…

                                                                                           …

1 PROBLEM STATEMENT Consider two plates of same dimension 300 x 120 x 30 mm. Plate-1 consists of a single central hole of diameter 60 mm. Plate-2 will be having two additional holes at a distance of 90mm from central hole along length (one at left side & other hole at right side). The diaa of smaller hole is 30 mm.…

1 PROBLEM STATEMENT Carry out a static structural analysis to find out EQUIVALENT STRESS, TOTAL DEFORMATION AND STRESS INTENSITY using CAST IRON (ductile), CAST STEEL, CAST BRONZE. FIND LOCATION FOR POSSIBLE FRACTURE. 2 INTRODUCTION & THEORY Spur Gear is a mechanical device used for power transmition from input…

1 PROBLEM STATEMENT CONDUCT TENSILE TEST & TORSION TEST ON THE SPECIMEN. Refer following table for boundary condition NATURE OF TEST B.C. ON END-1 B.C. ON END-2 TENSILE FIXED SUPPORT 18mm displacement TORSION FIXED SUPPORT 1200 degree of rotation   USE STEEL 1006 AS A MATTERIAL Find out the total deformation, equivalent…

1 PROBLEM STATEMENT Give a brief description on usage & advantage of CHT analysis. Choose proper turbulence model & maintain a corresponding y+ values & justify your results. Calculate the wall/surface heat transfer coefficient on internal solid surface. Also plot velocity & temperature profile in appropriate…

1 OBJECTIVE Perform RT INSTABILITY simulation for base mesh size as 0.5mm & after base mesh simulation refine mesh & re-do the simulation. Use air & water as a fluid for above cases. Now create a user defined fluid instead of air whose density is 400Kg/m3 & viscosity as 0.001kg/m-s & use refined mesh…

1 INTRODUCTION Before manufacturing any product basically its model should be tested under the similar conditions and with some assumptions. Modelling and testing is the basic step towards manufacturing any product and analysis of the results will gives idea about the product. Now a day’s numerical simulation is…

1 OBJECTIVE Calculate separator efficiency & pressure drop at constant velocity of 3m/s & vary particle size from 1micron to 5 microns. Later on, keep particle size constant at 5micron & vary particle velocity from 1 m/s to 5m/s & recalculate pressure drop &efficiency. 2 INTRODUCTION Role of separators…

1 OBJECTIVE Perform the numerical Simulation to observe the sloshing effect of lubricating fluid like engine oil & n-heptane (c7h16) at an immersion of 20% & 30% of lubricating fluid. Also comment on error caused during simulation. 2 INTRODUCTION Performance of any mechanical device heavily depends on type of power…

1 OBJECTIVE PARAMETRIC STUDY OF GATE VALVE by changing lift from 10mm to 80mm. Also calculate Cv & Kv. 2 INTODUCTION Gate valve is an important device used in industrial application where flow of fluid like oil & gasses are involved. It has its application in automotive, marine, pharmaceuticals, & manufacturing…

1 Objective To study about the combustion simulation on combustor model using ANSYS Fluent and analysis of NOx formation and soot formation in the combustion product. Process of reduction in formation in NOx and soot in combustion product is also analysed by using one step soot model in during simulation ANSYS Fluent.…

OBJECTIVE Aim of the simulation is to perform a steady state conjugate heat transfer on the cad model of graphics card. We have to vary the velocity from 1m/s to 5m/s & compare the final temperature of the GRAPHICS CARD. We have to plot & compare the different countours of temperature & wall heat transfer coefficient.…

1 PROBLEM STATEMENT Perform static structural analysis on Rail wheel and Track setup by varying bearing load from 100KN to 500KN. Compare Total Deformation, Equivalent stress and the life under both the loads. Also create user defined result to calculate Total Deformation & validate with the inbuilt ANSYS result. 2…

OBJECTIVE Perform geometrical cleanup after performing geometry check for multiple checks & rectify them to ensure a close surface for performing a CFD meshing using element size of 1mm, 3mm, 5mm. The nature of element shape should be TRIA element. GEOMETRY Below is the CAD model required for preprocessing. This model…

OBJECTIVE Perform geometrical cleanup after performing geometry check for multiple checks & rectify them to ensure a close surface for performing a CFD meshing using specified element size. The nature of element shape should be TRIA element. Specified Element Size COMPONENTS Target Size in mm Minimum Size in mm Maximum…

link to download file: BMW ANSA PREPROCESSING OBJECTIVE Perform geometrical cleanup after performing geometry check for multiple checks & rectify them to ensure a close surface for performing a CFD meshing using specified element size. The nature of the element shape should be TRIA element. Specified Element Size…

OBJECTIVE: Extract mid surface of given component & perform 2D meshing. The element size must be 5 mm. There is some spot identified as alphabet from a to f. We have to apply (1D Element along with corresponding links) the rod, bar, beam, & spring elements as specified in the problem statement. We have to also…

  OBJECTIVE: PERFORM SURFACE WARP AFTER MERGING ALL 3 GEOMETRY Perform geometrical cleanup after performing geometry check for multiple checks & rectify them to ensure a close surface for performing a CFD meshing using appropriate element size. The nature of the element shape should be TRIA element.…

LINK TO ANSA FILE: CYBERTRUCK WIND TUNNEL OBJECTIVE Perform geometrical cleanup after performing geometry check for multiple checks & rectify them to ensure a close surface for performing a CFD meshing using specified element size. The nature of the element shape should be TRIA element. Specified Element Size…