MAKING ALLOY WHEEL OF RENAULT DUSTER IN AUTO DESK ALIAS Objective To create the curve network and surface making for the alloy wheel what i have learn about in this four week’s. INTRODUCTION In this I have learned about curve networks and also surface making. For this challenge I went into the entire curve networks and…

MAKING CAR BUMPER IN AUTO DESK ALIAS Objective To create the curve network and surface making for the alloy wheel what i have learn about in this four week’s. INTRODUCTION In this I have learned about curve networks and also surface making. For this challenge I went into the entire curve networks and surface making. In…

MAKING CAR FENDER AND BONNET IN AUTO DESK ALIAS Objective To create the curve network and surface making for the car fender and bonnet what i have learn about in this six week’s. INTRODUCTION In this I have learned about curve networks and also surface making. For this challenge I went into the entire curve networks…

MAKING CAR STEERING WHEEL IN AUTO DESK ALIAS Objective To create the curve network and surface making for the car steering wheel what i have learn about in this six week’s. INTRODUCTION In this I have learned about curve networks and also surface making. For this challenge I went into the entire curve networks and…

MAKING CAR SEAT IN AUTO DESK ALIAS Objective To create the curve network and surface making for the car seat what i have learn about in this eight week’s. INTRODUCTION In this I have learned about curve networks and also surface making. For this challenge I went into the entire curve networks and surface making.…

MAKING KIA SPORTAGE CAR IN AUTO DESK ALIAS Objective To create the curve network and surface making for the kia sportage car what i have learn about in this nine week’s. INTRODUCTION In this I have learned about curve networks and also surface making. For this challenge I went into the entire curve networks and surface…

MAKING A SURFACE RENDERING IN AUTO DESK ALIAS Objective To create the curve network and surface making for the surface rendering what i have learn about in this week’s. INTRODUCTION In this I have learned about curve networks and also surface making. For this challenge I went into the entire curve networks and surface…

DRAFT ANALYSIS                Draft analysis is that check the tooling axis with the component  it will pass or not , when we going for injection molding it should have proper draft angle in it. In draft analysis it shows that where the component…

TOOLING AXIS Sides of the part that appear parallel with the direction of draw (The axis of the cored position (hole) or insert is parallel to the up and down movement of the mold as it opens and closes) are typically angled slightly with (draft) to ease release of the part from the mold. Insufficient draft can cause…

TOOLING AXIS Sides of the part that appear parallel with the direction of draw (The axis of the cored position (hole) or insert is parallel to the up and down movement of the mold as it opens and closes) are typically angled slightly with (draft) to ease release of the part from the mold. Insufficient draft can cause…

TOOLING AXIS Sides of the part that appear parallel with the direction of draw (The axis of the cored position (hole) or insert is parallel to the up and down movement of the mold as it opens and closes) are typically angled slightly with (draft) to ease release of the part from the mold. Insufficient draft can cause…

CAVITY Cavity is the upper half of the injection mold usually the show surface of the finished product but is mainly concave. Molds are designated as a single cavity or multi-cavity. The lower half of the mold is called CORE. CORE Cores are used for complex injection moldings in the…

TOOLING AXIS Sides of the part that appear parallel with the direction of draw (The axis of the cored position (hole) or insert is parallel to the up and down movement of the mold as it opens and closes) are typically angled slightly with (draft) to ease release of the part from the mold. Insufficient draft can cause…

TOOLING AXIS Sides of the part that appear parallel with the direction of draw (The axis of the cored position (hole) or insert is parallel to the up and down movement of the mold as it opens and closes) are typically angled slightly with (draft) to ease release of the part from the mold. Insufficient draft can cause deformation…

MASTER SECTION Master section is that is the cut section view of the solid model , For this challange we need to create a Class A ,b,c & all the engineering features should made by with the reference of master section curve . TOOLING AXIS Sides of the part that appear parallel with the direction of draw (The axis of…

HEAT STAKES & LOCATORS Heat stakes are used to join the two different parts by the method of giving heat in the top tip of the heatstakes, it will melt and deposited in the slot after it will automatically get joined. Locators are use to arres the degree of freedom , If it a xy,yx based component we will able to arres…

ASSEMBLY WORKBENCH The assembly files in CATIA are called Product files. There are two methods to invoke the Assembly Designworkbench of CATIA. The primary method to start a new product file is by selecting File >New from the menu bar to open the Newdialog box From this dialog box select Product. PROCEDURE Hear…

MASTER SECTION Master section is that is the cut section view of the solid model , For this challange we need to create a Class A ,b,c & all the engineering features should made by with the reference of master section curve . TOOLING AXIS Sides of the part that appear parallel with the direction of draw (The axis of…