2R ROBOTIC ARM AIM: To simulate the forward kinematics of a 2R Robotic Arm by creating a MATLAB program. OBJECTIVE: To create an animation of the simulation Theory: Robotic Arm – A robotic arm is a type of mechanical arm, usually programmable, with similar functions to a human arm; the arm…

SECOND ORDER ODEsAIM: To solve an ODE that represents the equation of motion of a simple pendulum with damping.OBJECTIVE: To write a program that solves the following ODE which represents the equation of motion of a simple pendulum with damping and create an animated video of the output obtained by solving this ODE.THEORY:…

GENETIC ALGORITHM AIM: To write a MATLAB program to optimize the stalagmite function and find the global maxima of the function. OBJECTIVE: to optimize the Stalagmite function and find the global maxima of the function by clearly explaining the concept of genetic algorithm and plotting the graph for the three studies i.e.…

AIM: To write a MATLAB program that extracts the 14 coefficients and calculates the enthalpy, entropy, and specific heats for all the species in the data file OBJECTIVES: To develop a function that extracts the 14 coefficients and calculates the enthalpy, entropy, and specific heats for all the species in the…

AIM: To create a Rankine Cycle simulator using MATLAB. OBJECTIVE: To Simulate a Rankine cycle using Matlab. Extracting Steam and water properties from XSteam data (IAPWS IF - 97 standard) Calculating all state points of the cycle based on inputs. Plotting the 'T' vs 'S' and 'H' vs 'S' plot for the given input. THEORY:…

Week 8 - Challenge 1 - Base Bracket Design AIM:  To create the Base Bracket Plastic component through the given Class-A surface.INTRODUCTION:CLASS-A SURFACE: A surface created by the designer that the plastic modeler uses as an input. It is the most exterior and aesthetically pleasing surface.CLASS-B SURFACE: Class-B…

WEEK 8 – CHALLENGE 2 --> DESIGN AND DRAFT ANALYSIS OF SWITCH BEZEL OBJECTIVE – The objective of the project is to design the switch bezel and to do a draft analysis for it by creating the required tooling direction with the help of bisecting method. INTRODUCTION – The control panel bezel is the…

WEEK 8 - CHALLENGE 3 --> DESIGN OF COIN HOLDER AIM: To create the coin holder plastic component through the given Class A surface. To begin with, the tooling axis for the given Class-A surface should be created meeting the requirements of the draft angle and at the end perform the draft analysis on the model. Take…

 WEEK 8 - CHALLENGE 4 --> BUMPER DESIGN   AIM: To make a model from the provided class-A surface. INTRODUCTION: CLASS-A SURFACE: a surface made by the designer which is given as input to the plastic modeler to work on. It is an aesthetic surface and the outermost surface. CLASS-B SURFACE: a…

WEEK 8 - CHALLENGE 6 - CORE & CAVITY DESIGN   AIM: To create a switch bezel from the given A-class surface by considering a thickness of 2.5 mm and also creating Core and Cavity blocks for it. PROCEDURE: Class A surface : The input of the product designer is in the form of the A-class surface. The job of…

AIM: To Create the Door Handle Component from the given Class-A surface. To Create the tooling axis for the given Class-A Surface meeting the requirements of the draft angle. To Attach B side Features in the component. To perform the Draft analysis on the model.  TOOLS USED: Boundary Join Multiple extracts Bisecting…

WEEK 9 - CHALLENGE 2 Attachment Feature Creation AIM: To Create the door Trim Component from the given Class-A surface. To Create the Tooling axis for the given Class-A Surface meeting the requirements of the draft angle. To perform the Draft analysis on the model.  To Create the B Side Feature in the component by…

WEEK 9 - PROJECT - PILLAR DESIGN WITH MASTER SECTION   AIM - To create the Pillar, Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model.  …

BENCHMARKING   AIM:  To write a report outlining what benchmarking is, compare at least four vehicles, and offer an acceptable conclusion for the report by recommending a car from those under consideration. BENCHMARKING: It involves evaluating one's business operations and performance indicators against…

UNDERBODY COATING   AIM: To study the underbody coating used in automobile industries. Underbody Coating is a sprayable coating, which protects the undersurface of the vehicle from corrosion. The underbody of the car is long-term protected against corrosion by underbody coating. Additionally, it safeguards inside…

                                                             Challenge - HOOD DESIGN Aim: - The main objective of this project is to learn the essential tools, commands, and surface modeling of Hood designing using Siemens NX Cad. This project is to develop a design idea for hood BIW that satisfies the manufacturing requirements,…

                                     Challenge - SECTION MODULUS OF THE HOOD Objective: To find the section modulus of the hood and optimization to improve the overall section modulus. Section Modulus: The section modulus (S) is the geometric property of the cross-section used for designing beams and flexural members.…

                                                      Challenge - WHEEL ARC (Fender Design) OBJECTIVE: The objective of the wheel arc challenge is to calculate the wheel arc area using…

CHALLENGE - FENDER DESIGN OBJECTIVE: To design a fender using a new age design software - NX - CAD INTRODUCTION:  Any product's design begins with a requirement. Based on the requirements, the design engineer creates a sketch of the product. Using cutting-edge CAD software, the 2D sketch that has the correct…