a flattened view of a previously created harness assembly OBJECTIVE- The objective of this project is to create a flattened view for a harness assembly and then place it on the drawing sheet. It is desired that the bundles with protective coverings are represented with different visuals…

Objective: The objective of the project is to route the wiring harness on given Bugatti V16 Engine and prepare flatten view drawing in CATIA V5. All types of packaging rules have to be considered while routing the harness. Also, Industry best practices should be demonstrated in design. All the necessary details like clearance,…

Prepare & Submit all necessary reports like clearance, Clipping/Clamping selection, Harness fixing requirements, Harness continuity, and Assumptions if any along with CATIA 3D data. The figure above is the Backdoor of a car for which a Wiring Harness has to be designed A wiring harness will be done for the taillights…