Soil Anchors Analysis and Applications
Notes written by Skill-Lync from the recording · Updated 17 Nov 2026
This page used to play a second video that was not about soil anchors: a pre-engineered steel building case study, which is part 2 of Skill-Lync's structural optimisation by pre-engineering workshop. It now shows the soil anchors recording only.
What this workshop covers
This workshop covers soil anchors and ground anchors: how they work, their types, uses and design, with a short slope analysis demo in GeoStudio SLOPE/W. The instructor frames anchors as the opposite of piles: a pile takes compression into the ground, while an anchor gives soil the tension capacity it lacks. He classifies anchors by installation (plate anchors in excavated holes, driven or augered anchors) and by material (grouted tendons, steel cables, rock bolts and soil nails, epoxy-bonded bars), then covers applications in highway retaining walls, slope stabilisation, dam foundations and tall towers, and compares single-bar and multi-strand cross sections.
The design part explains the factor of safety as resisting force over driving force, limit equilibrium methods including Morgenstern-Price, pull-out testing, and early soil cone and friction cylinder models. The demo builds a slope, runs 1,331 trial slip circles and adds a nail reinforcement.
It suits civil and geotechnical students who want an introduction. This Skill-Lync session is from June 2021 and stays conceptual, with no design calculation worked through.
Chapters
- 0:00 Ground anchors as the tension counterpart of piles
- 3:27 Plate anchors vs driven and augered anchors
- 5:48 Grouted anchors, cables, rock bolts, soil nails
- 8:07 Uses: retaining walls, slopes, dams, towers
- 11:51 Single-bar vs multi-strand anchors, micropiles
- 17:17 Factor of safety and limit equilibrium methods
- 20:00 Pull-out tests and the soil cone model
- 23:10 Software as a black box: SLOPE/W, Plaxis, Abaqus
- 26:19 SLOPE/W demo: slip surfaces and a nail reinforcement
Key points from the session
- Soil has little or no tensile strength unless it is cohesive, so an anchor plays the role that rebar plays in concrete: the tendon carries tension and the grout around it develops friction with the ground to resist pull-out.
- By installation, plate anchors are placed in an excavated hole, pretensioned and buried, as used for transmission and communication towers, while driven or augered anchors are pushed or screwed in without excavation, much like bored versus driven piles.
- Many small bars or soil nails are preferred over a few large ones for redundancy: if one breaks, the slope does not fail suddenly but deforms slowly enough for people to notice and repair it. Multi-strand anchors work the same way, breaking strand by strand.
- Anchor stability is judged by the factor of safety, the ratio of resisting force to the force trying to overturn or slide the structure. Limit equilibrium methods are standard, and Morgenstern-Price is the one the instructor treats as the modern default.
- Design checks include pull-out tests, full-scale or small-scale, in the same spirit as a pile load test. The instructor also allows for loads that arrive later in the structure's life, such as creep, corrosion and thermal effects, quoting a split of roughly 80% initial and 20% later load that varies by project.
- In the SLOPE/W demo a grid of 10 x 10 centres with 10 radius increments is set up; the software adds one to each count, so 11 x 11 x 11 gives 1,331 trial slip surfaces. A nail reinforcement is then drawn with tensile capacity, bond diameter, spacing and resistance reduction factor.
- The instructor's selection rule of thumb: self-drilling anchors for soil and for large structures, rock bolts for rock, and bolts or micropiles for small structures.
What is the difference between a pile and a soil anchor?
A pile is designed mainly to carry compression from a structure down into the ground. A soil or ground anchor is designed for tension: it holds a wall, slope or tower back against forces trying to pull it out or overturn it. The instructor notes piles have some pull-out capacity and the two are sometimes combined.
Which software does the session use to analyse anchored slopes?
The demo uses GeoStudio SLOPE/W with the Morgenstern-Price method to find the factor of safety over 1,331 trial slip circles, then adds a nail. The instructor also mentions Rocscience, Plaxis with c-phi reduction, and Abaqus with Python post-processing, and warns that software always returns an answer, so you must check it makes sense.
Where to go next
- Course: sub-surface exploration and geotechnical investigation
- Workshop recording on shoring and deep excavation, with notes
- Full workshop on optimising steel frames by pre-engineering (the steel-building video this page used to play)
- Solved GATE civil foundation engineering questions on piles and earth pressure
- Geotechnical engineering in site investigation and soil stabilisation
Who should watch
For Civil Engineers
A 9 Jun 2021 workshop recording from Skill-Lync on CIVIL. For a structured course with projects on this topic, see Skill-Lync's civil engineering courses.