1) CHALLENGE NO. 04 – CONCEPT MODELLING OF ALLOY WHEEL                                                                           …

CHALLENGE . 05 – CONCEPT MODELLING OF A CAR BUMPER                                                                           …

  1)CHALLENGE 06 – CONCEPT MODELLING OF FENDER                                                                        …

  CHALLENGE . 07 – CONCEPT MODELLING OF STEERING WHEEL                                                                                 …

CHALLENGE . 08 – CONCEPT MODELLING OF SEAT                                                                            …

  CHALLENGE . 09 – TECHNICAL SURFACING KIA SPORTAGE                                                                   …

1)STANDARD MODELLING VIEWS OF RENDERING OF KIA SPORTAGE:-                                                                           …

Design and Draft Analysis of the Base Bracket OBJECTIVE The objective of the project is to design the class B and C surface for the Base bracket with the given class A surface and Draft analysis must be carried out by creating a perfect Tooling direction by using the Bisecting method. INTRODUCTION The Draft Analysis command…

                                                           DRAFT ANALYSIS REPORT DRAFT ANGLE A draft angle is a taper applied to the vertical walls of the injection molded…

DESIGN OF COIN HOLDER AIM: To create the coin holder plastic component through the given Class A surface. Tobegin with the tooling axis for the given Class-A surface should be created meeting therequirements of the draft angle and at the end perform the draft analysis on the model.Take the thickness of the component to…

TOOLING AXIS Sides of the part that appear parallel with the direction of draw (The axis of the cored position (hole) or insert is parallel to the up and down movement of the mold as it opens and closes) are typically angled slightly with (draft) to ease release of the part from the mold. Insufficient draft can cause…

Aim/Objectives: Create the Core and cavity blocks for the switch bezel designed in the earlier challenge. Steps Followed: Tooling Axis creation Checking Draft analysis for created tooling Axis Creating parting Surface Creating Core Side Creating cavity side. 1). Tooling Axis: Tooling axis is the axis in which core…

AIM     To make a full solid model from the provided lower door trim A surface and make ribs & screw boss. INTRODUCTION: CATIA:          It means Computer-Aided Three-Dimensional Interactive Application.  It is computer aided designing software.…

Objective: The main aim of this challenge is to create B-side features of the 'Door Trim', with the help of CATIA V5. Overview: Created a 2.5mm solid part body of door trim with the help of class A surface, and created a B-side attachment feature 'Dog House' by considering the design parameters. Tooling axis:…

CREATION OF HEAT STAKES & LOACTORS FOR DOOR APPLIQUE OBJECTIVE: The main objective of this challenge is to create tooling axis for the Door Applique surface considering the draft and to create class-B and C surfaces using class-A and adding heat stakes and locators to the final solid component and to perform draft…

  CONNECTOR DEFINATIONS IN CATIA V5 1. Deutsch DT06 – 08SA Connector connection point             Create midpoint on the contact face which will be normal to wire bunddle insertion. Craete Axis System with respect to the point which we have created and defining the axis direction…

  Q1 The given clip was downloaded and opened as a part file. I have to define two points that will be used as entry and exit points. Then a plane has to be defined at the points. A base plane has to be defined at a distance of 2 to 3 mm from the clip. again we define the exit point at the first definition as the…

Aim:  1) To Route the following harness layout in the Electrical workbench. 2) Add protective covering on all branches connected to DT06-2S & DT06-4S connectors. Given: CAD data of the following Connectors:  DT06-4S DT06-6S DT06-2S DT06-08SA Connectors Layout Design: Steps to be followed: 1. Download…

                                                                                           …

AIM: TO FLATTEN THE WIRING HARNESS AND DRAFT THE WIRING HARNESS ASSEMBLY. GIVEN: HARNESS ASSEMBLY: HARNESS FLATTENING: WE GO TO THE HARNESS FLATTENING WORKBENCH AND DEFINE THE FLATTENING PARAMETERS. WE USE THE EXTRACT COMMAND TO BRING THE HARNESS ASSEMBLY TO THE FLATTENING WORKBENCH HERE. HARNESS ASSEMBLY: HARNESS FLATTENING:…

  AIM To create a door interior part from the inputs of class A surface along with master section by following the design rules followed in tier 1 and OEM industries in catia v5 SOFTWARE USED CATIA V5 OBJECTIVES Create a sketch by using Positioned sketch All the should be sketches should be Iso-Constrained Ensured…

WIRING HARNESS DESIGN PROJECT 1 AIM Design and develop the Wiring harness on Given V6 Engine and Prepare flatten view drawing in CATIA V5. Application of all Packaging rules, Industry best practices studied in this course shall be demonstrated in design.   INTRODUCTION A wire harness, also commonly referred to as…

Project 2 Project 2         Objective:   Statement of assignment: Route the Wiring harness on the given car body and prepare a flattened view drawing in CATIA V5. Application of all Packaging rules, Industry best practices studied in this course shall be demonstrated in design. Apply Protection…

BENCHMARKING CHALLENGE  OBJECTIVE:Benchmarking study of the vehicles which falls under 8-10 lakhs and provide with the best fit for the person with all the consideration and features following the place, use and cost.   BENCHMARKING: Benchmarking involves a structured comparison between similar products,services…

Under body coating Its a coating done on car under body to protect it from corrosion. Just like how people require shelter and additional care, cars need them too. Just parking your car inside a garage will not solve the problem as the car is exposed to ever-changing weather conditions especially in a country like…

Hood Design in CATIA V5:Objective:Design hood outer panel, inner panel and reinforcements with the given outer hood skin, master section and design parameters. Introduction:The hood or bonnet is the hinged cover over the engine of motor vehicles. Hoods can open to allow access to the engine compartment   …

Section Modulus calculation and optimization AIM Use the Section from your Hood design and calculate the section modulus,Come up with a new section that has improved the section modulus of the previous section and mention what change you made that has increased the strength.             …

Wheel Arch gap - Calculations   Aim :      To calculate the wheel arch gap at required points and check whether the car passes the European standard. Objective : Study about the different wheel arch gap standards. Draw the lines at the required angle and points for the European standard. Measure the…

                                           Fender Design   OBJECTIVE : The objective of the project is design a fender using CATIA V5 FENDER : The main purpose of the fender is to prevent sand,mud, rocks,liquids…

CAR ROOF DESIGN BY USING CATIA V5:-                                                                                …

  Design of the  car backdoor using Catia V5 purpose :- To create the following components of the backdoor panel from the given styling surface. Inner panel,  The upper outer panel,  Outer lower panel with the Hinge reinforcement (left and right) Gas stay reinforcement (left and right) Latch reinforcement …